Paulo Abreu
Research Subjects
Paulo Abreu has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
- Ricardo A. Fonseca
Universidade de Lisboa
2 shared publications A. Puig Sitjes
Max Planck Institut fuer Plasmaphysik, Garching, Germany
1 shared publication- A. Salmi
VTT, PO Box 1000, FI-02044 VTT Espoo, Finland
1 shared publication A. Sirinelli
ITER Organization 8 , Route de Vinon, CS 90 046, 13067 Saint-Paul-Lez-Durance, France
1 shared publication- Andrea Murari
Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova, Italy
1 shared publication - Antonio Silva
Universidade de Lisboa Instituto Superior Tecnico
1 shared publication
Latest Publications
- Open Access
- 27 November 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (1) , 017002
Summary of the 5th IAEA technical meeting on fusion data processing, validation and analysis (FDPVA)
The purpose of the 5th International Atomic Energy Agency technical meeting on fusion data processing, validation and analysis (FDPVA) (Ghent University, Ghent, Belgium, 12–15 June 2023) was to provide a platform during which a set of topics relevant to FDPVA were discussed with the view of meeting the needs of next step fusion devices such as ITER. The validation and analysis of experimental data obtained from diagnostics used to characterize fusion plasmas are crucial for a knowledge-based understanding of the physical processes governing the dynamics of these plasmas. This paper presents the recent progress and achievements in the domain of plasma diagnostics data analysis and synthetic diagnostics reported at the meeting, including concept description of new devices; fusion databases; integrated data analysis; inverse problems; uncertainty propagation, verification and validation; probabilistic methods and machine learning. The relevant results underline trends observed in the current major fusion confinement devices.
- 27 November 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (1) , 017002
Open AccessSummary of the 5th IAEA technical meeting on fusion data processing, validation and analysis (FDPVA)
The purpose of the 5th International Atomic Energy Agency technical meeting on fusion data processing, validation and analysis (FDPVA) (Ghent University, Ghent, Belgium, 12–15 June 2023) was to provide a platform during which a set of topics relevant to FDPVA were discussed with the view of meeting the needs of next step fusion devices such as ITER. The validation and analysis of experimental data obtained from diagnostics used to characterize fusion plasmas are crucial for a knowledge-based understanding of the physical processes governing the dynamics of these plasmas. This paper presents the recent progress and achievements in the domain of plasma diagnostics data analysis and synthetic diagnostics reported at the meeting, including concept description of new devices; fusion databases; integrated data analysis; inverse problems; uncertainty propagation, verification and validation; probabilistic methods and machine learning. The relevant results underline trends observed in the current major fusion confinement devices.
- Open Access
- 1 April 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (4)
Improved accuracy and robustness of electron density profiles from JET’s X-mode frequency-modulated continuous-wave reflectometers
JET’s frequency-modulated continuous wave (FMCW) reflectometers have been operating well with the current design since 2005, and density profiles have been automatically calculated intershot since then. However, the calculated profiles had long suffered from several shortcomings: poor agreement with other diagnostics, sometimes inappropriately moving radially by several centimeters, elevated levels of radial jitter, and persistent wriggles (strong unphysical oscillations). In this research, several techniques are applied to the reflectometry data analysis, and the shortcomings are significantly improved. Starting with improving the equilibrium reconstruction that estimates the background magnetic field, adding a ripple correction in the reconstructed magnetic field profile, and adding new inner-wall reflection positions estimated through ray-tracing, these changes not only improve the agreement of reconstructed profiles to other diagnostics but also solve density profile wriggles that were present during band transitions. Other smaller but also persistent wriggles were also suppressed by applying a localized correction to the measured beat frequency where persistent oscillations are present. Finally, the burst analysis method, as introduced by Varela et al. [Nucl. Fusion 46 S693 (2006)], has been implemented to extract the beat frequency from stacked spectrograms. Due to the strong suppression of spurious reflections, the radial jitter that sometimes would span several centimeters has been strongly reduced. The stacking of spectrograms has also been shown to be very useful for stacking recurring events, like small gas puff modulations, and extracting transport coefficients that would otherwise be below the noise level.
- 1 April 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (4)
Open AccessImproved accuracy and robustness of electron density profiles from JET’s X-mode frequency-modulated continuous-wave reflectometers
JET’s frequency-modulated continuous wave (FMCW) reflectometers have been operating well with the current design since 2005, and density profiles have been automatically calculated intershot since then. However, the calculated profiles had long suffered from several shortcomings: poor agreement with other diagnostics, sometimes inappropriately moving radially by several centimeters, elevated levels of radial jitter, and persistent wriggles (strong unphysical oscillations). In this research, several techniques are applied to the reflectometry data analysis, and the shortcomings are significantly improved. Starting with improving the equilibrium reconstruction that estimates the background magnetic field, adding a ripple correction in the reconstructed magnetic field profile, and adding new inner-wall reflection positions estimated through ray-tracing, these changes not only improve the agreement of reconstructed profiles to other diagnostics but also solve density profile wriggles that were present during band transitions. Other smaller but also persistent wriggles were also suppressed by applying a localized correction to the measured beat frequency where persistent oscillations are present. Finally, the burst analysis method, as introduced by Varela et al. [Nucl. Fusion 46 S693 (2006)], has been implemented to extract the beat frequency from stacked spectrograms. Due to the strong suppression of spurious reflections, the radial jitter that sometimes would span several centimeters has been strongly reduced. The stacking of spectrograms has also been shown to be very useful for stacking recurring events, like small gas puff modulations, and extracting transport coefficients that would otherwise be below the noise level.
- 1 September 2016
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 87 (9) , 093506
Electron cyclotron emission spectra in X- and O-mode polarisation at JET: Martin-Puplett interferometer, absolute calibration, revised uncertainties, inboard/outboard temperature profile, and wall properties
At the tokamak Joint European Torus (JET), the electron cyclotron emission spectra in O-mode and X-mode polarisations are diagnosed simultaneous in absolute terms for several harmonics with two Martin-Puplett interferometers. From the second harmonic range in X-mode polarisation, the electron temperature profile can be deduced for the outboard side (low magnetic field strength) of JET but only for some parts of the inboard side (high magnetic field strength). This spatial restriction can be bypassed, if a cutoff is not present inside the plasma for O-mode waves in the first harmonic range. Then, from this spectral domain, the profile on the entire inboard side is accessible. The profile determination relies on the new absolute and independent calibration for both interferometers. During the calibration procedure, the antenna pattern was investigated as well, and, potentially, an increase in the diagnostic responsivity of about 5% was found for the domain 100–300 GHz. This increase and other uncertainty sources are taken into account in the thorough revision of the uncertainty for the diagnostic absolute calibration. The uncertainty deduced and the convolution inherent for Fourier spectroscopy diagnostics have implications for the temperature profile inferred. Having probed the electron cyclotron emission spectra in orthogonal polarisation directions for the first harmonic range, a condition is derived for the reflection and polarisation-scrambling coefficients of the first wall on the outboard side of JET.
- 1 September 2016
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 87 (9) , 093506
Electron cyclotron emission spectra in X- and O-mode polarisation at JET: Martin-Puplett interferometer, absolute calibration, revised uncertainties, inboard/outboard temperature profile, and wall properties
At the tokamak Joint European Torus (JET), the electron cyclotron emission spectra in O-mode and X-mode polarisations are diagnosed simultaneous in absolute terms for several harmonics with two Martin-Puplett interferometers. From the second harmonic range in X-mode polarisation, the electron temperature profile can be deduced for the outboard side (low magnetic field strength) of JET but only for some parts of the inboard side (high magnetic field strength). This spatial restriction can be bypassed, if a cutoff is not present inside the plasma for O-mode waves in the first harmonic range. Then, from this spectral domain, the profile on the entire inboard side is accessible. The profile determination relies on the new absolute and independent calibration for both interferometers. During the calibration procedure, the antenna pattern was investigated as well, and, potentially, an increase in the diagnostic responsivity of about 5% was found for the domain 100–300 GHz. This increase and other uncertainty sources are taken into account in the thorough revision of the uncertainty for the diagnostic absolute calibration. The uncertainty deduced and the convolution inherent for Fourier spectroscopy diagnostics have implications for the temperature profile inferred. Having probed the electron cyclotron emission spectra in orthogonal polarisation directions for the first harmonic range, a condition is derived for the reflection and polarisation-scrambling coefficients of the first wall on the outboard side of JET.
- 3 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 39 (2) , 675-685
PIC Codes in New Processors: A Full Relativistic PIC Code in CUDA-Enabled Hardware With Direct Visualization
Kinetic plasma simulations using an electromagnetic particle-in-cell (PIC) algorithm have become the tool of choice for numerical modeling of several astrophysical and laboratory scenarios, ranging from astrophysical shocks and plasma shell collisions, to high-intensity laser-plasma interactions, with applications to fast ignition and particle acceleration. However, fully relativistic kinetic codes are computationally intensive, and new computing paradigms are required for one-to-one direct modeling of these scenarios. In this paper, we look at the use of modern graphics processing units for PIC algorithm calculations, discussing the implementation of a fully relativistic PIC code using NVIDIA's Compute Unified Device Architecture, also allowing one for simultaneous visualization of simulation results with negligible impact on performance. Details on the algorithm implementation are given, focusing on grid-particle interpolation and current deposition and also on the direct visualization routines. Finally, we present results from a test simulation of an electron/positron plasma shell collision, focusing on code validation and performance evaluation.
- 3 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 39 (2) , 675-685
PIC Codes in New Processors: A Full Relativistic PIC Code in CUDA-Enabled Hardware With Direct Visualization
Kinetic plasma simulations using an electromagnetic particle-in-cell (PIC) algorithm have become the tool of choice for numerical modeling of several astrophysical and laboratory scenarios, ranging from astrophysical shocks and plasma shell collisions, to high-intensity laser-plasma interactions, with applications to fast ignition and particle acceleration. However, fully relativistic kinetic codes are computationally intensive, and new computing paradigms are required for one-to-one direct modeling of these scenarios. In this paper, we look at the use of modern graphics processing units for PIC algorithm calculations, discussing the implementation of a fully relativistic PIC code using NVIDIA's Compute Unified Device Architecture, also allowing one for simultaneous visualization of simulation results with negligible impact on performance. Details on the algorithm implementation are given, focusing on grid-particle interpolation and current deposition and also on the direct visualization routines. Finally, we present results from a test simulation of an electron/positron plasma shell collision, focusing on code validation and performance evaluation.
- 1 January 2009
- Published by AIP Publishing
- p. 328-333
Streaming the Boris Pusher: a CUDA implementation
We demonstrate an implementation of the Boris Particle Pusher Algorithm using CUDA‐enabled processors. A simplified PIC code is used as a reference for the pusher and several tests are shown. The deployment time from a developer point of view is also evaluated. Results show that CUDA is a good tool for significant code acceleration with minimal code impact and minimal effort for the developer.
- 1 January 2009
- Published by AIP Publishing
- p. 328-333
Streaming the Boris Pusher: a CUDA implementation
We demonstrate an implementation of the Boris Particle Pusher Algorithm using CUDA‐enabled processors. A simplified PIC code is used as a reference for the pusher and several tests are shown. The deployment time from a developer point of view is also evaluated. Results show that CUDA is a good tool for significant code acceleration with minimal code impact and minimal effort for the developer.