Pilar Castejón
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pilar Castejón has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- David Arencón
Universitat Politecnica de Catalunya
3 shared publications - Antonio B. Martínez
Centre Català del Plàstic, Universitat Politècnica de Catalunya., C/Colom 114, 08222 Terrassa, Spain
2 shared publications - Marcelo Antunes
Poly2 Group, Department of Materials Science and Engineering, ESEIAAT, Technical University of Catalonia (UPC BarcelonaTech), C/Colom 11, 08222 Terrassa, Spain
2 shared publications A.B. Martínez
1 shared publication- Abdellah Ajji
Polytechnique Montreal
1 shared publication - Amir Saffar
Research Center for High Performance Polymers and Composite Systems, Chemical Engineering Department, Polytecnique Montréal, P.O. Box 6079, Montréal, QC H3C 3A7, Canada
1 shared publication
Latest Publications
- Open Access
Development of Inorganic Particle-Filled Polypropylene/High Density Polyethylene Membranes via Multilayer Co-Extrusion and Stretching
This work is made to ascertain the effects of mineral fillers, namely calcium carbonate and talc, on the morphology and properties of multilayer polypropylene (PP)/high-density polyethylene (HDPE) porous membranes. Multilayer membranes were prepared using the three-stage Melt-Extrusion, Annealing and Uniaxial Stretching (MEAUS) process. The orientation of PP’s crystalline phase was affected by both the flow-induced crystallization and the heterogeneous nucleation promoted by the fillers. A synergistic effect was observed in the filled samples due to the generation of pores after the stretching-induced lamellae separation and the debonding of mineral fillers from the polymeric matrix. The fillers increased the porous surface, leading to an increase of permeance to air, being this effect more marked at higher filler contents. Talc showed a higher efficiency to create porous surfaces when compared to calcium carbonate. The thermal stability of the membranes increased with filler addition, as well as their stiffness and strength.
Open AccessDevelopment of Inorganic Particle-Filled Polypropylene/High Density Polyethylene Membranes via Multilayer Co-Extrusion and Stretching
This work is made to ascertain the effects of mineral fillers, namely calcium carbonate and talc, on the morphology and properties of multilayer polypropylene (PP)/high-density polyethylene (HDPE) porous membranes. Multilayer membranes were prepared using the three-stage Melt-Extrusion, Annealing and Uniaxial Stretching (MEAUS) process. The orientation of PP’s crystalline phase was affected by both the flow-induced crystallization and the heterogeneous nucleation promoted by the fillers. A synergistic effect was observed in the filled samples due to the generation of pores after the stretching-induced lamellae separation and the debonding of mineral fillers from the polymeric matrix. The fillers increased the porous surface, leading to an increase of permeance to air, being this effect more marked at higher filler contents. Talc showed a higher efficiency to create porous surfaces when compared to calcium carbonate. The thermal stability of the membranes increased with filler addition, as well as their stiffness and strength.
- Open Access
Porous Membranes Based on Polypropylene-Ethylene Copolymers. Influence of Temperature on Extrusion, Annealing and Uniaxial Strain Stages
In this study, block and random copolymers of polypropylene–ethylene are selected to prepare porous membranes through the melt extrusion-annealing-uniaxial stretching technique (MEAUS), at a constant draw ratio. In some cases, these copolymers were blended with a homopolymer grade. The variation of temperature in the stages of extrusion, annealing and uniaxial strain was analysed. Several characterisation techniques were employed to study this influence. The crystalline orientation was analysed by polarised infrared spectroscopy (FT-IR), and crystalline features were studied by differential scanning calorimetry (DSC). The thermal stability of the membranes was checked by thermogravimetric analysis (TGA). Tensile tests were performed to ascertain the stiffness and ductility of the produced samples. The results were correlated with the porous morphology, global porosity, and permeability to air. A close relationship was found between crystalline characteristics, porous morphology and the trends registered. An improved pore distribution along the membrane surface was found when copolymers were employed.
Open AccessPorous Membranes Based on Polypropylene-Ethylene Copolymers. Influence of Temperature on Extrusion, Annealing and Uniaxial Strain Stages
In this study, block and random copolymers of polypropylene–ethylene are selected to prepare porous membranes through the melt extrusion-annealing-uniaxial stretching technique (MEAUS), at a constant draw ratio. In some cases, these copolymers were blended with a homopolymer grade. The variation of temperature in the stages of extrusion, annealing and uniaxial strain was analysed. Several characterisation techniques were employed to study this influence. The crystalline orientation was analysed by polarised infrared spectroscopy (FT-IR), and crystalline features were studied by differential scanning calorimetry (DSC). The thermal stability of the membranes was checked by thermogravimetric analysis (TGA). Tensile tests were performed to ascertain the stiffness and ductility of the produced samples. The results were correlated with the porous morphology, global porosity, and permeability to air. A close relationship was found between crystalline characteristics, porous morphology and the trends registered. An improved pore distribution along the membrane surface was found when copolymers were employed.
- Open Access
Polypropylene-Based Porous Membranes: Influence of Polymer Composition, Extrusion Draw Ratio and Uniaxial Strain
Several commercial grades of homo-polymer and its blends were selected to prepare microporous membranes through melt extrusion-annealing-uniaxial stretching technique (MEAUS). Branched or very fluid polypropylene was employed to modify the polymeric composition. In some blends, micro-sized calcium carbonate was added. We analysed the influence of sample composition, extrusion draw ratio, and we performed a deep study concerning the uniaxial strain rate, using in some cases extreme strain rates and strain extents. The crystalline features were studied by Differential Scanning Calorimetry (DSC), and the morphology of porous structure was analyzed through Scanning Electron Microscopy (SEM). Thermal stability and thermomechanical performance was measured by thermogravimetric analysis (TGA) and dynamic-mechanical-thermal (DTMA) study. A close relationship was found between crystalline characteristics, porous morphology and the trends registered for permeability.
Open AccessPolypropylene-Based Porous Membranes: Influence of Polymer Composition, Extrusion Draw Ratio and Uniaxial Strain
Several commercial grades of homo-polymer and its blends were selected to prepare microporous membranes through melt extrusion-annealing-uniaxial stretching technique (MEAUS). Branched or very fluid polypropylene was employed to modify the polymeric composition. In some blends, micro-sized calcium carbonate was added. We analysed the influence of sample composition, extrusion draw ratio, and we performed a deep study concerning the uniaxial strain rate, using in some cases extreme strain rates and strain extents. The crystalline features were studied by Differential Scanning Calorimetry (DSC), and the morphology of porous structure was analyzed through Scanning Electron Microscopy (SEM). Thermal stability and thermomechanical performance was measured by thermogravimetric analysis (TGA) and dynamic-mechanical-thermal (DTMA) study. A close relationship was found between crystalline characteristics, porous morphology and the trends registered for permeability.
- Open Access
- 1 October 2017
- Published by Elsevier in Polymer Testing
- Vol. 63, 180-193
The fracture testing of ductile polymer films: Effect of the specimen notching
- 1 October 2017
- Published by Elsevier in Polymer Testing
- Vol. 63, 180-193
Open AccessThe fracture testing of ductile polymer films: Effect of the specimen notching