LHLiqiang Huang

Liqiang Huang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Liqiang Huang has a total of 116 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Promoting Fast Na Ion Transport at Low Temperatures for Sodium Metal Batteries

    by Zhongqiang Wang, Xueying Zheng, Xuyang Liu, Yangyang Huang, Liqiang Huang, Yuwei Chen, Mei Han, Wei Luo

    Cost concerns have promoted the rise of Na-based batteries as an alternative to Li-based batteries, and the energy density pursuits have brought attention to Na metal anodes. Numerous studies have been conducted on the failure mechanisms and improvement methods of Na metal batteries (NMBs) at room temperature; however, the low-temperature applications are still faced with more complex challenges. On the basis of the concentration effect of the electrolytes, we propose a dilute electrolyte for the low-temperature operation of NMBs. With the low salt concentration and tetrahydrofuran cosolvent, the affinity between Na ions and the solvent molecules is weakened to achieve fast reaction kinetics at low temperatures. The designed electrolyte enables an effectively decreased cell impedance, which improves the cycling stability of Na symmetric cells. As a result, the full cell paired with the Na3V2(PO4)3 cathode maintains a capacity of 80 mAh/g over 250 cycles at -20 °C. This work provides an electrolyte design strategy toward low-temperature NMBs.


  • Toward High Temperature Sodium Metal Batteries via Regulating the Electrolyte/Electrode Interfacial Chemistries

    by Xueying Zheng, Zhang Cao, Zhenyi Gu, Liqiang Huang, Zhonghui Sun, Tong Zhao, Sijie Yu, Xing-Long Wu, Wei Luo, Yunhui Huang


  • Open Access

    Deciphering the Role of Fluoroethylene Carbonate towards Highly Reversible Sodium Metal Anodes

    by Xueying Zheng, Suting Weng, Wei Luo, Bo Chen, Xiao Zhang, Zhenyi Gu, Haotian Wang, Xiaolu Ye, Xuyang Liu, Liqiang Huang, et al.

    Sodium metal anodes (SMAs) suffer from extremely low reversibility (95% with conventional NaPF 6 salt at a regular concentration (1.0 M). The peculiar role of FEC is firstly unraveled via its involvement into the solvation structure, where a threshold FEC concentration with a coordination number>1.2 is needed in guaranteeing high Na reversibility over the long-term. Specifically, by incorporating an average number of 1.2 FEC molecules into the primary Na + solvation sheath, lowest unoccupied molecular orbital (LUMO) levels of such Na + -FEC solvates undergo further decrease, with spin electrons residing either on the O=CO(O) moiety of FEC or sharing between Na + and its C=O bond, which ensures a prior FEC decomposition in passivating the Na surface against other carbonate molecules. Further, by adopting cryogenic transmission electron microscopy (cryo-TEM), we found that the Na filaments grow into substantially larger diameter from ~400 nm to >1 μ m with addition of FEC upon the threshold value. A highly crystalline and much thinner (~40 nm) solid-electrolyte interphase (SEI) is consequently observed to uniformly wrap the Na surface, in contrast to the severely corroded Na as retrieved from the blank electrolyte. The potence of FEC is further demonstrated in a series of “corrosive solvents” such as ethyl acetate (EA), trimethyl phosphate (TMP), and acetonitrile (AN), enabling highly reversible SMAs in the otherwise unusable solvent systems.


  • TiO2 Nanofiber-Modified Lithium Metal Composite Anode for Solid-State Lithium Batteries

    by Yuwei Chen, Ying Huang, Haoyu Fu, Yongmin Wu, Dongdong Zhang, Jiayun Wen, Liqiang Huang, Yiming Dai, Yunhui Huang, Wei Luo

    Solid-state lithium metal batteries (SSLMBs), using lithium metal as the anode and garnet-structured Li6.5La3Zr1.5Ta0.5O12 (LLZTO) as the electrolyte, are attractive and promising due to their high energy density and safety. However, the interface contact between the lithium metal and LLZTO is a major obstacle to the performance of SSLMBs. Here, we successfully improve the interface wettability by introducing one-dimensional (1D) TiO2 nanofibers into the lithium metal to obtain a Li-lithiated TiO2 composite anode (Li–TiO2). When 10 wt % TiO2 nanofibers are added, the formed composite anode offers a seamless interface contact with LLZTO and enables an interfacial resistance of 27 Ω cm2, which is much smaller than 374 Ω cm2 of pristine lithium metal. Due to the enhanced interface wettability, the symmetric Li–TiO2|LLZTO|Li–TiO2 cell upgrades the critical current density to 2.2 mA cm–2 and endures stable cycling over 550 h. Furthermore, by coupling the Li–TiO2 composite anode with the LiFePO4 cathode, the full cell shows stable cycling performance. This work proves the role of TiO2 nanofibers in enhancing the interface contact between the garnet electrolyte and the lithium metal anode and improving the performance of SSLMBs and provides an effective approach with 1D additives for solving the interface issues.


  • Tailoring Electrolyte Solvation Chemistry toward an Inorganic-Rich Solid-Electrolyte Interphase at a Li Metal Anode

    by Xueying Zheng, Liqiang Huang, Wei Luo, Haotian Wang, Yiming Dai, Xuyang Liu, Zhongqiang Wang, Honghe Zheng, Yunhui Huang


  • Opportunities for High-Entropy Materials in Rechargeable Batteries

    by Yuwei Chen, Haoyu Fu, Yangyang Huang, Liqiang Huang, Xueying Zheng, Yiming Dai, Yunhui Huang, Wei Luo


  • Polyolefin Elastomer as the Anode Interfacial Layer for Improved Mechanical and Air Stabilities in Nonfullerene Solar Cells

    by Yansong Ge, Lin Hu, Lifu Zhang, Qingxia Fu, Guodong Xu, Zhi Xing, Liqiang Huang, Weihua Zhou, Yiwang Chen

    Despite the breakthroughs in power conversion efficiency (PCE) values of organic solar cells (OSCs), the other important issue concerning on stability is urgently needed to be resolved for potential commercialization. The commercial and chemically stable polyolefin elastomer (POE) was incorporated into the high-performance PBDB-T:ITIC, PM6:IT-4F and PM6:Y6 non-fullerene systems to serve as anode interfacial layer, affording remarkably improved mechanical and environmental stability as compared with the most studied MoO3 interfacial layer. The POE was found to selectively transport holes rather than electrons, due to the upshifted surface contact potential of active layer and the better ohmic contact between active layer and electrodes. The POE serves as an encapsulating layer to suppress penetration of water and oxygen in addition the diffusion of Ag atoms into active layer. After storing in air environment with the humidity of about 70% for 150 days, the PCE of devices based on PM6:IT-4F with POE anode interfacial layer decreased from 11.88% to 9.60%, remaining 80.8% of the original PCE. In contrast, device using MoO3 as anode interfacial layer showed the PCE value sharply reduced from 12.31% to 2.98% after only storing for 30 days. The POE could be potentially useful for the flexible and large-scale devices fabrication, accelerating the commercialization of OSCs.


  • Highly Adhesive Li-BN Nanosheet Composite Anode with Excellent Interfacial Compatibility for Solid-State Li Metal Batteries

    by Jiayun Wen, Ying Huang, Jian Duan, Yongmin Wu, Wei Luo, Lihui Zhou, Chenchen Hu, Liqiang Huang, Xueying Zheng, Wenjuan Yang, et al.

    Solid-state lithium metal batteries (SSLMBs) are promising energy storage devices by employing lithium metal anodes and solid-state electrolytes (SSEs) to offer high energy density and high safety. However, their efficiency is limited by Li metal/SSE interface barriers, including insufficient contact area and chemical/electrochemical incompatibility. Herein, a strategy to effectively improve the adhesiveness of Li metal to garnet-type SSE is proposed by adding only a few two-dimensional boron nitride nanosheets (BNNS) (5 wt %) into Li metal by triggering the transition from point contact to complete adhesion between Li metal and ceramic SSE. The interface between the Li-BNNS composite anode and the garnet exhibits a low interfacial resistance of 9 Ω cm2, which is significantly lower than that of bare Li/garnet interface (560 Ω cm2). Furthermore, the enhanced contact and the additional BNNS in the interface act synergistically to offer a high critical current density of 1.5 mA/cm2 and a stable electrochemical plating/striping over 380 h. Moreover, the full cell paired with the Li-BNNS composite anode and the LiFePO4 cathode shows stable cycling performance at room temperature. Our results introduce an appealing composite strategy with two-dimensional materials to overcome the interface challenges, which provide more opportunities for the development of SSLMBs.


  • Miscibility Matching and Bimolecular Crystallization Affording High-Performance Ternary Nonfullerene Solar Cells

    by Nan Yi, Qingyun Ai, Weihua Zhou, Liqiang Huang, Lifu Zhang, Zhi Xing, Xiaoyun Li, Jianrong Zeng, Yiwang Chen


  • Unraveling the Morphology in Solution-Processed Pseudo-Bilayer Planar Heterojunction Organic Solar Cells

    by Liqiang Huang, Ping Jiang, Youdi Zhang, Lifu Zhang, Zoukangning Yu, Qiannan He, Weihua Zhou, Licheng Tan, Yiwang Chen

    The conventional bulk heterojunction (BHJ) structure is widely used for fabricating high performance organic solar cells (OSCs) due to the nanometer-scale phase separation of donor/acceptor component. However, the elaborate control of the BHJ morphology is difficult to be carried out because the morphology evolution is such a complicated process. The compatibility requirement of materials in same solvent restricts the structural diversity of molecules to some extent. Meanwhile, the nanoscopic interpenetrating donor/acceptor domains reduce the crystallinity of themselves. The bilayer planar heterojunction, by contrast, possesses of complementary advantages that can be an alternative candidate to achieve the device fabrication and produce different vertical stratification in heterojunction films. But the flat contact area limits the charge separation and transmission efficiency. The sequential solution processed approach was used to facilitate material diffusion in layers. Also, solvent additives were employed to further enhance the diffusion and thus the device performance. Nevertheless, the morphology of the formed pseudo-bilayer planar heterojunction (PPHJ) was not fully revealed yet. Here, we carefully study the morphology of the non-fullerene based PPHJ device in three dimensions. High hole mobility of 2.09 × 10-4 cm2 V-1 s-1 and electron mobility of 7.91 × 10-5 cm2 V-1 s-1 were obtained in the solution-processed PPHJ device. Meanwhile, a distinct phase separation size with vertical rearrangement of donor and acceptor were observed, which enable the pseudo-bilayer devices to equip with a comparable spectral response to BHJ devices. We demonstrate that a freak device architecture (ITO/ZnO/PBDB-T/ITIC/MoO3/Ag) with a PCE of 7% can be obtained from a larger molecular weight of PBDB-T without using extra additives. The solution-processed PPHJ films have much in common with the BHJ films. The results proposed that with appropriate molecular design and vertical phase separation optimization, the performance of solution processed PPHJ based OSCs can be further improved.