MIMuhammad Remanul Islam

Muhammad Remanul Islam

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Muhammad Remanul Islam has a total of 123 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Autonomous Corrosion‐Self‐Healing Coatings of Microencapsulated Soybean Oil on Mild Steel

    by Ahmad Syahmi Mazelan, Noor Azlina Kamaruding, Mohamad Shahrul Effendy Kosnan, Nurul Syazmeen Saiful Rijal, Muhammad Remanul Islam, Shahrulzaman Shaharuddin

    In the oil and gas industry, the failure of protective coatings can cause material degradation, which can be hazardous for safety, asset integrity and environmental health. In this study, the use of an autonomous (self‐healing) microencapsulated corrosion coating, using microencapsulated soybean oil (SBO), was explored and the protection was tested for mild steel immersed in 3.5wt.% NaCl solution. The coating formulation consisted of emulsion of soybean oil, EMA, resorcinol, ammonium chloride, 1‐octanol, urea, 37wt.% aqueous formaldehyde solution and distilled water. The electrochemical impedance spectroscopy (EIS) results showed that the corrosion resistance of the mild steel was greatly improved after being coated with SBO, as compared to the control. The best results have been achieved with the 30 mL SBO coating, with the acceptable impedance response and the lowest corrosion current density. A uniform and protective coating layer that has enhanced corrosion damage resistance has been confirmed by optical microscopy, scanning electron microscopy (SEM) and energy‐dispersive x‐ray spectroscopy (EDX). The FT‐IR data confirmed the inclusion of the soybean oil in the coating and electrochemical tests showed the enhancement of the corrosion protection performance with the concentration of the soybean oil. Based on the results of this study, it appears that the coatings prepared using microencapsulated soybean oil are suitable self‐healing corrosion protection systems, which may be more environmentally friendly and sustainable for mild steel.

  • A review of recent developments in polymeric materials for battery energy storage

    by Maryam Firouzi, Muhammad Remanul Islam, Izuan Nasib, Richard Davis, Weiguo Xie, Sam Toan, Sairul Izwan Bin Safie, Ahmad Naim Ahmad Yahaya

    This review explores the innovative role of polymer electrolytes in energy storage systems, emphasizing their characteristics, fabrication methods, and practical applications in advanced electrochemistry. It begins by outlining various types of polymeric material, including conductive polymers, redox-active polymers, and polymer electrolytes, that improve the lifetime, efficiency, and capacity of energy storage devices. A comprehensive review of polymeric electrochemistry is provided, focusing on how polymers maintain electrical insulation and enable ion transport, two essential functions for devices such as supercapacitors and batteries. Advanced fabrication techniques, including solution casting, melt processing, electrospinning, and in-situ polymerization are emphasized for tailoring polymer electrolytes to achieve optimal microstructural and electrochemical properties. The study further explores the electrochemical characteristics of polymer electrolytes, focusing on the electrochemical impedance spectroscopy technique. By offering a thorough understanding of both the theoretical and practical aspects of polymer electrolytes, this study contributes to the development of more effective and long-lasting energy storage systems. This discussion aligns with the global trend toward innovative and eco-friendly energy technologies while advancing the field of materials research.


  • Effects of lithium perchlorate on the electrochemical performance of PVDF-HFP/CA composite-based solid-state electrolytes

    by Izuan Nasib, Muhammad Remanul Islam, Maryam Firouzi, Ahmad Naim Ahmad Yahaya, Sairul Izwan Bin Safie, Sam Toan

    Composite-based polymer electrolytes have attracted considerable attention due to their high ionic conductivity and excellent electrochemical performance in energy storage applications. This study explores the influence of Lithium Perchlorate (LiClO 4 ) loading on the electrochemical performance of composite-based solid-state electrolytes (SSEs) based on a composite of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and 20% cellulose acetate (CA), referred to as PVDF-HFP/20%CA. Utilizing a solution casting method, four SSE samples were fabricated: a control (0% LiClO 4 ) and three samples with varying LiClO 4 concentrations (5%, 10%, and 15%). Comprehensive characterizations, including scanning electron microscopy (SEM), Fourier-transform infrared (FTIR), physical characterization, and electrochemical impedance spectroscopy (EIS) were conducted to assess the impact of LiClO 4 on the composites. The Nyquist plot and DC ionic conductivity analysis further validate the superior performance of PH20CA-15Li (PVDF-HFP/20% cellulose acetate with 15% LiClO 4 ), with ionic conductivity increasing from 1.15 × 10 −6 S cm −1 for the control sample to 3.7 × 10 −6 S cm −1 . Loss Tangent and Cyclic Voltammetry analyses underscore the dynamic electrochemical behavior and stability of PH20CA-15Li, with the voltage window expanding from 0.996 V in the control sample to 1.398 V, highlighting its enhanced dielectric properties and energy storage capabilities. Electrolyte uptake and porosity analyses reveal a decrease in both parameters with increased LiClO 4 content, suggesting a trade-off between electrochemical performance and physical properties. SEM and FTIR analyses show structural and chemical changes, confirming the interaction between LiClO 4 and the composite matrix. The study concludes that 15% LiClO 4 loading optimally balances conductivity with physical properties, making it a promising candidate for advanced solid-state electrolyte applications.

  • Influence of graphene nanoplatelet on carboxymethyl cellulose for enhanced electrochemical performance

    by Muhammad Remanul Islam, Izuan Nasib, Syed Nafiz, Mohammad Dalour Beg, Kim Pickering, Mohd Al-Fatihhi, Ahmad Naim Ahmad Yahaya, Sairul Izwan Bin Safie, Gulam Smdani

    Renewable and bio-based polymers are favored over conventional synthetic polymers because of their low-cost, abundance and sustainability, but due to their average electrochemical performance, sometimes their application is limited as battery material. This study investigates the electrochemical properties of nanocomposites composed of carboxymethyl cellulose (CMC) and graphene nanoplatelets (GNP) at varying GNP ratios. Four samples with GNP weight ratios ranging from 0 to 0.33 wt.% were subjected to analysis using electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy. The sample containing 0.33% GNP exhibited the most favorable electrochemical behavior, demonstrating an ionic conductivity of approximately 2.54 × 10−5 S/cm at 25 °C. Cyclic Voltammogram and Nyquist plots indicated an electrochemical process governed by diffusion processes, particularly evident with 0.33% GNP. This sample displayed the highest specific capacitance at 4.290 F/g, representing an 83.07% improvement over the Pure CMC sample, along with a favorable electrochemical window at 375 mV. Bode plot analysis underscored the influence of diffusion and charge transfer on resistance and conductivity, highlighting enhanced ion mobility in this sample. SEM micrographs revealed improved GNP dispersion in the CMC matrix at higher GNP concentrations, enhancing contact. FTIR analysis confirmed effective CMC–GNP interaction, characterized by a specific peak at 1589 cm−1. These findings provide valuable insights into the electrochemical potential of CMC–GNP composites, offering prospects for their application in diverse electrochemical devices.


  • A Short Communication on the Application of MATLAB in Material Science

    by Gulam Smdani, Muhammad Remanul Islam, Mohd Ismail Yusuf, Sairul Izwan Safie, Ahmad Naim Ahamad Yahaya, Amin Firouzi

  • Integrating a Hydrogen Fuel Cell in a Vehicle as a Hybrid for a Sustainable Energy Application

    by Muhammad Amer Zahin Ahmad Dzaki, Ernie Mazuin Mohd Yusof, Siti Nor Zawani Ahmmad, Norziana Yahya, Muhammad Remanul Islam


  • Mechanical and Thermal Properties of Polylactic Acid Composites Filled with Iron Particles

    by Muhammad Remanul Islam, Mohd Al-Fatihhi Mohd Szali Januddi, Mohd Haziq Zakaria, Sairul Izwan Safie, Ahmad Naim Ahamd Yahaya, Golam Sumdani, Amin Firouzi

  • Mechanical and Thermal Properties of Polylactic Acid/Carbon Fiber Composites

    by Muhammad Remanul Islam, Mohd Al-Fatihhi Mohd Szali Januddi, Mohd Haziq Zakaria, Ahmad Naim Ahmad Yahaya, Sairul Izwan Shafie, Amin Firouzi

  • Open Access

    Review of: "Investigation of the properties of the composition obtained based on mixtures of polyvinyl chloride"

    by Muhammad Remanul Islam

    The title is not clear What properties and what are the compounds are in the mixture should reflect in the title. The abstract should be shorten and re-written focusing on the chronological manner: The aim and objective, materials and methods used...

  • Facile preparation of polyaniline/graphene oxide composite towards electrode materials

    by Muazzin Mupit, Mohd Asyadi Azam, Muhammad Remanul Islam, Rosli Yunus, Ong Siew Kooi, Mohd Al Fatihhi Mohd Szali Januddi

    Polyaniline (PANi) reinforced with graphene oxide (GO) composites were synthesized via in-situ polymerization. The GO was synthesized from natural graphite flakes via the modified Hummer's method. The PANi/GO composites were characterized by Raman spectroscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis. The composites were used as supercapacitor electrodes and the performances were measured by the specific gravimetric capacitance ( Csp) from cyclic voltammetry and charge/discharge characteristics. The maximum value of [ ] was recorded as 36 F/g at a current density of 1 A/g for a loading of 50 wt.% of GO. However, the maximum energy density and power density were recorded as of 2.28 Wh kg−1 and 259.06 W kg−1, respectively, for the loading of 10 wt.% of GO. Additionally, the PANi/GO exhibited the highest capacitance retention of about 76.96% after 5000 cycles at a current density of 1 A/g. The electrochemical performance of the PANi/GO composites was suitable to be used for energy storage devices application.