ENEbuka Nwankwo

Ebuka Nwankwo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ebuka Nwankwo has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Multiscale homogenisation and quasi-static characterisation of kenaf 2D woven fabric composites: Foundational insights for future ballistic modelling

    by Osarobo Ighodaro, Henry Egware, Ebuka Nwankwo, Efe Orumwense, Collins Kwasi-Effah, Musa Abdulazeez, Amune Joseph, Okpako Ogheneochuko, Esimike Thelma, Daniel Okene, et al.


  • Open Access

    Mechanical Properties and Flexural Behaviour of Bamboo-Reinforced Concrete Beams

    by S. A. Adegbemileke, D. Usidamen, O. R. Ogirigbo, E. Nwankwo

    The construction industry urgently needs sustainable alternatives to conventional materials due to environmental concerns. Bamboo's quick growth and renewable qualities make it a promising choice for reinforcing concrete structures. Hence, the objective of this is to evaluate the mechanical properties and flexural behaviour of bamboo reinforced concrete (BRC) beams using appropriate standard methods. Results indicated that bamboo specimens without nodes exhibited better mechanical properties compared to those with nodes. Flexural tests revealed SRC beams retained 32% of load-carrying capacity after the first crack, while BRC beams retained 14%, and HYB-1 and HYB-2 beams retained 23% and 30%, respectively. The average flexural strength for BRC beams was 82.8% lower than SRC beams, while HYB-1 and HYB-2 showed reductions of 16.9% and 76.1%. The energy absorption capacity of HYB-1 beams was close to SRC beams, with only a 29.1% reduction. These findings suggest that hybrid configurations, particularly HYB-1, balance structural strength and sustainability.

  • Open Access

    An Experimental and Numerical Evaluation of the Structural performance of Bamboo-Reinforced Concrete Beams

    by Daniel Usidamen, Okiemute Roland Ogirigbo, Ebuka Nwankwo

    The global shift toward sustainable construction calls for eco-friendly alternatives to traditional materials. While steel reinforcement in concrete offers high strength and durability, it has significant environmental and economic drawbacks. Bamboo, a fast-growing and renewable material, is a low-cost, eco-friendly option, but concerns about its structural performance have hindered its widespread use. This study examines the structural performance of concrete beams reinforced with steel (SRC), bamboo (BRC), and hybrid steel-bamboo combinations (HYB-1 and HYB-2). It assesses ultimate failure load, load-deflection curves, failure modes, and crack patterns to explore their viability as sustainable alternatives. Beams measuring 150×150×750 mm were tested experimentally and simulated using ABAQUS software under three-point bending. SRC beams had the highest ultimate failure load (104.67 kN) and deflection (8.6 mm). BRC beams had the lowest failure load (17.97 kN), a decrease of 82.9%. HYB-1 and HYB-2 showed intermediate loads of 87.25 kN and 24.99 kN, respectively. Deflection in BRC beams was the least (3.0 mm), while HYB-1 and HYB-2 showed deflections of 7.4 mm and 5.6 mm. Finite element analysis (FEA) closely matched experimental results, with an average difference of 7.44%, validating the accuracy of the modeling.

  • Open Access

    Theoretical and experimental assessment of the effect of adhesive bond thickness on the flexural capacity of CFRP strengthened beams

    by Ebuka Nwankwo, TrustGod John

    Carbon Fiber Reinforced Polymer (CFRP) is a material of choice in the structural strengthening of reinforced concrete (RC) elements. In order to strengthen RC elements, CRFP is bonded externally to RC elements using adhesives. This paper investigates the effect of varying adhesive bond thickness on the moment capacity of CFRP strengthened RC beams in flexure. Thirty-eight (38) Reinforced concrete beams (1.2m length) were cast in the laboratory and their failure loads and corresponding moment capacities obtained when the adhesive bond thickness between the CFRP wraps and RC beams were varied. This paper examines the comparison between flexural moment capacities obtained experimentally and the predicted moment capacities using a theoretical procedure set out in AC440-2R-17 after structural strengthening with CFRP. It was observed that the adhesive thickness had a significant effect on the flexural capacity of strengthened beams. As the adhesive thickness increased beyond certain thresholds, the flexural capacity of strengthened beams reduced. At the optimum adhesive thickness threshold, the ACI 440-2r-17 procedures could predict to high accuracy the moment capacities of strengthened beams.

  • Open Access

    Correlation between Pile Displacement from Pile Load Tests and FE Modelling: Case Study of Piles in Cawthorne Channel Area in Nigeria: Case Study of Piles in Cawthorne Channel Area in Nigeria

    by Ebuka Nwankwo

    Pile load static tests are used to confirm that a pile would not exceed a prescribed displacement at service or ultimate limit load. In this work, 600mm diameter steel piles were driven to 30m depths at the project site in the Niger Delta region of Nigeria. The relationship between pile displacements obtained from field pile load tests on these driven piles and those obtained from a finite element (FE) program, PileAXL, was studied. It was observed that for loads lower than the elastic limit of the soils at the pile toe, the FE program was able to accurately predict the displacements obtained from pile load tests. However, as the test loads on piles increased, the FE program was not able to accurately predict the displacements obtained from the pile load tests. This suggests that as significant plasticity sets in the end-bearing pile spring in the FE program, a more rigorous end bearing nonlinear spring would be required to model the load-displacement behavior of piles. This paper aims at presenting a technical reference to show that pile load test results can be easily validated using simplified FE models at low service loads using simplified nonlinear springs to model pile shaft interaction and end-bearing displacements.

  • Open Access

    EFFECT OF BOND SURFACE AREA ON THE SHEAR STRENGTH OF CARBON FIBRE REINFORCED POLYMER (CFRP) STRENGTHENED REINFORCED CONCRETE BEAMS

    by A. T. John, S. O. Osuji, E. Nwankwo

    The use of carbon fiber reinforced polymer (CFRP) for shear strengthening of reinforced concrete (RC) elements has grown significantly over the last few decades. The effectiveness of a CFRP strengthened system depends primarily on the bond strength between the CFRP and RC substrate. Since cost of CFRP and bond materials (epoxy adhesive) is relatively high, it is important to reduce CFRP bond surface area to RC when carrying out structural strengthening. This paper reports the effect of bond surface area on the shear strength of RC beams externally bonded with CFRP. Seven RC beams were investigated. One of the beam specimens was not strengthened and was used as a reference. The remaining six beams were strengthened with 200 g/m2 and 300 g/m2 CFRP fabrics with three different bond surface areas, i.e., 0.15 m2, 0.2 m2 and 0.25 m2 in a U-wrap configuration. Static bending tests were performed on all the beams. Results show that the CFRP's contribution to shear strength increases as the bond surface area increases. Results also show that the shear strength of the RC beam was increased by 45% due to the presence of CFRP. Fundamentally, this work presents a parametric study to guide engineers on how shear strength and corresponding ductility of beams can be increased with an optimal configuration of the bond surface between CFRP and RC elements. An optimal and cost-effective configuration is proposed for carrying out nominal shear strengthening of RC elements after construction, especially in cases where the construction engineer has concerns about the shear stirrups provided before casting.


  • Open Access

    Effect of Local Binary Mixtures of Coarse Aggregates on the Compressive Properties of Concrete

    by O. K. Eze, E. Nwankwo

    Aggregates, though considered inert, are the primary components that define concrete’s thermal and elastic properties. It has been shown that factors such as maximum aggregate size, grading, shape, strength, water absorption capacity of coarse aggregates affect the properties of concrete. However, improper grading of coarse aggregate could have adverse effect on the amount of cement and water requirement for concrete production. Thus, impacting on the workability, pump-ability and durability of concrete. By maintaining a slump of 50 mm, the effect of varying sizes of coarse aggregates – 10 mm, 14 mm, 20 mm, and combination of these sizes – on the mechanical properties of concrete was obtained. Aggregates, which were used in this work, were sourced from quarries located in Auchi area of Edo State and had impact values between 16% and 28%. It was observed that the higher the coarse aggregate sizes the lower the water – cement (w/c) ratio required to obtain adequate workability. Also, the compressive strength of concrete was observed to be a function of the size of the coarse aggregates used in the concrete mix. It was observed that concrete made with equal proportions of 10 mm and 14 mm coarse aggregate had lower strengths compared to concrete made with 14 mm and 20 mm aggregates. This implies that combination of large sizes of aggregates produced stronger concrete when compared to combinations of smaller sizes of aggregates. It was also observed that density of concrete increased with increasing size of aggregates.

  • Open Access

    Strength and Workability Assessment of Concrete Produced by Partial Replacement of Cement with Waste Clay Bricks

    by Ebuka Nwankwo, A. T. John

    The use of waste clay bricks—which are abundant in the Niger Delta Region of Nigeria – as supplementary cementitious material, would enable the construction industry utilize thousands of tons of brick blocks that would have ended up as waste or landfill materials. This paper establishes the pozzolanic properties of these waste clay bricks in terms of strength and workability. Waste clay brick powders are introduced as partial replacement for cement in this research. All tests were done in accordance with relevant British Standards. It was observed that waste clay brick, as an admixture, increases the workability and consistency of fresh concrete. Also, an 11 percent increase in compressive strength was observed with a 10 percent partial replacement of cement with waste clay brick powders. An equation is developed to capture the marginal increase in compressive strength of concrete produced with waste clay bricks, even after 28 days, for a 10% partial replacement of cement.