Okiemute Roland Ogirigbo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Okiemute Roland Ogirigbo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Leon Black
School of Civil Engineering, University of Leeds, Leeds, UK
4 shared publications - Daniel Usidamen
Department of Civil Engineering University of Benin Benin City Edo State Nigeria
3 shared publications - Ebuka Nwankwo
University of Benin
3 shared publications - Edidiong Eseme Ambrose
Department of Civil Engineering, Akwa Ibom State University, Ikot Akpaden 534111, Nigeria
3 shared publications - Ifiok Edem Ekop
University of Uyo
2 shared publications - Iziengbe Inerhunwa
University of Benin
2 shared publications
Latest Publications
- Open Access
- 14 January 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 124 (1) , 1
Compressive Strength, Density, and Setting Time of Concrete Blended with Rice Husk Ash
This study investigated the effects of incorporating rice husk ash (RHA) as a partial replacement for cement on the properties of concrete. To determine the optimal replacement level, RHA was used to replace cement in varying proportions, ranging from 0% to 25% in 5% increments. The mix with 0% RHA served as the control. The properties evaluated included setting time, density, and compressive strength. The results revealed that blending RHA with cement increased the initial setting time. This was attributed to the lower calcium oxide (CaO) content of RHA, which slows early-age hydration reactions. Conversely, the final setting time was reduced due to the pozzolanic activity of RHA, which enhances later-stage reactions. Additionally, the inclusion of RHA resulted in a decrease in concrete density, owing to its lower specific gravity and bulk density compared to Portland cement. Despite this, RHA-modified specimens exhibited higher compressive strengths than the control specimens. This strength enhancement was linked to the formation of additional calcium–silicate–hydrate (C-S-H) gel due to the pozzolanic reaction between amorphous silica in RHA and calcium hydroxide (Ca(OH)2) from hydration reaction. The gel fills concrete voids at the microstructural level, producing a denser and more compact concrete matrix. Based on the balance between strength and durability, the optimal RHA replacement level was identified as 10%.
- 14 January 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 124 (1) , 1
Open AccessCompressive Strength, Density, and Setting Time of Concrete Blended with Rice Husk Ash
This study investigated the effects of incorporating rice husk ash (RHA) as a partial replacement for cement on the properties of concrete. To determine the optimal replacement level, RHA was used to replace cement in varying proportions, ranging from 0% to 25% in 5% increments. The mix with 0% RHA served as the control. The properties evaluated included setting time, density, and compressive strength. The results revealed that blending RHA with cement increased the initial setting time. This was attributed to the lower calcium oxide (CaO) content of RHA, which slows early-age hydration reactions. Conversely, the final setting time was reduced due to the pozzolanic activity of RHA, which enhances later-stage reactions. Additionally, the inclusion of RHA resulted in a decrease in concrete density, owing to its lower specific gravity and bulk density compared to Portland cement. Despite this, RHA-modified specimens exhibited higher compressive strengths than the control specimens. This strength enhancement was linked to the formation of additional calcium–silicate–hydrate (C-S-H) gel due to the pozzolanic reaction between amorphous silica in RHA and calcium hydroxide (Ca(OH)2) from hydration reaction. The gel fills concrete voids at the microstructural level, producing a denser and more compact concrete matrix. Based on the balance between strength and durability, the optimal RHA replacement level was identified as 10%.
- Open Access
- 19 December 2025
- Published by MDPI AG in Construction Materials
- Vol. 6 (1) , 1
Beyond Burnt Bricks: Reassessing Otukpo Soil for Sustainable Construction Applications
The Otukpo Burnt Brick Factory has remained dormant for more than three decades despite repeated government interventions. In this context, the present study investigates the suitability of soils from Otukpo, Benue State, Nigeria, for unfired brick production and as supplementary cementitious materials (SCMs). Four representative samples (OT1–OT4) were subjected to X-ray fluorescence (XRF), thermogravimetric analysis (TGA), particle size distribution (PSD), X-ray diffraction (XRD), unconfined compressive strength (UCS), cube strength, shrinkage, and water absorption tests. The results revealed high reactive oxide contents (SiO2 + Al2O3 + Fe2O3 > 93%) with low SO3 and moderate loss on ignition (~6%), thus indicating strong pozzolanic potential. PSD residues on the 45 µm sieve ranged from 6.8 to 17%, which is well below the ASTM C618 limit of 34%. XRD confirmed quartz and kaolinite as dominant phases. Strength activity indices showed that only OT3 and OT4 exceeded Nigerian (NIS 693:2007) and Indian (IS 1725:2023) standards when stabilized with 5 wt.% cement or sodium hydroxide; while OT1 and OT2 were below these thresholds. Water absorption values for OT3 (18.69%) and OT4 (19.04%) marginally satisfied Indian standards but failed Nigerian requirements, which is reflective of high porosity. Linear shrinkage (~14%) met IS 1498 marginally, and pH values (6.14–6.34) were consistent with lateritic soils. Overall, OT3 and OT4 demonstrated promise for low-energy SCMs and unfired brick applications, though they must be restricted to non-load-bearing uses unless further stabilization is applied.
- 19 December 2025
- Published by MDPI AG in Construction Materials
- Vol. 6 (1) , 1
Open AccessBeyond Burnt Bricks: Reassessing Otukpo Soil for Sustainable Construction Applications
The Otukpo Burnt Brick Factory has remained dormant for more than three decades despite repeated government interventions. In this context, the present study investigates the suitability of soils from Otukpo, Benue State, Nigeria, for unfired brick production and as supplementary cementitious materials (SCMs). Four representative samples (OT1–OT4) were subjected to X-ray fluorescence (XRF), thermogravimetric analysis (TGA), particle size distribution (PSD), X-ray diffraction (XRD), unconfined compressive strength (UCS), cube strength, shrinkage, and water absorption tests. The results revealed high reactive oxide contents (SiO2 + Al2O3 + Fe2O3 > 93%) with low SO3 and moderate loss on ignition (~6%), thus indicating strong pozzolanic potential. PSD residues on the 45 µm sieve ranged from 6.8 to 17%, which is well below the ASTM C618 limit of 34%. XRD confirmed quartz and kaolinite as dominant phases. Strength activity indices showed that only OT3 and OT4 exceeded Nigerian (NIS 693:2007) and Indian (IS 1725:2023) standards when stabilized with 5 wt.% cement or sodium hydroxide; while OT1 and OT2 were below these thresholds. Water absorption values for OT3 (18.69%) and OT4 (19.04%) marginally satisfied Indian standards but failed Nigerian requirements, which is reflective of high porosity. Linear shrinkage (~14%) met IS 1498 marginally, and pH values (6.14–6.34) were consistent with lateritic soils. Overall, OT3 and OT4 demonstrated promise for low-energy SCMs and unfired brick applications, though they must be restricted to non-load-bearing uses unless further stabilization is applied.
- Open Access
- 6 November 2025
- Published by MDPI AG in Preprints.org
Beyond Burnt Bricks: Reassessing Otukpo Soil for Sustainable Construction Applications
The Otukpo Burnt Brick Factory has remained inactive for over three decades despite repeated government efforts to revive it. Given the abundance of clay-rich soils in the region and the growing need for sustainable, low-cost building materials, this study explores the potential of Otukpo soils for uncalcined brick production and use as supplementary cementitious materials (SCMs). Four representative samples (OT1–OT4) were characterized through mechanical, chemical, and mineralogical tests aligned with international standards for natural pozzolans. All samples exhibited high oxide contents (SiO₂ + Al₂O₃ + Fe₂O₃ > 93 %), low SO₃ and loss-on-ignition (~6 %), and adequate fineness (13–17 % retained on a 45 µm sieve), suggestive of favorable pozzolanic properties. Strength Activity Indices (SAI) based on unconfined compressive strength (UCS) and cube strength showed that OT3 and OT4 exceeded 100% of the NIS 87:2007 (≥2500 kPa at 28 days) threshold at 56 days with 5 wt.% sodium hydroxide and cement activation. Both also surpassed the NBC’s 14-day cube strength requirement (≥1600 kPa) and maintained water absorption below the 20 % limit for bricks. Unstabilized samples collapsed upon immersion, indicating excessive porosity/poor durability without enhancements. These findings strongly suggest that the Otukpo soils, particularly OT3 and OT4, are suitable for low-energy brick and SCM production.
- 6 November 2025
- Published by MDPI AG in Preprints.org
Open AccessBeyond Burnt Bricks: Reassessing Otukpo Soil for Sustainable Construction Applications
The Otukpo Burnt Brick Factory has remained inactive for over three decades despite repeated government efforts to revive it. Given the abundance of clay-rich soils in the region and the growing need for sustainable, low-cost building materials, this study explores the potential of Otukpo soils for uncalcined brick production and use as supplementary cementitious materials (SCMs). Four representative samples (OT1–OT4) were characterized through mechanical, chemical, and mineralogical tests aligned with international standards for natural pozzolans. All samples exhibited high oxide contents (SiO₂ + Al₂O₃ + Fe₂O₃ > 93 %), low SO₃ and loss-on-ignition (~6 %), and adequate fineness (13–17 % retained on a 45 µm sieve), suggestive of favorable pozzolanic properties. Strength Activity Indices (SAI) based on unconfined compressive strength (UCS) and cube strength showed that OT3 and OT4 exceeded 100% of the NIS 87:2007 (≥2500 kPa at 28 days) threshold at 56 days with 5 wt.% sodium hydroxide and cement activation. Both also surpassed the NBC’s 14-day cube strength requirement (≥1600 kPa) and maintained water absorption below the 20 % limit for bricks. Unstabilized samples collapsed upon immersion, indicating excessive porosity/poor durability without enhancements. These findings strongly suggest that the Otukpo soils, particularly OT3 and OT4, are suitable for low-energy brick and SCM production.
- Open Access
- 29 July 2025
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 29 (7) , 2229-2239
Mechanical Properties and Flexural Behaviour of Bamboo-Reinforced Concrete Beams
The construction industry urgently needs sustainable alternatives to conventional materials due to environmental concerns. Bamboo's quick growth and renewable qualities make it a promising choice for reinforcing concrete structures. Hence, the objective of this is to evaluate the mechanical properties and flexural behaviour of bamboo reinforced concrete (BRC) beams using appropriate standard methods. Results indicated that bamboo specimens without nodes exhibited better mechanical properties compared to those with nodes. Flexural tests revealed SRC beams retained 32% of load-carrying capacity after the first crack, while BRC beams retained 14%, and HYB-1 and HYB-2 beams retained 23% and 30%, respectively. The average flexural strength for BRC beams was 82.8% lower than SRC beams, while HYB-1 and HYB-2 showed reductions of 16.9% and 76.1%. The energy absorption capacity of HYB-1 beams was close to SRC beams, with only a 29.1% reduction. These findings suggest that hybrid configurations, particularly HYB-1, balance structural strength and sustainability.
- 29 July 2025
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 29 (7) , 2229-2239
Open AccessMechanical Properties and Flexural Behaviour of Bamboo-Reinforced Concrete Beams
The construction industry urgently needs sustainable alternatives to conventional materials due to environmental concerns. Bamboo's quick growth and renewable qualities make it a promising choice for reinforcing concrete structures. Hence, the objective of this is to evaluate the mechanical properties and flexural behaviour of bamboo reinforced concrete (BRC) beams using appropriate standard methods. Results indicated that bamboo specimens without nodes exhibited better mechanical properties compared to those with nodes. Flexural tests revealed SRC beams retained 32% of load-carrying capacity after the first crack, while BRC beams retained 14%, and HYB-1 and HYB-2 beams retained 23% and 30%, respectively. The average flexural strength for BRC beams was 82.8% lower than SRC beams, while HYB-1 and HYB-2 showed reductions of 16.9% and 76.1%. The energy absorption capacity of HYB-1 beams was close to SRC beams, with only a 29.1% reduction. These findings suggest that hybrid configurations, particularly HYB-1, balance structural strength and sustainability.
- Open Access
- 8 July 2025
- Published by National Institute of Professional Engineers and Scientists in NIPES - Journal of Science and Technology Research
- Vol. 7 (3) , 399-402
Effects of Relative Humidity on the Mechanical Properties of Rice Husk Ash Concrete
This study investigates the influence of environmental relative humidity (RH) on the mechanical properties and durability behaviour of rice husk ash (RHA) concrete. Concrete cubes were produced with 0%, 5%, 10%, and 15% RHA as partial replacement for Portland limestone cement and cured under three simulated RH conditions (31%, 51%, and 78%) representing typical Nigerian climates. Each test—compressive strength, ultrasonic pulse velocity (UPV), and water absorption—was conducted in triplicate at curing ages of 7, 14, 28, and 91 days. Statistical analysis (ANOVA) and error bars were used to establish the significance of RH levels and RHA percentages. Results show that 5% RHA at 78% RH achieved optimal performance, meeting the Grade 25 concrete target. Strength and UPV decreased at lower RH levels and with higher RHA percentages. Water absorption increased with RHA content, especially under 78% RH. These findings provide valuable insights for construction in tropical climates and promote sustainable use of cement through RHA utilization.
- 8 July 2025
- Published by National Institute of Professional Engineers and Scientists in NIPES - Journal of Science and Technology Research
- Vol. 7 (3) , 399-402
Open AccessEffects of Relative Humidity on the Mechanical Properties of Rice Husk Ash Concrete
This study investigates the influence of environmental relative humidity (RH) on the mechanical properties and durability behaviour of rice husk ash (RHA) concrete. Concrete cubes were produced with 0%, 5%, 10%, and 15% RHA as partial replacement for Portland limestone cement and cured under three simulated RH conditions (31%, 51%, and 78%) representing typical Nigerian climates. Each test—compressive strength, ultrasonic pulse velocity (UPV), and water absorption—was conducted in triplicate at curing ages of 7, 14, 28, and 91 days. Statistical analysis (ANOVA) and error bars were used to establish the significance of RH levels and RHA percentages. Results show that 5% RHA at 78% RH achieved optimal performance, meeting the Grade 25 concrete target. Strength and UPV decreased at lower RH levels and with higher RHA percentages. Water absorption increased with RHA content, especially under 78% RH. These findings provide valuable insights for construction in tropical climates and promote sustainable use of cement through RHA utilization.
- Open Access
- 19 December 2024
- Published by Springer Nature in Discover Civil Engineering
- Vol. 1 (1) , 1-22
An experimental and numerical evaluation of the structural performance of bamboo-reinforced concrete beams
- 19 December 2024
- Published by Springer Nature in Discover Civil Engineering
- Vol. 1 (1) , 1-22
Open AccessAn experimental and numerical evaluation of the structural performance of bamboo-reinforced concrete beams
- Open Access
- 26 November 2024
- Published by Springer Nature in Research Square
An Experimental and Numerical Evaluation of the Structural performance of Bamboo-Reinforced Concrete Beams
The global shift toward sustainable construction calls for eco-friendly alternatives to traditional materials. While steel reinforcement in concrete offers high strength and durability, it has significant environmental and economic drawbacks. Bamboo, a fast-growing and renewable material, is a low-cost, eco-friendly option, but concerns about its structural performance have hindered its widespread use. This study examines the structural performance of concrete beams reinforced with steel (SRC), bamboo (BRC), and hybrid steel-bamboo combinations (HYB-1 and HYB-2). It assesses ultimate failure load, load-deflection curves, failure modes, and crack patterns to explore their viability as sustainable alternatives. Beams measuring 150×150×750 mm were tested experimentally and simulated using ABAQUS software under three-point bending. SRC beams had the highest ultimate failure load (104.67 kN) and deflection (8.6 mm). BRC beams had the lowest failure load (17.97 kN), a decrease of 82.9%. HYB-1 and HYB-2 showed intermediate loads of 87.25 kN and 24.99 kN, respectively. Deflection in BRC beams was the least (3.0 mm), while HYB-1 and HYB-2 showed deflections of 7.4 mm and 5.6 mm. Finite element analysis (FEA) closely matched experimental results, with an average difference of 7.44%, validating the accuracy of the modeling.
- 26 November 2024
- Published by Springer Nature in Research Square
Open AccessAn Experimental and Numerical Evaluation of the Structural performance of Bamboo-Reinforced Concrete Beams
The global shift toward sustainable construction calls for eco-friendly alternatives to traditional materials. While steel reinforcement in concrete offers high strength and durability, it has significant environmental and economic drawbacks. Bamboo, a fast-growing and renewable material, is a low-cost, eco-friendly option, but concerns about its structural performance have hindered its widespread use. This study examines the structural performance of concrete beams reinforced with steel (SRC), bamboo (BRC), and hybrid steel-bamboo combinations (HYB-1 and HYB-2). It assesses ultimate failure load, load-deflection curves, failure modes, and crack patterns to explore their viability as sustainable alternatives. Beams measuring 150×150×750 mm were tested experimentally and simulated using ABAQUS software under three-point bending. SRC beams had the highest ultimate failure load (104.67 kN) and deflection (8.6 mm). BRC beams had the lowest failure load (17.97 kN), a decrease of 82.9%. HYB-1 and HYB-2 showed intermediate loads of 87.25 kN and 24.99 kN, respectively. Deflection in BRC beams was the least (3.0 mm), while HYB-1 and HYB-2 showed deflections of 7.4 mm and 5.6 mm. Finite element analysis (FEA) closely matched experimental results, with an average difference of 7.44%, validating the accuracy of the modeling.
- 5 August 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 19 (2) , 369-380
Compressive Strength, Workability, and Durability Performance of Concrete Incorporating Waste Ceramic Tile as Fine Aggregate
- 5 August 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 19 (2) , 369-380
Compressive Strength, Workability, and Durability Performance of Concrete Incorporating Waste Ceramic Tile as Fine Aggregate
- Open Access
- 2 October 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (9) , 2003-2008
Performance Evaluation of Rice Husk Ash as Partial Replacement of Cement in Concrete in a Marine Environment at Escravos River, Niger Delta Area, Nigeria
Cement has proven to cause environmental problems during its production and to be a relatively high-cost material in concrete production. Environmentally friendly, alternative binders like Rice Husk Ash (RHA) have recently been brought to bear. Therefore, the objective of this paper is to evaluate the performance of RHA (under controlled temperature and burning time) as a partial (10% and 20%) replacement of cement in concrete in a marine environment at Escravos River, Niger Delta Area, Nigeria. Concrete samples prepared with the 10% and 20% RHA in the laboratory were exposed to brackish water samples from the Escravos River, at 3 days, 7 days, 28 days and 90 days and the results compared with that of PLC concrete cast. Data obtained show that the workability of fresh concrete reduced with increase in RHA and further reduced, mixing with salt water. RHA contributed positively to the setting time of the concrete as it increased the initial setting time and reduced final setting time. 10%RHA concrete performed best under all conditions, with about 10% increase in strength. Further increase led to a slight decline in strength. As the amount of RHA increased, the ability of the concrete to resist chloride penetration, increased, with lesser average penetration depth. 10%RHA concrete showed the strongest rebar-concrete bond. 10% RHA is optimum for partial replacement of cement in concrete in marine environment, as it enhances the performance of the concrete.
- 2 October 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (9) , 2003-2008
Open AccessPerformance Evaluation of Rice Husk Ash as Partial Replacement of Cement in Concrete in a Marine Environment at Escravos River, Niger Delta Area, Nigeria
Cement has proven to cause environmental problems during its production and to be a relatively high-cost material in concrete production. Environmentally friendly, alternative binders like Rice Husk Ash (RHA) have recently been brought to bear. Therefore, the objective of this paper is to evaluate the performance of RHA (under controlled temperature and burning time) as a partial (10% and 20%) replacement of cement in concrete in a marine environment at Escravos River, Niger Delta Area, Nigeria. Concrete samples prepared with the 10% and 20% RHA in the laboratory were exposed to brackish water samples from the Escravos River, at 3 days, 7 days, 28 days and 90 days and the results compared with that of PLC concrete cast. Data obtained show that the workability of fresh concrete reduced with increase in RHA and further reduced, mixing with salt water. RHA contributed positively to the setting time of the concrete as it increased the initial setting time and reduced final setting time. 10%RHA concrete performed best under all conditions, with about 10% increase in strength. Further increase led to a slight decline in strength. As the amount of RHA increased, the ability of the concrete to resist chloride penetration, increased, with lesser average penetration depth. 10%RHA concrete showed the strongest rebar-concrete bond. 10% RHA is optimum for partial replacement of cement in concrete in marine environment, as it enhances the performance of the concrete.
- Open Access
- 31 March 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (3) , 465-472
Compressive Strength and Resistance to Sodium Sulphate Attack of Concrete Incorporated with Fine Aggregate Recycled Ceramic Tiles
In this experimental study, compressive strength and resistance to sodium sulphate attack of concrete incorporating recycled ceramic tiles (RCT) as fine aggregate were investigated. RCT was used as partial replacement for river sand at four levels (0%, 33%, 66%, 100%). Samples for sulphate resistance tests were immersed in 5% Na2SO4 solution for 180 days after they had been cured under water for 28 days, and were monitored for change in physical appearance, mass change and loss of compressive strength. From experimental results, RCT was found to be capable of producing light weight concrete compared to river sand. The results showed increase in compressive strength as the level of RCT content increased. On resistance to sulphate attack, sodium sulphate seems not to attack C-S-H bond which is produced in excess in RCT concrete, rather it attacks calcium hydroxide and calcium aluminate which are produced in equal amounts for both RCT and control samples. Hence, RCT might not play much direct role in concrete’s resistance to strength loss due to sulphate attack. However, the residual compressive strength of the RCT samples after the attack was seen to be much higher than that of the control samples because of their initial higher strength before the attack. This shows that RCT can improve the properties of concrete when incorporated as fine aggregates.
- 31 March 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (3) , 465-472
Open AccessCompressive Strength and Resistance to Sodium Sulphate Attack of Concrete Incorporated with Fine Aggregate Recycled Ceramic Tiles
In this experimental study, compressive strength and resistance to sodium sulphate attack of concrete incorporating recycled ceramic tiles (RCT) as fine aggregate were investigated. RCT was used as partial replacement for river sand at four levels (0%, 33%, 66%, 100%). Samples for sulphate resistance tests were immersed in 5% Na2SO4 solution for 180 days after they had been cured under water for 28 days, and were monitored for change in physical appearance, mass change and loss of compressive strength. From experimental results, RCT was found to be capable of producing light weight concrete compared to river sand. The results showed increase in compressive strength as the level of RCT content increased. On resistance to sulphate attack, sodium sulphate seems not to attack C-S-H bond which is produced in excess in RCT concrete, rather it attacks calcium hydroxide and calcium aluminate which are produced in equal amounts for both RCT and control samples. Hence, RCT might not play much direct role in concrete’s resistance to strength loss due to sulphate attack. However, the residual compressive strength of the RCT samples after the attack was seen to be much higher than that of the control samples because of their initial higher strength before the attack. This shows that RCT can improve the properties of concrete when incorporated as fine aggregates.