Mohammad Nazri Mohd Jaafar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mohammad Nazri Mohd Jaafar has a total of 122 co-authors. Here are the top co-authors by number of shared publications:
- Ashrul Ishak Mohamad Shaiful
Faculty of Mechanical Engineering Technology, Universiti Malaysia Perlis, Malaysia
10 shared publications Hossam S. Aly
6 shared publications- Khalid M. Saqr
Arab Academy for Science Technology and Maritime Transport
6 shared publications Tholudin Mat Lazim
Department of Aeronautical, Automotive & Ocean Engineering
6 shared publicationsYehia A. Eldrainy
Department of Aeronautical Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM, Johor, Malaysia
6 shared publicationsAbdolsaeid Ganjeh Kaviri
4 shared publications
Latest Publications
- 3 May 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2339 (1) , 020235
Utilizing of biodiesel fuel for micro gas turbine combustion performance
Malaysia produces 0.5 tons of palm biodiesel per month, which has great potential to be transformed into valuable fuels for electricity generation by using a micro gas turbine (MGT). The MGT is an alternative power generation unit that is capable to generate the electricity in the range of 10 to above 50 Kilowatt. This unit comprises of automobile turbocharger with a combustion chamber connected in axial between its compressor and turbine. The MGT is able to achieve a maximum approximate temperature value, to 520 517.4°C by using diesel fuel. Next by using B20 Palm Methyl Ester (PME) a maximum approximate temperature is 500499.8°C, B15 Coconut Methyl Ester (CME) at 485.6°C and B30 Jatropha Methyl Ester (JME) at 439.7°C. The reduction percentage of biodiesel temperature at a maximum level compared to diesel was 11.4% for B30 JME, 6.1 % for B15 CME and 3.4 % for B20 PME. Significant aspect here, the knowledge about this reduction rate is established that can be help be help as a new technology in a future.
- 3 May 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2339 (1) , 020235
Utilizing of biodiesel fuel for micro gas turbine combustion performance
Malaysia produces 0.5 tons of palm biodiesel per month, which has great potential to be transformed into valuable fuels for electricity generation by using a micro gas turbine (MGT). The MGT is an alternative power generation unit that is capable to generate the electricity in the range of 10 to above 50 Kilowatt. This unit comprises of automobile turbocharger with a combustion chamber connected in axial between its compressor and turbine. The MGT is able to achieve a maximum approximate temperature value, to 520 517.4°C by using diesel fuel. Next by using B20 Palm Methyl Ester (PME) a maximum approximate temperature is 500499.8°C, B15 Coconut Methyl Ester (CME) at 485.6°C and B30 Jatropha Methyl Ester (JME) at 439.7°C. The reduction percentage of biodiesel temperature at a maximum level compared to diesel was 11.4% for B30 JME, 6.1 % for B15 CME and 3.4 % for B20 PME. Significant aspect here, the knowledge about this reduction rate is established that can be help be help as a new technology in a future.
- Open Access
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 884 (1) , 012026
Combustion and Emission Characteristics of Palm Oil-Based Biodiesel in a Liquid Fuel Burner
This paper presents an experimental investigation of the combustion characteristics of palm oil methyl ester (POME) or called as biodiesel (B), in an open-ended combustion chamber or called as open-ended liquid fuel burner. The performance of conventional diesel fuel (CDF) and various percentages of POME and CDF, which are B10 (10% biodiesel) and B30 (30% biodiesel) were studied to evaluate their performance. Combustion temperature profile in the combustion chamber and exhaust emission concentrations such as NOx, CO and SO2 have been carried out using five different equivalent ratios such as Φ = 0.6, 0.8, 1.0, 1.2 and 1.4. The results show that as the biodiesel content increased, the emission significantly increased except for the NOx emission. It was also found that higher biodiesel content resulting faster combustion rate at near burner region, especially for Φ = 1.0 due to higher Cetane Number (CN) although the lower overall temperature profile produced compared to CDF alone. This proved the suitability of biodiesel for an enhanced transportation engine performance in the near future.
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 884 (1) , 012026
Open AccessCombustion and Emission Characteristics of Palm Oil-Based Biodiesel in a Liquid Fuel Burner
This paper presents an experimental investigation of the combustion characteristics of palm oil methyl ester (POME) or called as biodiesel (B), in an open-ended combustion chamber or called as open-ended liquid fuel burner. The performance of conventional diesel fuel (CDF) and various percentages of POME and CDF, which are B10 (10% biodiesel) and B30 (30% biodiesel) were studied to evaluate their performance. Combustion temperature profile in the combustion chamber and exhaust emission concentrations such as NOx, CO and SO2 have been carried out using five different equivalent ratios such as Φ = 0.6, 0.8, 1.0, 1.2 and 1.4. The results show that as the biodiesel content increased, the emission significantly increased except for the NOx emission. It was also found that higher biodiesel content resulting faster combustion rate at near burner region, especially for Φ = 1.0 due to higher Cetane Number (CN) although the lower overall temperature profile produced compared to CDF alone. This proved the suitability of biodiesel for an enhanced transportation engine performance in the near future.
- 22 May 2020
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 82 (4) , 93-+
COMBUSTION STUDY OF WASTE COOKING OIL BIODIESEL IN AN OIL BURNER
Depletion of fossil fuels, concerns on environment, and fuel price fluctuation have become the major drives in searching for sustainable alternative fuel. In that regard, a study was conducted to evaluate the combustion performance of Waste Cooking Oil (WCO) converted into biodiesel and blended with Conventional Diesel Fuel (CDF) as a mean of sustainable replacement for diesel fuel. In this study, the production of biodiesel fuel from waste cooking oil was done via transesterification process, using the single step approach. The properties of the WCO biodiesel was characterized. The combustion performance of the produced fuels has been studied for B10 and B30 biodiesel from WCO and CDF (as baseline) based on their wall temperature profiles and gaseous emissions generated such as nitrogen oxides (NOx), carbon monoxide (CO) and sulphur dioxide (SO2). It was found that the B30 WCO biodiesel emits lower emission compared to CDF but at the same time generates a lower temperature profile.
- 22 May 2020
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 82 (4) , 93-+
COMBUSTION STUDY OF WASTE COOKING OIL BIODIESEL IN AN OIL BURNER
Depletion of fossil fuels, concerns on environment, and fuel price fluctuation have become the major drives in searching for sustainable alternative fuel. In that regard, a study was conducted to evaluate the combustion performance of Waste Cooking Oil (WCO) converted into biodiesel and blended with Conventional Diesel Fuel (CDF) as a mean of sustainable replacement for diesel fuel. In this study, the production of biodiesel fuel from waste cooking oil was done via transesterification process, using the single step approach. The properties of the WCO biodiesel was characterized. The combustion performance of the produced fuels has been studied for B10 and B30 biodiesel from WCO and CDF (as baseline) based on their wall temperature profiles and gaseous emissions generated such as nitrogen oxides (NOx), carbon monoxide (CO) and sulphur dioxide (SO2). It was found that the B30 WCO biodiesel emits lower emission compared to CDF but at the same time generates a lower temperature profile.
- 22 September 2019
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 81 (6) , 187-193
COMBUSTION PERFORMANCE OF SYNGAS FROM PALM KERNEL SHELL IN A GAS BURNER
Insufficient and various environmental issues of fossil fuels as the current world dominated energy is now becoming a serious global issue. The rapidly increasing demand for alternative energy sources has contributed to the steady growth of renewable energy. Owing to the fact of the abundant presence of palm kernel shell (PKS) as one of palm biomass wastes in South East Asia region, this paper investigates syngas produced from gasified PKS. The investigation is regarding its composition and combustion performance in a gas burner system. It covers emissions analysis, temperature profile and flame length. The produced syngas from downdraft gasifier was burned in the combustion chamber in air-rich and fuel-rich combustion conditions. From the experiment, the results showed that the oxidation zone temperature of above 750°C for the downdraft gasifier is suitable for producing syngas. Produced syngas can be classified as pure-carbon monoxide (CO) syngas due to 94.9% CO content with no hydrogen (H2) content and low heating value (LHV) of 10.7 MJ/kg. The wall temperature profiles for burnt syngas produced via downdraft gasification was higher with longer pattern at fuel-rich condition, which signified higher energy of syngas produced from downdraft gasifier compared to fluidised bed gasifier. The associated flame length was also longer at fuel-rich condition. Produced emission of 56 ppm NOX, 37 ppm CO and 1 ppm SO2 can still be considered as acceptable to human. It can be concluded that syngas produced from PKS shown a high potential to serve as an alternative source of energy due to its high energy content.
- 22 September 2019
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 81 (6) , 187-193
COMBUSTION PERFORMANCE OF SYNGAS FROM PALM KERNEL SHELL IN A GAS BURNER
Insufficient and various environmental issues of fossil fuels as the current world dominated energy is now becoming a serious global issue. The rapidly increasing demand for alternative energy sources has contributed to the steady growth of renewable energy. Owing to the fact of the abundant presence of palm kernel shell (PKS) as one of palm biomass wastes in South East Asia region, this paper investigates syngas produced from gasified PKS. The investigation is regarding its composition and combustion performance in a gas burner system. It covers emissions analysis, temperature profile and flame length. The produced syngas from downdraft gasifier was burned in the combustion chamber in air-rich and fuel-rich combustion conditions. From the experiment, the results showed that the oxidation zone temperature of above 750°C for the downdraft gasifier is suitable for producing syngas. Produced syngas can be classified as pure-carbon monoxide (CO) syngas due to 94.9% CO content with no hydrogen (H2) content and low heating value (LHV) of 10.7 MJ/kg. The wall temperature profiles for burnt syngas produced via downdraft gasification was higher with longer pattern at fuel-rich condition, which signified higher energy of syngas produced from downdraft gasifier compared to fluidised bed gasifier. The associated flame length was also longer at fuel-rich condition. Produced emission of 56 ppm NOX, 37 ppm CO and 1 ppm SO2 can still be considered as acceptable to human. It can be concluded that syngas produced from PKS shown a high potential to serve as an alternative source of energy due to its high energy content.
- Open Access
- 5 November 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 225, 06008
Synthesis of non-edible biodiesel from crude jatropha oil and used cooking oil
This study focuses on a feasibility study of alternative nonedible crude oil such as jatropha and used cooking oil in biodiesel production. Crude jatropha oil (CJO) and used cooking oil (UCO) were converted to biodiesel using a two-step transesterification process with presents of acid-based and alkaline-based catalysts. Each three biodiesel blends (B5, B15 and B25) have been produced by blended with conventional diesel fuel (CDF). Determination of the fuel properties for each blend including CDF, Jatropha Methyl Ester (JME) and Used Cooking Oil Methyl Ester (UCOME) have been carried out. The average yield for jatropha and used cooking oil biodiesels production was 94.3% and 92% respectively. The increment of the percentage of JME or UCOME in its blends is proportional to fuels physical properties such as density, specific gravity, kinematic viscosity and surface tension, however inversely proportional to fuels calorific value. Based on the results of this study, it is acceptable to conclude that non-edible CJO and UCO are viable alternatives to edible oil as feedstock to renewable fuel in order to reduce the greenhouse gases produced.
- 5 November 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 225, 06008
Open AccessSynthesis of non-edible biodiesel from crude jatropha oil and used cooking oil
This study focuses on a feasibility study of alternative nonedible crude oil such as jatropha and used cooking oil in biodiesel production. Crude jatropha oil (CJO) and used cooking oil (UCO) were converted to biodiesel using a two-step transesterification process with presents of acid-based and alkaline-based catalysts. Each three biodiesel blends (B5, B15 and B25) have been produced by blended with conventional diesel fuel (CDF). Determination of the fuel properties for each blend including CDF, Jatropha Methyl Ester (JME) and Used Cooking Oil Methyl Ester (UCOME) have been carried out. The average yield for jatropha and used cooking oil biodiesels production was 94.3% and 92% respectively. The increment of the percentage of JME or UCOME in its blends is proportional to fuels physical properties such as density, specific gravity, kinematic viscosity and surface tension, however inversely proportional to fuels calorific value. Based on the results of this study, it is acceptable to conclude that non-edible CJO and UCO are viable alternatives to edible oil as feedstock to renewable fuel in order to reduce the greenhouse gases produced.
- Open Access
- 20 November 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (7-3)
EFFECTS OF DUCT BURNER ON BOTTOMING CYCLE IN A COMBINED CYCLE POWER PLANT
In this study, thermodynamic modeling and exergoeconomic assessment of a Combined Cycle Power Plant (CCPP) with a Duct Burner (DB) was performed. Obtaining an optimum condition for the performance of a CCPP, using a DB after gas turbine was investigated by various researchers. DB is installed between gas turbine cycle and Rankine cycle of a CCPP to connect the gas turbine outlet to the Heat Recovery Steam Generator (HRSG) in order to produce steam for bottoming cycle. To find the irreversibility effect in each component of the bottoming cycle, a comprehensive parametric study is performed. In this regard, the effect of DB fuel flow rate on cost efficiency and economic of the bottoming cycle are investigated. To obtain a reasonable result, all the design parameters are kept constant while the DB fuel flow rate is varied. The results indicate that by increasing DB fuel flow rate, the investment cost and the efficiency of CCPP are increased. T-S diagram reveals that by using a DB, higher pressures steam in heat recovery steam generator has higher temperature while the low pressure is decreased. In addition, the exergy of flow gases in heat recovery steam generator increases. So, the exergy efficiency of the whole cycle was increased to around 6 percent, while the cost of the plant reduced by one percent.
- 20 November 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (7-3)
Open AccessEFFECTS OF DUCT BURNER ON BOTTOMING CYCLE IN A COMBINED CYCLE POWER PLANT
In this study, thermodynamic modeling and exergoeconomic assessment of a Combined Cycle Power Plant (CCPP) with a Duct Burner (DB) was performed. Obtaining an optimum condition for the performance of a CCPP, using a DB after gas turbine was investigated by various researchers. DB is installed between gas turbine cycle and Rankine cycle of a CCPP to connect the gas turbine outlet to the Heat Recovery Steam Generator (HRSG) in order to produce steam for bottoming cycle. To find the irreversibility effect in each component of the bottoming cycle, a comprehensive parametric study is performed. In this regard, the effect of DB fuel flow rate on cost efficiency and economic of the bottoming cycle are investigated. To obtain a reasonable result, all the design parameters are kept constant while the DB fuel flow rate is varied. The results indicate that by increasing DB fuel flow rate, the investment cost and the efficiency of CCPP are increased. T-S diagram reveals that by using a DB, higher pressures steam in heat recovery steam generator has higher temperature while the low pressure is decreased. In addition, the exergy of flow gases in heat recovery steam generator increases. So, the exergy efficiency of the whole cycle was increased to around 6 percent, while the cost of the plant reduced by one percent.
- Open Access
- 20 November 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (7-3)
EFFECT OF VARYING THE DOUBLE RADIAL SWIRLER CONFIGURATION ON THE FLUID DYNAMIC AND EMISSIONS PERFORMANCES IN A CAN COMBUSTOR
The main purpose of this article is to present the fluid dynamic and combustion performances of a can combustor applying double radial flow swirler. Analysis was conducted using Computational Fluid Dynamics simulation (CFD) and compared with experimental works conducted by previous researchers. Air pollution, in the form of gaseous emissions from gas turbine generator reportedly increasing every year. Design modifications was identified and used in this study where air swirler been proven able to reduce the formation rate of gaseous emission such as NOx and CO during combustion. Swirler in a burner is a device that serves to improve the air and fuel mixture in the main combustion zone. Swirlers, presently studied are from a combination of two radial swirlers with different vane angle (primary and secondary) such as 30o/40o, 30o/50o and 30o/60o. Application of Ansys Fluent 14 CFD solvers was used in this study. Turbulent flow model used was from Reynolds Average Navier-Stokes (RANS) type involving k-ϵ. The fuel used is diesel. The parameters studied were wall temperature distribution along the combustor, the volume of NOx and volume of CO in the main combustion zone. Results from this study showed that the combination of 30o/60o generates the lowest gaseous emissions production rate. The highest average percentage error obtained by simulation studies compared to the actual experimental values for NOx was 22% and CO was 17.8%. Comparison between simulation and actual study proves that the simulation method can be used for preliminary decision and able to be used as benchmark to determine which is the best swirler configuration.
- 20 November 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (7-3)
Open AccessEFFECT OF VARYING THE DOUBLE RADIAL SWIRLER CONFIGURATION ON THE FLUID DYNAMIC AND EMISSIONS PERFORMANCES IN A CAN COMBUSTOR
The main purpose of this article is to present the fluid dynamic and combustion performances of a can combustor applying double radial flow swirler. Analysis was conducted using Computational Fluid Dynamics simulation (CFD) and compared with experimental works conducted by previous researchers. Air pollution, in the form of gaseous emissions from gas turbine generator reportedly increasing every year. Design modifications was identified and used in this study where air swirler been proven able to reduce the formation rate of gaseous emission such as NOx and CO during combustion. Swirler in a burner is a device that serves to improve the air and fuel mixture in the main combustion zone. Swirlers, presently studied are from a combination of two radial swirlers with different vane angle (primary and secondary) such as 30o/40o, 30o/50o and 30o/60o. Application of Ansys Fluent 14 CFD solvers was used in this study. Turbulent flow model used was from Reynolds Average Navier-Stokes (RANS) type involving k-ϵ. The fuel used is diesel. The parameters studied were wall temperature distribution along the combustor, the volume of NOx and volume of CO in the main combustion zone. Results from this study showed that the combination of 30o/60o generates the lowest gaseous emissions production rate. The highest average percentage error obtained by simulation studies compared to the actual experimental values for NOx was 22% and CO was 17.8%. Comparison between simulation and actual study proves that the simulation method can be used for preliminary decision and able to be used as benchmark to determine which is the best swirler configuration.
- Open Access
Combustion and Emission Characteristics of Coconut-Based Biodiesel in a Liquid Fuel Burner
This paper presents an investigation on the combustion performance of different Coconut Methyl Ester (CME) biodiesel blends with Conventional Diesel Fuel (CDF) under B5 (5% CME, 95% CDF), B15 (15% CME, 85% CDF), and B25 (25% CME, 75% CDF) conditions. The performances of these fuels were evaluated based on the temperature profiles of the combustor wall and emission concentration of Oxides of Nitrogen (NOx), Sulphur Dioxide (SO2), and Carbon Monoxide (CO). The fuel properties of the CME biodiesel blends were measured and compared with CDF. All tested fuels were combusted using an open-ended combustion chamber at three different equivalence ratios, i.e., lean fuel to air mixture (Ф = 0.8), stoichiometry (Ф = 1.0), and rich fuel to air mixture (Ф =1.2), using a standard solid spray fuel nozzle. The results indicated that CME biodiesel blends combust at a lower temperature and produce less emission in comparison with CDF for all equivalence ratios. Moreover, the increase of CME content in biodiesel blends reduced the temperature of the combustor wall and the emission concentration. Results also proved that the utilization of biodiesel is beneficial to various industrial applications, especially in the transportation sector due to it being environmentally friendly, and serves as an alternative to petroleum diesel fuel.
Open AccessCombustion and Emission Characteristics of Coconut-Based Biodiesel in a Liquid Fuel Burner
This paper presents an investigation on the combustion performance of different Coconut Methyl Ester (CME) biodiesel blends with Conventional Diesel Fuel (CDF) under B5 (5% CME, 95% CDF), B15 (15% CME, 85% CDF), and B25 (25% CME, 75% CDF) conditions. The performances of these fuels were evaluated based on the temperature profiles of the combustor wall and emission concentration of Oxides of Nitrogen (NOx), Sulphur Dioxide (SO2), and Carbon Monoxide (CO). The fuel properties of the CME biodiesel blends were measured and compared with CDF. All tested fuels were combusted using an open-ended combustion chamber at three different equivalence ratios, i.e., lean fuel to air mixture (Ф = 0.8), stoichiometry (Ф = 1.0), and rich fuel to air mixture (Ф =1.2), using a standard solid spray fuel nozzle. The results indicated that CME biodiesel blends combust at a lower temperature and produce less emission in comparison with CDF for all equivalence ratios. Moreover, the increase of CME content in biodiesel blends reduced the temperature of the combustor wall and the emission concentration. Results also proved that the utilization of biodiesel is beneficial to various industrial applications, especially in the transportation sector due to it being environmentally friendly, and serves as an alternative to petroleum diesel fuel.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 38-43
Downdraft gasification of raw and torrefied palm kernel shell
Downdraft gasification is a potential method to produce biomass-based power suited for small-scaled power generation application. In the present study, a downdraft gasifier is used to gasify both raw and torrefied palm kernel shell (PKS). The properties of the palm kernel shells were characterised prior to gasification. Torrefaction of PKS was performed at the maximum temperature of 400 o C. Torrefied PKS shows lower moisture content by 4.8% as compared to raw kernel shell. Gasification of the feedstock showed that torrefied PKS produced higher amount of reactive syngas components, notably 16.4% CO and 9.25% H2 (by volume) than its raw counterpart. The total lower heating value of the syngas produced by torrefied PKS is 7.2 MJ/kg higher than that of raw PKS. Comparison of the temperature profiles within the gasifier for torrefied and raw PKS show distinct differences, with the temperature of the oxidation zone for raw and torrefied PKS being 1115 o C and 1138 o C at the equivalence ratio of 0.41 and 0.30, respectively. Although both feedstock show high potential for synthesis gas production, torrefied PKS produces syngas of higher LHV.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 38-43
Downdraft gasification of raw and torrefied palm kernel shell
Downdraft gasification is a potential method to produce biomass-based power suited for small-scaled power generation application. In the present study, a downdraft gasifier is used to gasify both raw and torrefied palm kernel shell (PKS). The properties of the palm kernel shells were characterised prior to gasification. Torrefaction of PKS was performed at the maximum temperature of 400 o C. Torrefied PKS shows lower moisture content by 4.8% as compared to raw kernel shell. Gasification of the feedstock showed that torrefied PKS produced higher amount of reactive syngas components, notably 16.4% CO and 9.25% H2 (by volume) than its raw counterpart. The total lower heating value of the syngas produced by torrefied PKS is 7.2 MJ/kg higher than that of raw PKS. Comparison of the temperature profiles within the gasifier for torrefied and raw PKS show distinct differences, with the temperature of the oxidation zone for raw and torrefied PKS being 1115 o C and 1138 o C at the equivalence ratio of 0.41 and 0.30, respectively. Although both feedstock show high potential for synthesis gas production, torrefied PKS produces syngas of higher LHV.
- Open Access
- 31 January 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (2)
KESAN SUDUT PUSARAN TERHADAP PEMBENTUKAN EMISI MENGGUNAKAN DWI PEMUSAR UDARA ALIRAN JEJARIAN
Combustion of liquid fuel sprays produces NOX, CO and other emissions that have an adverse impact on the environment and humans. This study is conducted to produce low-emission combustion with the use of double radial swirler. Swirling flow burning will enhance the mixing of fuel and air to produce a flame that is more stable and efficient. In this study, weak swirler with an angle of 30º is set as a primary swirler and strong swirlers each with an angle of 40º, 50º and 60º are set as the secondary swirler. Combinations of these swirlers helped the mixing of fuel and air during combustion. The results show, the combination of swirlers 30º/60º produced the highest temperature profile, the best flames, more stable and shorter than other combinations. NOX emissions for the combination of swirlers 30º/60º at stoichiometric are 15.6% lower than the combinations of swirlers 30º/40º. Other emissions such as CO, also shows 8.4% of reduction in the combination of swirlers 30º/60º. These results indicated that double swirlers helped in reducing emissions during combustion and also producing an environmentally friendly combustion system.
- 31 January 2017
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 79 (2)
Open AccessKESAN SUDUT PUSARAN TERHADAP PEMBENTUKAN EMISI MENGGUNAKAN DWI PEMUSAR UDARA ALIRAN JEJARIAN
Combustion of liquid fuel sprays produces NOX, CO and other emissions that have an adverse impact on the environment and humans. This study is conducted to produce low-emission combustion with the use of double radial swirler. Swirling flow burning will enhance the mixing of fuel and air to produce a flame that is more stable and efficient. In this study, weak swirler with an angle of 30º is set as a primary swirler and strong swirlers each with an angle of 40º, 50º and 60º are set as the secondary swirler. Combinations of these swirlers helped the mixing of fuel and air during combustion. The results show, the combination of swirlers 30º/60º produced the highest temperature profile, the best flames, more stable and shorter than other combinations. NOX emissions for the combination of swirlers 30º/60º at stoichiometric are 15.6% lower than the combinations of swirlers 30º/40º. Other emissions such as CO, also shows 8.4% of reduction in the combination of swirlers 30º/60º. These results indicated that double swirlers helped in reducing emissions during combustion and also producing an environmentally friendly combustion system.