MSMariusz Stepien

Mariusz Stepien

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mariusz Stepien has a total of 94 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sparse-sensing-based reduced modeling for rapid characterization of nonlinear magnetic inductors

    by Kamil Gruszczyk, Paweł Lasek, Mariusz StęPień, Krzysztof Habelok

    Rapid prototyping of magnetic inductors requires the evaluation of inductance over a wide range of turn counts and operating currents. This task becomes computationally or experimentally demanding when nonlinear magnetic materials are considered because each candidate design may require iterative solution of the magnetic circuit model or repeated evaluations. This paper proposes a sparse-sensing framework for reconstructing inductance curves using a small number of strategically selected turn counts. A reduced basis is constructed by singular value decomposition (SVD), and informative sensing turn counts are selected by QR decomposition with column pivoting. The resulting model reconstructs the full inductance–turn relationship from only a few evaluations. The method is demonstrated using simulated nonlinear toroidal inductor data and then incorporated into a multi-objective design workflow to select candidate cores from a commercial database. The results show that five selected turn counts are sufficient to reconstruct the inductance curve with a relative error below 0.1% in the validation cases under consideration. Combined with the non-dominated sorting genetic algorithm II (NSGA-II) optimization, the reduced model enables rapid screening of feasible core, material, and stacking configurations while preserving accuracy sufficient for engineering design.

  • Open Access

    Nonlinear Optimal and Multi-loop Flatness-based Control for PMSM-driven Robotic Manipulators

    by Gerasimos Rigatos, Masoud Abbaszadeh, Jose Limaverde-Filho, Zhiwei Gao, Pierluigi Siano, Mariusz Stepien

    A nonlinear optimal control method is proposed for robotic manipulators actuated by permanent magnet synchronous motors (PMSMs). A two-link robotic manipulator with PMSM actuators is considered . The robot's nonlinear and multivariable state-space model is formulated and its differential flatness properties are proven. The dynamic model of the PMSM-driven robot is linearized at each sampling instance with the use of first-order Taylor series expansion and though the computation of the associated Jacobian matrices. Within each sampling period, the time-varying linearization point is defined by the present value of the robot's state vector and by the last sampled value of the control inputs vector. To solve the related optimal control problem under model uncertainties and external perturbations an H-infinity controller is designed for the linearized model of the robot. To obtain the stabilizing feedback gains of the H-infinity controller an algebraic Riccati equation is solved at each time-step of the control method. Through Lyapunov stability analysis it is proven that the robot's control scheme satisfies the H-infinity tracking performance conditions, which indicates robustness. Moreover, global asymptotic stability is proven for the control loop. The method achieves fast convergence of the robot's state variables to the associated reference trajectories, and keeps moderate the variations of the control inputs. The nonlinear optimal control method is compared against a multi-loop flatness-based control approach which is also shown to be globally stable and to ensure fine tracking performance for the robot.

  • System elektromagnetycznego sterowania siłą docisku elektrod w zgrzewarkach rezystancyjnych

    by Mariusz StęPień, Krystian Frania, Dominik Mikołajczyk, Jan Zygadlewicz, Mateusz Czechowski, Natan Siekierka, Wiktor Czornik

    Artykuł poświęcony jest opracowaniu i badaniom systemu sterowania siłą docisku elektrod w zgrzewarce rezystancyjnej. Jest to rozwiązanie nowatorskie, mogące zastąpić stosowane dotąd systemy pneumatyczne lub serwomechaniczne. Zaproponowany w artykule system bazuje na systemie czterech elektromagnesów – dwóch przyciągających i dwóch powrotnych, czterokanałowym układzie energoelektronicznym zasilania oraz na wspólnym układzie sterowania, pozwalającym na równoważenie sił między elektromagnesami.

  • Application of a Cylindrical Halbach Array for HTS Tapes Characterization

    by Krzysztof Habelok, Paweł Lasek, Kamil Gruszczyk, Mariusz StęPień

    For precise angular characterization of high temperature superconducting (HTS) tapes, creating a stable and uniform magnetic field that allowsfull 360° sample rotation poses specific design and implementationchallenges. This work introduces a compact cylindrical Halbach array composed of permanent magnets, designetto generate a uniform magnetic flux density up to 350 mT. The system is dedicated to angular dependent measurements of the critical current lc in HTS tapes. The Halbach configuration was optimized using finite element method (FEM) simulations to maximize field uniformity in the measurement region. The experimental setup was fabricated usingadditive manufacturing and integrates the Halbach array with a four probe measurement system operating at 77 K. The mechanical design ensures precise, continuous rotation of the superconducting sample within a cryogenic environment without degrading field symmetry. Angular dependence of lc was experimentally characterized and compared with results obtained using conventional solenoidal magnets and established analytical models. The results confirm that the Halbach array provides sufficient magnetic field uniformityfor reliable lc (θ) determination while significantly reducing system cost, power demand, and cooling complexity. The maximum field of approximately 0.35 T limits the applicability of the device to low- and moderate-field measurements, making it particularly suitable for laboratory scale testing and industrial quality control of HTS conductors

  • Open Access

    Pulsed operation of a DC welding power source in resistance projection welding

    by Zygmunt Mikno, Mariusz Stepien, Wenqi Zhang, Murali Tumuluru

    The effect of pulse welding current (DC, 1 kHz) on the progression of projection welding process of nuts was analysed. The study involved a comparative analysis using identical average value for pulsed DC current with continuous direct current (DCc), which is commonly used in conventional mode. The analysis was conducted for nuts featuring four trapezoidal projections, made of grade 10B21 steel (AISI1017-SORPAS library), with a projection height of 1.2 mm and an initial contact area between the projection and the sheet metal of 7.8 mm 2 . The second welded component was a 3.0 mm thick DC04 sheet metal. Numerical analyses in both cases were conducted using the SORPAS ™ software. The characteristic parameters evaluated were weld strength, volume of melted material (in both the sheet and the projection), area of molten material in the contact region, welding energy, and average welding current. The results of the numerical calculations were verified experimentally. The study demonstrated the beneficial effect of pulsed welding current (DC, 1 kHz) on weld quality, particularly in terms of improved strength. It is possible to both reduce welding time and increase weld strength for pulsed DC welding. With comparable weld strength, welding time can be reduced by over 30%. In turn, for the same welding time (and thus the same energy), the weld strength can be increased by 35%.


  • Open Access

    Comparative analysis of a projection welding process with AC and DC current source for susceptibility study

    by Zygmunt Mikno, Mariusz Stepien, Yu-Jun Xia

    The paper is aimed at the analysis of the influence of the welding current source (type-AC/DC) and its connection to the electrical grid on the quality of the resistance projection welding process (nuts/bolds). The investigation is based on FEM-SORPAS analysis. The relationship between (i) weld strength, (ii) the area of the melted material in the contact area of the welded elements, i.e., projection—sheet metal, and (iii) the volume of the melted material in the welding area is described in relation to the type of the welding current (AC/DC). Selected FEM calculations were referred to experimental results. In the second step, the influence of a source type and connection method on the decrease of the welding current was determined by a circuit modelling using the FALSTAD simulation environment. The obtained results show that the voltage drop and current decrease caused by the line connections and converter structure significantly reduce the strength of the joint. For nominal parameters, i.e., welding current source (type-AC/DC), the FEM calculation results were verified experimentally. Metallographic examinations of welded joints (AC/DC) were performed and compared with the temperature distribution in the welding area for FEM.


  • Open Access

    Analysis of welding conditions at synchronous operation of resistance welding machines

    by Zygmunt Mikno, Mariusz Stepien

    The paper is devoted to analysis of power losses in a resistance welding machine including supplying system and examination of welding conditions of the welding machine current in a case of synchronous (simultaneous) operation of multiple welding machines, i.e., during the conduction of welding current. Analysis of the most important contributors of power losses generated on the current path between a power source and the welded joint is carried out. The analysis is carried out for a DC (direct current) welding machine with power electronics inverter. AC (alternating current) welding machines are also taken into account. The analysis is divided in two parts. The first one is the analysis of single welding machine operation, while in the second part, coexistence (mutual operation) of two synchronous welding machines is considered. The analysis is based on results of numerical and experimental investigations. The first one is focused on calculation of power losses in the energy path (including a Sankey type power loss distribution diagrams), and the second one is based on experimental tests carried out to determine the diameter of the weld nugget and the strength of the joints, for cases of reducing the welding current. An example of simultaneous operation of welding machines was presented and discussed. The percentage voltage drops and power losses in the entire power supply path of the resistance welder are shown. The analysis carried out is extremely important from this point quality of welded joints.


  • Perspektywy rozwoju zastosowań nadprzewodnictwa w elektrotechnice i energetyce - mapa drogowa

    by Mariusz Stępień, Henryka Danuta Stryczewska

    Technologia nadprzewodnikowa bazująca na materiałach charakteryzujących się unikatowymi właściwościami w zakresie przewodzenia prądu elektrycznego oraz oddziaływania w polu magnetycznym ma szanse na szeroki rozwój w zakresie aplikacji elektrotechnicznych i energetycznych. Nadprzewodnictwo, mimo że znane jest od ponad 110 lat, wymaga strategicznego i długofalowego podejścia do wdrażania tej zaawansowanej, ale też wrażliwej na warunki eksploatacyjne, technologii. Artykuł nakreśla mapę drogową rozwoju nadprzewodnictwa w obszarze elektrotechniki, opracowywaną w ramach prac Sekcji Materiałów i Technologii Elektrotechnicznych Komitetu Elektrotechniki Polskiej Akademii Nauk.

  • Projekty PBL jako przykład nowoczesnego kształcenia zindywidualizowanego w obszarze energoelektroniki

    by Mariusz Stępień, Paweł LASEK, Dawid Mańka, Patryk Tylutki

    W artykule przedstawiono metody nowoczesnych form kształcenia zapewniających indywidualne podejście do wymagań studenta na przykładzie kształcenia „Project/Problem Based Learning” realizowanego w Politechnice Śląskiej w ramach Inicjatywy Doskonałości Uczelnia Badawcza. W artykule opisano trzy przykładowe projekty zrealizowane w ostatnim czasie, związane z zagadnieniami energoelektroniki, napędu elektrycznego i robotyki.

  • Experimental analysis of the air- and water-based cooling solution for the three-phase line choke

    by Michal Palacz, Jakub Bodys, Pawel Lasek, Bartlomiej Melka, Michal Stebel, Mariusz Stepien, Artur Strug, Miroslaw Lukiewski, Michal Halski, Edyta Piechnik, et al.