Swapan Kumar Karak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Swapan Kumar Karak has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Anshuman Patra
Department of Metallurgical and Materials Engineering, National Institute of Technology Rourkela, Rourkela, India
7 shared publications - Mithilesh Kumar
National Institute of Technology Rourkela
6 shared publications - Santosh Kumar Sahoo
Department of Metallurgical & Materials Engineering, NIT Rourkela, Rourkela, India
6 shared publications - Anand Babu Kotta
National Institute of Technology
2 shared publications - Debasis Chaira
Department of Metallurgical and Materials Engineering, National Institute of Technology, Rourkela, India
2 shared publications - Łukasz Ciupiński
Faculty of Materials Science and Engineering, Warsaw University of Technology, 141 Woloska St., 02-507 Warsaw, Poland
2 shared publications
Latest Publications
- 15 November 2023
- Published by Springer Nature
- p. 167-199
Thermodynamics of Solutions
- 15 November 2023
- Published by Springer Nature
- p. 81-123
Free Energy, Criteria for Equilibrium and Thermodynamic Relations
- 15 November 2023
- Published by Springer Nature
- p. 81-123
Free Energy, Criteria for Equilibrium and Thermodynamic Relations
- 15 November 2023
- Published by Springer Nature
- p. 15-46
First Law of Thermodynamics
- 15 November 2023
- Published by Springer Nature
- p. 1-14
Introduction
- 15 November 2023
- Published by Springer Nature
- p. 47-80
Second Law of Thermodynamics and Entropy
- 15 November 2023
- Published by Springer Nature
- p. 125-165
Fugacity, Activity, Equilibrium Constant and Ellingham Diagram
- 15 November 2023
- Published by Springer Nature
- p. 125-165
Fugacity, Activity, Equilibrium Constant and Ellingham Diagram
- 9 March 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (11) , 4601-4617
Effects of Si and Oxide Additives on Phase Evolution, Microstructure and Mechanical Properties of Si3N4–Mo Cermet Fabricated by Conventional Powder Metallurgy
- 9 March 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (11) , 4601-4617
Effects of Si and Oxide Additives on Phase Evolution, Microstructure and Mechanical Properties of Si3N4–Mo Cermet Fabricated by Conventional Powder Metallurgy
- 19 February 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 978, 525-531
Effect of Mineralogy on Reduction Behaviour of Iron Ore Pellets
The present study deals with impact of gangue amount (Al2O3, SiO2) in iron ores on reduction of its pellets for production of sponge iron. Iron ore pellets were reduced isothermally with noncoking coal fines in the range of 1123 - 1273 K with a time interval of 15, 30,45,60,90 and 120 min. As the temperature rose from 1123 to 1223 K, the reducibility index of iron ore pellets increased and then decreased at temperature 1273 K. All iron ore pellets shows complete reduction at temperatures of 1173 and 1223 K within 120 minutes. The reduction results clearly show that the reducibility of the pellets depends on the initial mineralogy of the ore. It was also observed that the reducibility decreased as gangue content (Al2O3 + SiO2) increases. The activation energy of the pellets decreased from 46.54 and 49.13 kJ/mol when the gangue content increased. The pellets were metallographically characterized before and after reduction to identify phase transformations. Examination of the SEM microphotographs revealed that Whisker shape of iron grains were formed during the reduction process and clear porous structure was observed.
- 19 February 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 978, 525-531
Effect of Mineralogy on Reduction Behaviour of Iron Ore Pellets
The present study deals with impact of gangue amount (Al2O3, SiO2) in iron ores on reduction of its pellets for production of sponge iron. Iron ore pellets were reduced isothermally with noncoking coal fines in the range of 1123 - 1273 K with a time interval of 15, 30,45,60,90 and 120 min. As the temperature rose from 1123 to 1223 K, the reducibility index of iron ore pellets increased and then decreased at temperature 1273 K. All iron ore pellets shows complete reduction at temperatures of 1173 and 1223 K within 120 minutes. The reduction results clearly show that the reducibility of the pellets depends on the initial mineralogy of the ore. It was also observed that the reducibility decreased as gangue content (Al2O3 + SiO2) increases. The activation energy of the pellets decreased from 46.54 and 49.13 kJ/mol when the gangue content increased. The pellets were metallographically characterized before and after reduction to identify phase transformations. Examination of the SEM microphotographs revealed that Whisker shape of iron grains were formed during the reduction process and clear porous structure was observed.
- 1 April 2019
- Published by Ram Arti Publishers in International Journal of Mathematical, Engineering and Management Sciences
- Vol. 4 (2) , 521-530
Variation of Microstructural and Mechanical Properties With Respect to Polarity in Shielded Metal Arc Welding of Mild Steel
Welding has been done by taking mild steel as work piece material in shielded metal arc welding (SMAW) process. Material thickness and current were considered as input parameters. Joining of metals has been completed in two ways. In first process double pass welding has been done in which 1st pass was in reverse polarity and the second pass was in straight polarity and in the 2nd process both the passes of welding were completed with straight polarity. The comparison of microstructure and impact toughness has been investigated. It was found that more amount of heat was generated in the 2nd process as compared to the 1st process. Therefore, growths of grains in heat affected zone occurred and maximum growth occurred in 2nd than 1st process. Impact strength increased with decrease in current value and increase in material thickness respectively. The impact strength values for 1st process welding were relatively less as compared to 2nd process.
- 1 April 2019
- Published by Ram Arti Publishers in International Journal of Mathematical, Engineering and Management Sciences
- Vol. 4 (2) , 521-530
Variation of Microstructural and Mechanical Properties With Respect to Polarity in Shielded Metal Arc Welding of Mild Steel
Welding has been done by taking mild steel as work piece material in shielded metal arc welding (SMAW) process. Material thickness and current were considered as input parameters. Joining of metals has been completed in two ways. In first process double pass welding has been done in which 1st pass was in reverse polarity and the second pass was in straight polarity and in the 2nd process both the passes of welding were completed with straight polarity. The comparison of microstructure and impact toughness has been investigated. It was found that more amount of heat was generated in the 2nd process as compared to the 1st process. Therefore, growths of grains in heat affected zone occurred and maximum growth occurred in 2nd than 1st process. Impact strength increased with decrease in current value and increase in material thickness respectively. The impact strength values for 1st process welding were relatively less as compared to 2nd process.