Paul Davidson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Paul Davidson has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Anthony M. Waas
Univ Michigan, Dept Aerosp Engn, Ann Arbor, MI 48109 USA
9 shared publications Mark Smeets
5 shared publicationsAnkur Jain
4 shared publicationsAnthony M. Waas
4 shared publicationsAnthony Waas
3 shared publicationsSandesh Amgai
3 shared publications
Latest Publications
- Open Access
- 9 May 2026
- Published by Elsevier in SSRN Electronic Journal
A Systematic 3D Homogenization Study of Symmetry-Governed Micropolar Stiffness Coupling in Lattice Metamaterials
The mechanical behavior of lattice metamaterials depends not only on constituent material properties but also on the symmetry of their microstructure. Classical continuum theories cannot capture the full deformation behavior, including rotational interactions arising at strut junctions and plate interfaces, whereas micropolar elasticity provides a more suitable higher-order continuum framework. However, a systematic link between crystallographic point group symmetry and the structure of the full $18 \times 18$ micropolar stiffness tensor has not been established using displacement-driven homogenization. Here, a 3D displacement-driven homogenization approach is applied to shell-based lattice unit cells spanning symmetry classes from centrosymmetric ($m\overline{3}m$) to fully asymmetric ($1$), including cuboid plate assemblies and re-entrant geometries. All 18 macroscopic deformation modes are imposed to fully resolve the micropolar stiffness tensor. The results reveal a direct correspondence between symmetry and tensor structure: mirror symmetry breaking activates strain–curvature and rotation couplings through $\overline{\mathbb{N}}$ and $\overline{\mathbb{Q}}$, while rotational asymmetry governs shear–rotation coupling via $\overline{\mathbb{M}}$, with progressive symmetry reduction systematically populating additional coupling terms. A key finding is that major asymmetry arises in all non-centrosymmetric lattices even under a strain-energy-based formulation, and that periodic scaling preserves coupling structure when symmetry is retained, whereas symmetry-reducing geometric changes introduce additional admissible couplings. These results establish a symmetry-based framework for designing lattice metamaterials with tailored higher-order mechanical coupling behavior.- 9 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Systematic 3D Homogenization Study of Symmetry-Governed Micropolar Stiffness Coupling in Lattice Metamaterials
The mechanical behavior of lattice metamaterials depends not only on constituent material properties but also on the symmetry of their microstructure. Classical continuum theories cannot capture the full deformation behavior, including rotational interactions arising at strut junctions and plate interfaces, whereas micropolar elasticity provides a more suitable higher-order continuum framework. However, a systematic link between crystallographic point group symmetry and the structure of the full $18 \times 18$ micropolar stiffness tensor has not been established using displacement-driven homogenization. Here, a 3D displacement-driven homogenization approach is applied to shell-based lattice unit cells spanning symmetry classes from centrosymmetric ($m\overline{3}m$) to fully asymmetric ($1$), including cuboid plate assemblies and re-entrant geometries. All 18 macroscopic deformation modes are imposed to fully resolve the micropolar stiffness tensor. The results reveal a direct correspondence between symmetry and tensor structure: mirror symmetry breaking activates strain–curvature and rotation couplings through $\overline{\mathbb{N}}$ and $\overline{\mathbb{Q}}$, while rotational asymmetry governs shear–rotation coupling via $\overline{\mathbb{M}}$, with progressive symmetry reduction systematically populating additional coupling terms. A key finding is that major asymmetry arises in all non-centrosymmetric lattices even under a strain-energy-based formulation, and that periodic scaling preserves coupling structure when symmetry is retained, whereas symmetry-reducing geometric changes introduce additional admissible couplings. These results establish a symmetry-based framework for designing lattice metamaterials with tailored higher-order mechanical coupling behavior. - Open Access
- 21 February 2026
- Published by Elsevier in SSRN Electronic Journal
Ray-Tracing-Based Modeling and Experimental Validation of Irradiance Fields in Xenon Flashlamp Heating Systems with Quartz Light Guides
Flashlamp-based heating enables millisecond-scale thermal processing for manufacturing applications such as annealing and in-situ consolidation of composite parts, but the large parameter space of lamp operation and optical delivery hardware often necessitates extensive trial-and-error tuning. This work develops and validates a ray-tracing-based optical model of a xenon arc flashlamp, both with and without a three-faceted fused-silica light guide, to predict spatially resolved irradiance fields for process modeling. Full-field irradiance measurements were acquired using a water-cooled Gardon gauge mounted on a six-axis robotic arm, producing dense irradiance maps around the bare lamp and the lamp–guide assembly. The optical model was implemented in TracePro using measured spectral emission data and a calibrated angular radiation pattern, with lamp housing reflections represented by an idealized high-reflectivity surface. A parametric calibration study identified an 18 mm diameter cylindrical emitter as the best single-source approximation. To better capture the experimentally observed central irradiance enhancement, a two-source representation was introduced by augmenting the cylindrical emitter with a secondary planar emitter, yielding modest improvements in agreement with measurements across multiple planes (RMSE as low as ∼ 0.007 for lamp-only profiles). For the lamp with the three-faceted quartz guide, the model reproduced key irradiance features near the top facet, including peak magnitudes of 0.26– 0.27 MW/m2, with localized discrepancies attributed primarily to measurement resolution near sharp geometric transitions. Finally, a sensitivity study on the guide taper angle (0◦–7◦) revealed a trade-off between irradiance intensification at the top facet and side-facet leakage, with maximum irradiance of 0.485 MW/m2 at a 4◦ taper and an application-relevant design range of approximately 3◦–6◦. The validated modeling framework provides a pathway for predicting delivered irradiance in flashlamp-based manufacturing and for guiding optical design toward reduced empirical tuning.
- 21 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessRay-Tracing-Based Modeling and Experimental Validation of Irradiance Fields in Xenon Flashlamp Heating Systems with Quartz Light Guides
Flashlamp-based heating enables millisecond-scale thermal processing for manufacturing applications such as annealing and in-situ consolidation of composite parts, but the large parameter space of lamp operation and optical delivery hardware often necessitates extensive trial-and-error tuning. This work develops and validates a ray-tracing-based optical model of a xenon arc flashlamp, both with and without a three-faceted fused-silica light guide, to predict spatially resolved irradiance fields for process modeling. Full-field irradiance measurements were acquired using a water-cooled Gardon gauge mounted on a six-axis robotic arm, producing dense irradiance maps around the bare lamp and the lamp–guide assembly. The optical model was implemented in TracePro using measured spectral emission data and a calibrated angular radiation pattern, with lamp housing reflections represented by an idealized high-reflectivity surface. A parametric calibration study identified an 18 mm diameter cylindrical emitter as the best single-source approximation. To better capture the experimentally observed central irradiance enhancement, a two-source representation was introduced by augmenting the cylindrical emitter with a secondary planar emitter, yielding modest improvements in agreement with measurements across multiple planes (RMSE as low as ∼ 0.007 for lamp-only profiles). For the lamp with the three-faceted quartz guide, the model reproduced key irradiance features near the top facet, including peak magnitudes of 0.26– 0.27 MW/m2, with localized discrepancies attributed primarily to measurement resolution near sharp geometric transitions. Finally, a sensitivity study on the guide taper angle (0◦–7◦) revealed a trade-off between irradiance intensification at the top facet and side-facet leakage, with maximum irradiance of 0.485 MW/m2 at a 4◦ taper and an application-relevant design range of approximately 3◦–6◦. The validated modeling framework provides a pathway for predicting delivered irradiance in flashlamp-based manufacturing and for guiding optical design toward reduced empirical tuning.
- 24 September 2025
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 324
Stiffness tailoring for enhanced buckling performance of isotropic panels
- 24 September 2025
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 324
Stiffness tailoring for enhanced buckling performance of isotropic panels
- 20 December 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (3) , 383-393
Low velocity impact resistance of multilayer composite structures for mitigating acceleration
In this manuscript the low velocity impact resistance of a novel multilayered energy absorbing structure was studied and compared to the materials used in US Army Advanced Combat Helmets. We investigate the dynamic performance of 3D printed lattice structures sandwiched between carbon fiber composites and Kevlar fabrics to develop helmets that are lighter and have better blast protection. The energy absorbed by the sandwich structure was recorded based on the difference in acceleration between the top impacted surface and the base of the structure. A multi degree of freedom non-linear spring mass model was used to predict the response of the multilayer sandwich structures. Nonlinear stiffness values were determined through compression experiments. A good agreement between the model and the experiment at the measured boundary allows for better understanding of the material layers and provides a modeling framework for future predictions and optimization efforts. This study provides insights into the use of digitally 3D printed cellular materials, carbon fiber composites, and Kevlar fabrics to provide superior impact performance at a lighter weight compared to existing helmet systems.
- 20 December 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (3) , 383-393
Low velocity impact resistance of multilayer composite structures for mitigating acceleration
In this manuscript the low velocity impact resistance of a novel multilayered energy absorbing structure was studied and compared to the materials used in US Army Advanced Combat Helmets. We investigate the dynamic performance of 3D printed lattice structures sandwiched between carbon fiber composites and Kevlar fabrics to develop helmets that are lighter and have better blast protection. The energy absorbed by the sandwich structure was recorded based on the difference in acceleration between the top impacted surface and the base of the structure. A multi degree of freedom non-linear spring mass model was used to predict the response of the multilayer sandwich structures. Nonlinear stiffness values were determined through compression experiments. A good agreement between the model and the experiment at the measured boundary allows for better understanding of the material layers and provides a modeling framework for future predictions and optimization efforts. This study provides insights into the use of digitally 3D printed cellular materials, carbon fiber composites, and Kevlar fabrics to provide superior impact performance at a lighter weight compared to existing helmet systems.
- Open Access
- 9 November 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (3) , 321-330
Machine learning based segmentation of delamination patterns from sparse ultrasound data of barely visible impact damage in composites
Composite laminates, known for their strength and flexibility, are widely used but can delaminate under certain barely visible impact. Ultrasound Transmission (UT) scans can detect such failures, but the noise in the scans makes automation of delamination morphology challenging. Machine learning could solve this, but it requires substantial training data. Furthermore, given the considerable time and cost of conducting impact tests on composite laminates, such data remains sparse. This study overcomes data sparsity by enlarging UT scan dataset using image augmentation techniques and synthetic data generation methods. A combination of rotation and elastic deformation of real UT images produced augmented data. Synthetic data was generated by mimicking the statistical variations in real data, including delamination length and rotation per ply, and adding gradients to match the original image noise. A U-Net based machine learning segmentation approach was utilized to capture local and global information through a series of convolutions to apply per-pixel classification. Systematic experimentation was conducted to study the influence of adding augmented and synthetic data on segmentation accuracy. The results show that the use of augmented data increases accuracy significantly. With the addition of synthetic data to the augmented data, there is a marginal improvement in accuracy. However, feature edge accuracy is significantly improved. The preliminary results presented here show the promising use of machine learning techniques for complex, non-destructive inspection methods.
- 9 November 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (3) , 321-330
Open AccessMachine learning based segmentation of delamination patterns from sparse ultrasound data of barely visible impact damage in composites
Composite laminates, known for their strength and flexibility, are widely used but can delaminate under certain barely visible impact. Ultrasound Transmission (UT) scans can detect such failures, but the noise in the scans makes automation of delamination morphology challenging. Machine learning could solve this, but it requires substantial training data. Furthermore, given the considerable time and cost of conducting impact tests on composite laminates, such data remains sparse. This study overcomes data sparsity by enlarging UT scan dataset using image augmentation techniques and synthetic data generation methods. A combination of rotation and elastic deformation of real UT images produced augmented data. Synthetic data was generated by mimicking the statistical variations in real data, including delamination length and rotation per ply, and adding gradients to match the original image noise. A U-Net based machine learning segmentation approach was utilized to capture local and global information through a series of convolutions to apply per-pixel classification. Systematic experimentation was conducted to study the influence of adding augmented and synthetic data on segmentation accuracy. The results show that the use of augmented data increases accuracy significantly. With the addition of synthetic data to the augmented data, there is a marginal improvement in accuracy. However, feature edge accuracy is significantly improved. The preliminary results presented here show the promising use of machine learning techniques for complex, non-destructive inspection methods.