A. S. Fayed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
A. S. Fayed has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
M.M.I. Hammouda
Mechanical Engineering Department Al‐Azhar University Nasr City Cairo Egypt
2 shared publications- Ashraf A. Ali
Department of Mechanical Design and Production Engineering, Faculty of Engineering, Zagazig University, Zagazig, Egypt
1 shared publication - Hossam E. M. Sallam
Materials Engineering Department, Zagazig University, Zagazig 44519, Egypt
1 shared publication K. A. Abu‐Hasel
Mechanical Engineering Department College of Engineering, University of Bisha Bisha Saudi Arabia
1 shared publicationM Hammouda
1 shared publication- Mohammad M. I. Hammouda
Department of Mechanical Engineering Al‐Azhar University Cairo Egypt
1 shared publication
Latest Publications
- Open Access
- 7 July 2025
- Published by Springer Nature in Journal of Umm Al-Qura University for Engineering and Architecture
- Vol. 16 (3) , 732-741
Fatigue crack growth correlations in structural elements under mixed mode loading: a review
Under mixed-mode loading conditions, fatigue failure of structures has depicted exceptional interest for its proximity to true engineering structures situations. Furthermore, the standard fracture test procedures for determination material’s fracture toughness are usually intended under pure mode I or for loading in tensile mode. Asserting a crack growth criterion under mixed mode conditions is vital for actual structural applications. Under such conditions, not only the direction of crack extent is important but also the rate of fatigue crack propagation. A number of parameters were proposed to cite fatigue crack growth rates under mixed-mode loading. For real structures or products, cyclic forces of various natures may be imposed upon a wide scale of conditions. The investigation of failure paths and crack instability criteria in mixed-mode failure scenarios presents significantly greater challenges than those encountered in pure mode I failure conditions. In this review, the most important fatigue crack growth rate correlations will be covered to identify how cracks grow under mixed-mode loading. A comprehensive examination of the relevant literature has been conducted. These parameters play a fundamental role in understanding fatigue crack growth rate phenomena and will contribute significantly to the development of enhanced safety and reliability in structural components across diverse industrial applications.
- 7 July 2025
- Published by Springer Nature in Journal of Umm Al-Qura University for Engineering and Architecture
- Vol. 16 (3) , 732-741
Open AccessFatigue crack growth correlations in structural elements under mixed mode loading: a review
Under mixed-mode loading conditions, fatigue failure of structures has depicted exceptional interest for its proximity to true engineering structures situations. Furthermore, the standard fracture test procedures for determination material’s fracture toughness are usually intended under pure mode I or for loading in tensile mode. Asserting a crack growth criterion under mixed mode conditions is vital for actual structural applications. Under such conditions, not only the direction of crack extent is important but also the rate of fatigue crack propagation. A number of parameters were proposed to cite fatigue crack growth rates under mixed-mode loading. For real structures or products, cyclic forces of various natures may be imposed upon a wide scale of conditions. The investigation of failure paths and crack instability criteria in mixed-mode failure scenarios presents significantly greater challenges than those encountered in pure mode I failure conditions. In this review, the most important fatigue crack growth rate correlations will be covered to identify how cracks grow under mixed-mode loading. A comprehensive examination of the relevant literature has been conducted. These parameters play a fundamental role in understanding fatigue crack growth rate phenomena and will contribute significantly to the development of enhanced safety and reliability in structural components across diverse industrial applications.
- Open Access
- 1 September 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (9) , 096501
Stress intensity factors of partially compressed centrally cracked disk with frictional crack surfaces
This work analytically calculates mixed-mode I/II stress intensity factors for an inclined central frictional crack in a Brazilian disc partially compressed with a uniform pressure. Wide-range controlling parameters are invoked. The analyzed parameters include the pressure angle, relative crack length, crack inclination, and friction coefficient between the two crack surfaces. For partially compressed discs, there exists a critical pressure angle at which a crack with any angle will experience pure II loading. This critical pressure angle is not affected by friction and decreases as the crack length increases. A crack of any angle becomes inactive once the pressure angle exceeds another critical value of pressure angle. This value decreases as the friction coefficient or/and crack length increases. The handling of frictional surfaces of short cracks is simplified. The analysis defines the conditions to have (1) the crack opened and (2) the two crack surfaces sticking. A close agreement is achieved with relevant findings in previous relevant investigations. The present results do not exist in relevant literature and are valuable in solving fracture mechanics problems of significance in relation to crack path in cracked brittle materials.
- 1 September 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (9) , 096501
Open AccessStress intensity factors of partially compressed centrally cracked disk with frictional crack surfaces
This work analytically calculates mixed-mode I/II stress intensity factors for an inclined central frictional crack in a Brazilian disc partially compressed with a uniform pressure. Wide-range controlling parameters are invoked. The analyzed parameters include the pressure angle, relative crack length, crack inclination, and friction coefficient between the two crack surfaces. For partially compressed discs, there exists a critical pressure angle at which a crack with any angle will experience pure II loading. This critical pressure angle is not affected by friction and decreases as the crack length increases. A crack of any angle becomes inactive once the pressure angle exceeds another critical value of pressure angle. This value decreases as the friction coefficient or/and crack length increases. The handling of frictional surfaces of short cracks is simplified. The analysis defines the conditions to have (1) the crack opened and (2) the two crack surfaces sticking. A close agreement is achieved with relevant findings in previous relevant investigations. The present results do not exist in relevant literature and are valuable in solving fracture mechanics problems of significance in relation to crack path in cracked brittle materials.
- 13 January 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (3) , 1462-1472
Morphological, mechanical, and thermal characterization of electrospun three‐dimensional graphite nanoplatelets/polystyrene ultra‐fine fibril composite fabrics
Ultra‐fine fibril composites were produced by electrospinning of a polymer solution containing polystyrene (PS)/dimethylformamide (DMF) with different concentrations of three‐dimensional graphite nanoplatelets (3D‐GNPs). Berry's number of PS/DMF polymer solution was extensively studied to produce minimum electrospun PS fiber diameters. Three‐dimensional GNPs of different weight percentages were dispersed in the optimized PS/DMF to produce ultrafine fibril composite fabric. The electrospun average diameters decreased from 1.5 μm for PS fibers to 890 nm for 3D‐GNPs/PS fibril composites, respectively, at 12 and 9.8 Berry's number. High‐resolution transmission electron microscopy samples' micrographs confirm a homogenous dispersion and alignment of 3D‐GNPs in PS fibril composites. Thermal and mechanical characteristics of fabrics were determined using thermogravimetric analysis, thermomechanical Analysis, and dynamic mechanical analysis (DMA). It was found that there was an increase in percentage elongation, tensile strength, thermal stability, and glass‐transition temperature for 3D‐GNPs PS fibril composite fabrics compared to PS fabrics. Diminishing the value of loss tangent, measured by DMA, was used as an approach to predict the maximum amount of 3D‐GNPs weight percent dispersion in electrospun PS/dimethylformamide solution. One of the most important potential applications of the electrospun 3D‐GNPs/PS fibril composite fabrics is in the interiors of vehicles and aerospace industries as it characterizes by its good thermal and mechanical properties as well as its low density.
- 13 January 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (3) , 1462-1472
Morphological, mechanical, and thermal characterization of electrospun three‐dimensional graphite nanoplatelets/polystyrene ultra‐fine fibril composite fabrics
Ultra‐fine fibril composites were produced by electrospinning of a polymer solution containing polystyrene (PS)/dimethylformamide (DMF) with different concentrations of three‐dimensional graphite nanoplatelets (3D‐GNPs). Berry's number of PS/DMF polymer solution was extensively studied to produce minimum electrospun PS fiber diameters. Three‐dimensional GNPs of different weight percentages were dispersed in the optimized PS/DMF to produce ultrafine fibril composite fabric. The electrospun average diameters decreased from 1.5 μm for PS fibers to 890 nm for 3D‐GNPs/PS fibril composites, respectively, at 12 and 9.8 Berry's number. High‐resolution transmission electron microscopy samples' micrographs confirm a homogenous dispersion and alignment of 3D‐GNPs in PS fibril composites. Thermal and mechanical characteristics of fabrics were determined using thermogravimetric analysis, thermomechanical Analysis, and dynamic mechanical analysis (DMA). It was found that there was an increase in percentage elongation, tensile strength, thermal stability, and glass‐transition temperature for 3D‐GNPs PS fibril composite fabrics compared to PS fabrics. Diminishing the value of loss tangent, measured by DMA, was used as an approach to predict the maximum amount of 3D‐GNPs weight percent dispersion in electrospun PS/dimethylformamide solution. One of the most important potential applications of the electrospun 3D‐GNPs/PS fibril composite fabrics is in the interiors of vehicles and aerospace industries as it characterizes by its good thermal and mechanical properties as well as its low density.
- 29 April 2019
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 44 (9) , 7667-7676
Numerical Analysis of Crack Initiation Direction in Quasi-brittle Materials: Effect of T-Stress
- 29 April 2019
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 44 (9) , 7667-7676
Numerical Analysis of Crack Initiation Direction in Quasi-brittle Materials: Effect of T-Stress
- 1 January 2018
- Published by Growing Science in Engineering Solid Mechanics
- p. 175-186
Numerical evaluation of mode I/II SIF of quasi-brittle materials using cracked semi-circular bend specimen
- 1 January 2018
- Published by Growing Science in Engineering Solid Mechanics
- p. 175-186
Numerical evaluation of mode I/II SIF of quasi-brittle materials using cracked semi-circular bend specimen
- 19 October 2017
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 41 (4) , 856-868
Modes I/II SIF of a diametrically compressed Brazilian disc having a central inclined crack with frictional surfaces
An in‐house finite element code was used to analyse a diametrically compressed isotropic homogeneous Brazilian disc having a central inclined crack with frictional surfaces for the evaluation of its corresponding modes I and II stress intensity factor (SIF). One‐half of the disc was successfully idealized. The coefficient of friction between the crack surfaces ranged from 0 to 1 in steps of 0.1. Relative crack length ratios of 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, and 0.7 were analysed with crack angles up to 90° in steps of 5°.The crack angle corresponding to the transition from a mixed mode I/II to a pure mode II decreases with increasing the relative crack length ratio. An increase in the relative crack length ratio leads to an increase in the range of crack angles corresponding to a partially closed crack. The crack angle at which fully closed sliding crack surfaces commences is 30° independent of the relative crack length ratio and the friction coefficient. With the same relative crack length ratio and increasing the friction coefficient, there is a corresponding decrease in the crack angle for the maximum mode II SIF. With a decrease in the relative crack length ratio or the friction coefficient, the crack angle beyond which the crack surfaces become in a fully sticking mode decreases resulting in zero mode II SIF. Generally, mode II SIF decreases with increasing the friction coefficient between the crack surfaces. Good agreement has been generally obtained with relevant results found in the literature.
- 19 October 2017
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 41 (4) , 856-868
Modes I/II SIF of a diametrically compressed Brazilian disc having a central inclined crack with frictional surfaces
An in‐house finite element code was used to analyse a diametrically compressed isotropic homogeneous Brazilian disc having a central inclined crack with frictional surfaces for the evaluation of its corresponding modes I and II stress intensity factor (SIF). One‐half of the disc was successfully idealized. The coefficient of friction between the crack surfaces ranged from 0 to 1 in steps of 0.1. Relative crack length ratios of 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, and 0.7 were analysed with crack angles up to 90° in steps of 5°.The crack angle corresponding to the transition from a mixed mode I/II to a pure mode II decreases with increasing the relative crack length ratio. An increase in the relative crack length ratio leads to an increase in the range of crack angles corresponding to a partially closed crack. The crack angle at which fully closed sliding crack surfaces commences is 30° independent of the relative crack length ratio and the friction coefficient. With the same relative crack length ratio and increasing the friction coefficient, there is a corresponding decrease in the crack angle for the maximum mode II SIF. With a decrease in the relative crack length ratio or the friction coefficient, the crack angle beyond which the crack surfaces become in a fully sticking mode decreases resulting in zero mode II SIF. Generally, mode II SIF decreases with increasing the friction coefficient between the crack surfaces. Good agreement has been generally obtained with relevant results found in the literature.
- 1 January 2017
- Published by Growing Science in Engineering Solid Mechanics
- p. 61-70
Numerical analysis of mixed mode I/II stress intensity factors of edge slant cracked plates
- 1 January 2017
- Published by Growing Science in Engineering Solid Mechanics
- p. 61-70
Numerical analysis of mixed mode I/II stress intensity factors of edge slant cracked plates
- 1 January 2007
- Published by Elsevier in International Journal of Fatigue
- Vol. 29 (1) , 30-48
Modelling of cracking sites/development in axial dovetail joints of aero-engine compressor discs
- 1 January 2007
- Published by Elsevier in International Journal of Fatigue
- Vol. 29 (1) , 30-48
Modelling of cracking sites/development in axial dovetail joints of aero-engine compressor discs
- 1 September 2004
- Published by Springer Nature in International Journal of Fracture
- Vol. 129 (2) , 141-148
Stress intensity factors of a central slant crack with frictional surfaces in plates with biaxial loading
- 1 September 2004
- Published by Springer Nature in International Journal of Fracture
- Vol. 129 (2) , 141-148
Stress intensity factors of a central slant crack with frictional surfaces in plates with biaxial loading