Tuomo Siponkoski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tuomo Siponkoski has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Heli Jantunen
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering, University of Oulu, Oulu, Finland
13 shared publications - Jari Juuti
University of Oulu
9 shared publications Jari Juuti
5 shared publications- Jani Perantie
University of Oulu Microelectronics and Materials Physics Laboratories P.O. Box 4500, FI-90014 Oulu, Finland
4 shared publications - Mikko Nelo
Microelectronics Research Group Advanced Electronics Centre Faculty of Information Technology and Electrical Engineering University of Oulu Oulu Finland
4 shared publications Mikko Nelo
3 shared publications
Latest Publications
- Open Access
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. PP (10577157) , 1-10
Actuating Liquid Metal in Microchannels With Minimized Electrolyte for Reconfigurable RF Applications
Surfaces with reconfigurable conductive elements are key enabling technologies for 6G communications. They require fast, reliable, and low-loss reconfiguration mechanisms. This work presents a method for actuating liquid metal (LM), eutectic gallium–indium (EGaIn). Conventional hydraulic actuation of LM (via bulk carrier liquids) causes metal fragmentation, high actuation pressure, and degradation in electromagnetic (EM) performance. EGaIn is particularly difficult to move reliably because it forms a native oxide that sticks to the walls of channels. To address these challenges, a method to minimize carrier liquid is demonstrated. Laser-micromachined glass microchannels are employed, where the fabrication process inherently produces rough walls. This roughness enables a microscopically thin NaOH(aq) film to be formed only at the interface between the microchannel and EGaIn. This film layer can readily remove the oxide skin, resulting in stable and low-friction actuation.[2026-0022]
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. PP (10577157) , 1-10
Open AccessActuating Liquid Metal in Microchannels With Minimized Electrolyte for Reconfigurable RF Applications
Surfaces with reconfigurable conductive elements are key enabling technologies for 6G communications. They require fast, reliable, and low-loss reconfiguration mechanisms. This work presents a method for actuating liquid metal (LM), eutectic gallium–indium (EGaIn). Conventional hydraulic actuation of LM (via bulk carrier liquids) causes metal fragmentation, high actuation pressure, and degradation in electromagnetic (EM) performance. EGaIn is particularly difficult to move reliably because it forms a native oxide that sticks to the walls of channels. To address these challenges, a method to minimize carrier liquid is demonstrated. Laser-micromachined glass microchannels are employed, where the fabrication process inherently produces rough walls. This roughness enables a microscopically thin NaOH(aq) film to be formed only at the interface between the microchannel and EGaIn. This film layer can readily remove the oxide skin, resulting in stable and low-friction actuation.[2026-0022]
- Open Access
- 3 February 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
Magnetoelectric antennas: Fundamentals, state-of-the-art, challenges, and future perspectives
One of the biggest challenges in antenna design for communication and sensing is their challenges in miniaturization. Despite the introduction of various miniaturization methods and their effectiveness, miniaturization techniques based on the electromagnetic (EM) mechanism have reached their limits. Recently, acoustically actuated antennas based on magnetoelectric (ME) principles have emerged, proving to be capable of reducing the size of antennas by four to five orders of magnitude compared to conventional EM antennas. This paper overviews the operational principles of ME antennas and reviews their state-of-the-art designs and structures, including an analysis of their commonly used materials and properties, along with their applications. Different experimental platforms required for evaluating ME antennas are also discussed.
- 3 February 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
Open AccessMagnetoelectric antennas: Fundamentals, state-of-the-art, challenges, and future perspectives
One of the biggest challenges in antenna design for communication and sensing is their challenges in miniaturization. Despite the introduction of various miniaturization methods and their effectiveness, miniaturization techniques based on the electromagnetic (EM) mechanism have reached their limits. Recently, acoustically actuated antennas based on magnetoelectric (ME) principles have emerged, proving to be capable of reducing the size of antennas by four to five orders of magnitude compared to conventional EM antennas. This paper overviews the operational principles of ME antennas and reviews their state-of-the-art designs and structures, including an analysis of their commonly used materials and properties, along with their applications. Different experimental platforms required for evaluating ME antennas are also discussed.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- p. 1-5
Sub-THz Reconfigurable Beam-Splitting Reflector Using Actuated Liquid Metal
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- p. 1-5
Open AccessSub-THz Reconfigurable Beam-Splitting Reflector Using Actuated Liquid Metal
- Open Access
- 11 March 2024
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 53 (14) , 6282-6288
Centrosymmetric to non-centrosymmetric transition in the Ca2−xMnxTi2O6 double perovskite system studied through structural analysis and dielectric properties
Ca2−xMnxTi2O6 double perovskite is synthetized with high-pressure methods and its centrosymmetric to non-centrosymmetric transition is studied in the range 0 ≤ x ≤ 1 to determine the optimal composition range for ferroelectric properties.
- 11 March 2024
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 53 (14) , 6282-6288
Open AccessCentrosymmetric to non-centrosymmetric transition in the Ca2−xMnxTi2O6 double perovskite system studied through structural analysis and dielectric properties
Ca2−xMnxTi2O6 double perovskite is synthetized with high-pressure methods and its centrosymmetric to non-centrosymmetric transition is studied in the range 0 ≤ x ≤ 1 to determine the optimal composition range for ferroelectric properties.
- Open Access
- 11 December 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (3) , 1746-1752
An energy harvester based on UV-polymerized short-alkyl-chain-modified [DBU][TFSI] ionic liquid electrets
Three short-alkyl-chain-modified [DBU][TFSI] ionic liquids (ILs) were synthesized and utilized in electrets. The electrets were prepared by mixing a UV-curable polymer with the ionic liquids followed by polymerization while applying an external electric field, thus forming spatially separated anions and cations in the proximity of opposing surfaces of the composite slabs. The immobilized surplus surface charge was measured by periodically engaging the electret with a metal counter electrode plate and detecting the displacement current using a charge amplifier. The results show that electrets based on polymerized [DBU][TFSI] ILs have a separated surface charge density of up to 64 nC × cm−2, which equals an energy harvesting density of 7.0 nJ × cm−2. Control measurements repeated after a few days to assess the stability and reproducibility of the systems showed that while charge separation reverses over time to some extent, the polymerized ionic liquid samples are resilient to exposure to atmospheric conditions and could be utilized in this type of energy harvesting scheme.
- 11 December 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (3) , 1746-1752
Open AccessAn energy harvester based on UV-polymerized short-alkyl-chain-modified [DBU][TFSI] ionic liquid electrets
Three short-alkyl-chain-modified [DBU][TFSI] ionic liquids (ILs) were synthesized and utilized in electrets. The electrets were prepared by mixing a UV-curable polymer with the ionic liquids followed by polymerization while applying an external electric field, thus forming spatially separated anions and cations in the proximity of opposing surfaces of the composite slabs. The immobilized surplus surface charge was measured by periodically engaging the electret with a metal counter electrode plate and detecting the displacement current using a charge amplifier. The results show that electrets based on polymerized [DBU][TFSI] ILs have a separated surface charge density of up to 64 nC × cm−2, which equals an energy harvesting density of 7.0 nJ × cm−2. Control measurements repeated after a few days to assess the stability and reproducibility of the systems showed that while charge separation reverses over time to some extent, the polymerized ionic liquid samples are resilient to exposure to atmospheric conditions and could be utilized in this type of energy harvesting scheme.
- Open Access
- 27 August 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 245, 110235
Corrigendum to “High performance piezoelectric composite fabricated at ultra low temperature” [Compos. Part B Eng. 229 (2022) 109486]
- 27 August 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 245, 110235
Open AccessCorrigendum to “High performance piezoelectric composite fabricated at ultra low temperature” [Compos. Part B Eng. 229 (2022) 109486]
- Open Access
- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 052903
Enhanced piezoelectric performance of ceramic-polymer composite cantilevers with thin metal substrates
In this work, the electromechanical properties of a lead zirconate titanate-poly(vinylidenefluoride-trifluoroethylene) ceramic-polymer composite on thin brass and steel substrates were investigated. Samples were stencil printed on metal foils and cured at 120 °C. The effective transverse piezoelectric coefficient (d31eff) was calculated by utilizing the converse piezoelectric effect and measuring the displacement of a cantilever sample’s tip in an electric field. Interestingly, the results showed improved piezoelectric properties with the stiffer steel substrate samples. The highest d31eff achieved was about −22 pm/V, which was 29% higher than in samples printed on brass foil (−17 pm/V). Both are substantially higher compared to the coefficients reported with similar ceramic-polymer composites on polymer substrates. The improvement is suggested to originate from the prevention of buckling effects and more effective bending deformation, while the structure remained flexible. Due to the high effective values of d31 and g31, the developed material and cantilever structures are feasible for both sensor and energy harvesting applications.
- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 052903
Open AccessEnhanced piezoelectric performance of ceramic-polymer composite cantilevers with thin metal substrates
In this work, the electromechanical properties of a lead zirconate titanate-poly(vinylidenefluoride-trifluoroethylene) ceramic-polymer composite on thin brass and steel substrates were investigated. Samples were stencil printed on metal foils and cured at 120 °C. The effective transverse piezoelectric coefficient (d31eff) was calculated by utilizing the converse piezoelectric effect and measuring the displacement of a cantilever sample’s tip in an electric field. Interestingly, the results showed improved piezoelectric properties with the stiffer steel substrate samples. The highest d31eff achieved was about −22 pm/V, which was 29% higher than in samples printed on brass foil (−17 pm/V). Both are substantially higher compared to the coefficients reported with similar ceramic-polymer composites on polymer substrates. The improvement is suggested to originate from the prevention of buckling effects and more effective bending deformation, while the structure remained flexible. Due to the high effective values of d31 and g31, the developed material and cantilever structures are feasible for both sensor and energy harvesting applications.
- Open Access
- 1 January 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 229
High performance piezoelectric composite fabricated at ultra low temperature
- 1 January 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 229
Open AccessHigh performance piezoelectric composite fabricated at ultra low temperature
- Open Access
- 1 October 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (13) , 6790
Corrigendum to “Upside - Down composites: Fabricating piezoceramics at room temperature” [J. Eur. Ceram. Soc. 39 (September (11)) (2019) 3301–3306]
- 1 October 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (13) , 6790
Open AccessCorrigendum to “Upside - Down composites: Fabricating piezoceramics at room temperature” [J. Eur. Ceram. Soc. 39 (September (11)) (2019) 3301–3306]
- Open Access
- 1 September 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (11) , 3301-3306
Upside - down composites: Fabricating piezoceramics at room temperature
- 1 September 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (11) , 3301-3306
Open AccessUpside - down composites: Fabricating piezoceramics at room temperature