Rocco Lagioia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rocco Lagioia has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Panteghini
DICATAM University of Brescia Brescia Italy
11 shared publications - Alexander M. Puzrin
Institute for Geotechnical Engineering, ETH Zürich, Stefano-Franscini-Platz 5, 8093, Zürich, Switzerland
2 shared publications - Francesco Colleselli
Department of Civil Engineering, University of Brescia, Brescia, Italy
2 shared publications R. Nova
Milan University of Technology
2 shared publicationsA. Coviello
Milan University of Technology
1 shared publication- Alex Sanzeni
DICATAM, Università degli Studi di Brescia, Brescia, Italy
1 shared publication
Latest Publications
- 30 May 2022
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 46 (12) , 2233-2267
An implicit integration algorithm based on invariants for isotropic elasto‐plastic models of the Cosserat continuum
A Finite Element (FE) procedure based on a fully implicit backward Euler predictor/corrector scheme for the Cosserat continuum is here presented. The integration algorithm is suitable for yield and plastic potential surfaces with general shape in the deviatoric plane. The key element of the integration scheme is the spectral decomposition of the stress tensor, which is achieved, despite the lack of symmetry, because of the mathematical structure of the yield function and the set of invariants chosen as independent variables. It is also shown that the choice of invariants enables considerable mathematical simplifications, which result in the reduction of the system of equations and unknowns of the elasto‐plastic problem from 19 to 1, and to rigorously handle the discontinuity at the apex of the surfaces. The algorithm has been implemented in a proprietary FE programme, and used for the constitutive model recently proposed by the same authors in this journal for the Cosserat continuum, which allows to set various classical failure criteria as yield and plastic potential surfaces. Numerical analyses have been conducted to simulate a biaxial compression test and a shallow strip footing resting on a Tresca, Mohr–Coulomb, Matsuoka–Nakai and Lade–Duncan soil. The benefits of the Cosserat continuum over the Cauchy/Maxwell medium are discussed considering mesh refinement, non‐associated flow and softening behaviour.
- 30 May 2022
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 46 (12) , 2233-2267
An implicit integration algorithm based on invariants for isotropic elasto‐plastic models of the Cosserat continuum
A Finite Element (FE) procedure based on a fully implicit backward Euler predictor/corrector scheme for the Cosserat continuum is here presented. The integration algorithm is suitable for yield and plastic potential surfaces with general shape in the deviatoric plane. The key element of the integration scheme is the spectral decomposition of the stress tensor, which is achieved, despite the lack of symmetry, because of the mathematical structure of the yield function and the set of invariants chosen as independent variables. It is also shown that the choice of invariants enables considerable mathematical simplifications, which result in the reduction of the system of equations and unknowns of the elasto‐plastic problem from 19 to 1, and to rigorously handle the discontinuity at the apex of the surfaces. The algorithm has been implemented in a proprietary FE programme, and used for the constitutive model recently proposed by the same authors in this journal for the Cosserat continuum, which allows to set various classical failure criteria as yield and plastic potential surfaces. Numerical analyses have been conducted to simulate a biaxial compression test and a shallow strip footing resting on a Tresca, Mohr–Coulomb, Matsuoka–Nakai and Lade–Duncan soil. The benefits of the Cosserat continuum over the Cauchy/Maxwell medium are discussed considering mesh refinement, non‐associated flow and softening behaviour.
- 22 December 2021
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 46 (4) , 674-696
A micropolar isotropic plasticity formulation for non‐associated flow rule and softening featuring multiple classical yield criteria
The Cosserat continuum is very effective in regularizing the ill‐posed governing equations of the Cauchy/Maxwell continuum. An elasto‐plastic constitutive model for the linear formulation of the Cosserat continuum is here presented, which features non‐associated flow, hardening/softening behaviour and multiple yield and plastic potential surfaces, whilst linear hyper‐elasticity is adopted to reproduce the recoverable response. For the definition of the yield and plastic potential functions, the equivalent von Mises stress is formulated using energy considerations and the theory of representations, the latter being also used to retrieve an expression for the Lode's angle. The recent Generalized classical criterion is then used to define the yield and plastic potential functions so that Lode's angle‐dependent deviatoric sections can be used.
- 22 December 2021
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 46 (4) , 674-696
A micropolar isotropic plasticity formulation for non‐associated flow rule and softening featuring multiple classical yield criteria
The Cosserat continuum is very effective in regularizing the ill‐posed governing equations of the Cauchy/Maxwell continuum. An elasto‐plastic constitutive model for the linear formulation of the Cosserat continuum is here presented, which features non‐associated flow, hardening/softening behaviour and multiple yield and plastic potential surfaces, whilst linear hyper‐elasticity is adopted to reproduce the recoverable response. For the definition of the yield and plastic potential functions, the equivalent von Mises stress is formulated using energy considerations and the theory of representations, the latter being also used to retrieve an expression for the Lode's angle. The recent Generalized classical criterion is then used to define the yield and plastic potential functions so that Lode's angle‐dependent deviatoric sections can be used.
- 27 May 2019
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 43 (11) , 1978-1994
The difficult challenge of modelling the non‐linear elastic behaviour of soils within a theoretically sound framework
Summary: Hypo‐elastic relations are often adopted to simulate the recoverable non‐linear behaviour of soils within elasto‐plastic constitutive models. In reality, they are unable to reproduce the elastic, ie, recoverable, response of materials; hence, they introduce severe inconsistencies in models based on the decomposition of the total strain tensor into its recoverable and permanent parts. Hyper‐elasticity should then be used. However, existing models developed within this framework do not satisfy a number of fundamental theoretical requirements. A new hyper‐elastic model is proposed, which is rigourously formulated by integrating some of the main relations which emerge from experimental results. The model satisfies all theoretical requirements and also possesses features that are fundamental for its numerical integration. The model can be considered as the correct hyper‐elastic version of the classical hypo‐elastic constitutive relation adopted in models based on the Critical State framework, such as the Modified Cam‐Clay, with a constant Poisson's ratio.
- 27 May 2019
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 43 (11) , 1978-1994
The difficult challenge of modelling the non‐linear elastic behaviour of soils within a theoretically sound framework
Summary: Hypo‐elastic relations are often adopted to simulate the recoverable non‐linear behaviour of soils within elasto‐plastic constitutive models. In reality, they are unable to reproduce the elastic, ie, recoverable, response of materials; hence, they introduce severe inconsistencies in models based on the decomposition of the total strain tensor into its recoverable and permanent parts. Hyper‐elasticity should then be used. However, existing models developed within this framework do not satisfy a number of fundamental theoretical requirements. A new hyper‐elastic model is proposed, which is rigourously formulated by integrating some of the main relations which emerge from experimental results. The model satisfies all theoretical requirements and also possesses features that are fundamental for its numerical integration. The model can be considered as the correct hyper‐elastic version of the classical hypo‐elastic constitutive relation adopted in models based on the Critical State framework, such as the Modified Cam‐Clay, with a constant Poisson's ratio.
- 19 January 2018
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 42 (6) , 829-855
An approach for providing quasi‐convexity to yield functions and a generalized implicit integration scheme for isotropic constitutive models based on 2 unknowns
Summary: Yield and plastic potential surfaces are often affected by problems related to convexity. One such problem is encountered when the yield surface that bounds the elastic domain is itself convex; however, convexity is lost when the surface expands to pass through stress points outside the current elastic domain. In this paper, a technique is proposed, which effectively corrects this problem by providing linear homothetic expansion with respect to the centre of the yield surface. A very compact implicit integration scheme is also presented, which is of general applicability for isotropic constitutive models, provided that their yield and plastic potential functions are based on a separate mathematical definition of the meridional and deviatoric sections and that stress invariants are adopted as mechanical quantities. The elastic predictor‐plastic corrector algorithm is based on the solution of a system of 2 equations in 2 unknowns only. This further reduces to a single equation and unknown in the case of yield and plastic potential surfaces with a linear meridional section. The effectiveness of the proposed convexification technique and the efficiency and stability of the integration scheme are investigated by running numerical analyses of a notoriously demanding boundary value problem.
- 19 January 2018
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 42 (6) , 829-855
An approach for providing quasi‐convexity to yield functions and a generalized implicit integration scheme for isotropic constitutive models based on 2 unknowns
Summary: Yield and plastic potential surfaces are often affected by problems related to convexity. One such problem is encountered when the yield surface that bounds the elastic domain is itself convex; however, convexity is lost when the surface expands to pass through stress points outside the current elastic domain. In this paper, a technique is proposed, which effectively corrects this problem by providing linear homothetic expansion with respect to the centre of the yield surface. A very compact implicit integration scheme is also presented, which is of general applicability for isotropic constitutive models, provided that their yield and plastic potential functions are based on a separate mathematical definition of the meridional and deviatoric sections and that stress invariants are adopted as mechanical quantities. The elastic predictor‐plastic corrector algorithm is based on the solution of a system of 2 equations in 2 unknowns only. This further reduces to a single equation and unknown in the case of yield and plastic potential surfaces with a linear meridional section. The effectiveness of the proposed convexification technique and the efficiency and stability of the integration scheme are investigated by running numerical analyses of a notoriously demanding boundary value problem.
- 4 October 2017
- Published by Emerald Publishing in Géotechnique
- Vol. 68 (7) , 1-12
An extended modified Cam-Clay yield surface for arbitrary meridional and deviatoric shapes retaining full convexity and double homothety
This paper presents a new yield function, defined in terms of stress invariants and suitable for isotropic geomaterials. It is a generalization of that of the Modified Cam-Clay model and as such it retains all the mathematical advantages of the original formulation which are particularly convenient for the numerical integration of the constitutive law. In addition the proposed function is capable of providing a wide range of shapes and it is therefore suitable for defining both the yield and the plastic potential surfaces. As compared to the original MCC ellipse, one additional parameter is introduced for defining the shape of the meridional section, which conveniently controls also the relative position of the Normal Compression and Critical State lines. In the deviatoric plane the function not only provides the exact shape of classical failure criteria, such as von Mises, Drucker-Prager, Matsuoka-Nakai, Lade-Duncan, Tresca and Mohr-Coulomb, but it is also capable of rounding the hexagons of the last two...
- 4 October 2017
- Published by Emerald Publishing in Géotechnique
- Vol. 68 (7) , 1-12
An extended modified Cam-Clay yield surface for arbitrary meridional and deviatoric shapes retaining full convexity and double homothety
This paper presents a new yield function, defined in terms of stress invariants and suitable for isotropic geomaterials. It is a generalization of that of the Modified Cam-Clay model and as such it retains all the mathematical advantages of the original formulation which are particularly convenient for the numerical integration of the constitutive law. In addition the proposed function is capable of providing a wide range of shapes and it is therefore suitable for defining both the yield and the plastic potential surfaces. As compared to the original MCC ellipse, one additional parameter is introduced for defining the shape of the meridional section, which conveniently controls also the relative position of the Normal Compression and Critical State lines. In the deviatoric plane the function not only provides the exact shape of classical failure criteria, such as von Mises, Drucker-Prager, Matsuoka-Nakai, Lade-Duncan, Tresca and Mohr-Coulomb, but it is also capable of rounding the hexagons of the last two...
- 1 June 2017
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 7 (2) , 184-189
Accounting for specific failure criteria in the slip-line method for plane strain problems
This paper presents an approach to use the method of characteristics in plane strain problems with failure criteria other than the Mohr–Coulomb and Tresca. Although the method is of general validity, an instance of application is presented for the evaluation of the vertical plastic collapse load of a rigid shallow strip footing resting on a purely frictional material with no lateral surcharge. A comparison with results from finite-element analyses confirms the correctness of the approach.
- 1 June 2017
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 7 (2) , 184-189
Accounting for specific failure criteria in the slip-line method for plane strain problems
This paper presents an approach to use the method of characteristics in plane strain problems with failure criteria other than the Mohr–Coulomb and Tresca. Although the method is of general validity, an instance of application is presented for the evaluation of the vertical plastic collapse load of a rigid shallow strip footing resting on a purely frictional material with no lateral surcharge. A comparison with results from finite-element analyses confirms the correctness of the approach.
- Open Access
- 1 January 2016
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 472 (2185) , 20150713
On the existence of a unique class of yield and failure criteria comprising Tresca, von Mises, Drucker–Prager, Mohr–Coulomb, Galileo–Rankine, Matsuoka–Nakai and Lade–Duncan
In this paper, it is mathematically demonstrated that classical yield and failure criteria such as Tresca, von Mises, Drucker–Prager, Mohr–Coulomb, Matsuoka–Nakai and Lade–Duncan are all defined by the same equation. This can be seen as one of the three solutions of a cubic equation of the principal stresses and suggests that all such criteria belong to a more general class of non-convex formulations which also comprises a recent generalization of the Galileo–Rankine criterion. The derived equation is always convex and can also provide a smooth approximation of continuity of at least class C 2 of the original Tresca and Mohr–Coulomb criteria. It is therefore free from all the limitations which restrain the use of some of them in numerical analyses. The mathematical structure of the presented equation is based on a separate definition of the meridional and deviatoric sections of the graphical representation of the criteria. This enables the use of an efficient implicit integration algorithm which results in a very short machine runtime even when demanding boundary value problems are analysed.
- 1 January 2016
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 472 (2185) , 20150713
Open AccessOn the existence of a unique class of yield and failure criteria comprising Tresca, von Mises, Drucker–Prager, Mohr–Coulomb, Galileo–Rankine, Matsuoka–Nakai and Lade–Duncan
In this paper, it is mathematically demonstrated that classical yield and failure criteria such as Tresca, von Mises, Drucker–Prager, Mohr–Coulomb, Matsuoka–Nakai and Lade–Duncan are all defined by the same equation. This can be seen as one of the three solutions of a cubic equation of the principal stresses and suggests that all such criteria belong to a more general class of non-convex formulations which also comprises a recent generalization of the Galileo–Rankine criterion. The derived equation is always convex and can also provide a smooth approximation of continuity of at least class C 2 of the original Tresca and Mohr–Coulomb criteria. It is therefore free from all the limitations which restrain the use of some of them in numerical analyses. The mathematical structure of the presented equation is based on a separate definition of the meridional and deviatoric sections of the graphical representation of the criteria. This enables the use of an efficient implicit integration algorithm which results in a very short machine runtime even when demanding boundary value problems are analysed.
- Open Access
- 8 December 2014
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 470 (2172) , 20140568
The ‘ I 3 ’ generalization of the Galileo–Rankine tension criterion
The paper presents a new tension failure criterion which generalizes the so-called Galileo–Rankine formulation. The criterion can be used as a component of the so-called perfectly no-tension model for masonry and cements as well as for establishing a tension cut-off in complex constitutive models for soils, granular materials and powders. The criterion is described by means of a very concise equation based on the third invariant of the stress tensor, approximating the boundaries of the compressive octant of the principal stress space. This sheds new light on the physical significance of the third invariant of the stress tensor. The new criterion has been validated against two known analytical solutions for no-tension materials and also effectively applied for solving two geotechnical and structural engineering problems. The proposed formulation allows for an efficient implementation in finite-element programmes, removing some of the numerical difficulties associated with the Galileo–Rankine criterion.
- 8 December 2014
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 470 (2172) , 20140568
Open AccessThe ‘ I 3 ’ generalization of the Galileo–Rankine tension criterion
The paper presents a new tension failure criterion which generalizes the so-called Galileo–Rankine formulation. The criterion can be used as a component of the so-called perfectly no-tension model for masonry and cements as well as for establishing a tension cut-off in complex constitutive models for soils, granular materials and powders. The criterion is described by means of a very concise equation based on the third invariant of the stress tensor, approximating the boundaries of the compressive octant of the principal stress space. This sheds new light on the physical significance of the third invariant of the stress tensor. The new criterion has been validated against two known analytical solutions for no-tension materials and also effectively applied for solving two geotechnical and structural engineering problems. The proposed formulation allows for an efficient implementation in finite-element programmes, removing some of the numerical difficulties associated with the Galileo–Rankine criterion.
- 17 October 2013
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 38 (8) , 844-862
The influence of the plastic potential on plane strain failure
SUMMARY: The influence of the shape of the plastic potential in the deviatoric plane on plane strain collapse is investigated. The most commonly employed elastic‐perfect plastic models are considered, which adopt well‐known failure criteria for defining the yield and plastic potential surfaces, namely the von Mises, the Drucker–Prager, the Tresca, the Mohr–Coulomb and the Matsuoka–Nakai criteria. Finally, the conclusions are also extended to strain hardening/softening models. For simple constitutive models based on perfect plasticity, it is shown that the value of the Lode's angle at plastic collapse in plane strain conditions strongly depends on the specific failure surface adopted for reproducing the plastic potential surface. If the value of the Lode's angle at yield coincides with the failure value prescribed by the plastic potential, the stress–strain curves exhibit the typical perfect plastic behaviour with yield coinciding with failure, otherwise the stress changes after yield and the stress‐strain curves resemble those of strain hardening/softening models. The infinite strength which is in some situations exhibited by the Drucker–Prager model in plane strain condition is investigated and explained, and it is shown that this can also affect strain hardening/softening models. Copyright © 2013 John Wiley & Sons, Ltd.
- 17 October 2013
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 38 (8) , 844-862
The influence of the plastic potential on plane strain failure
SUMMARY: The influence of the shape of the plastic potential in the deviatoric plane on plane strain collapse is investigated. The most commonly employed elastic‐perfect plastic models are considered, which adopt well‐known failure criteria for defining the yield and plastic potential surfaces, namely the von Mises, the Drucker–Prager, the Tresca, the Mohr–Coulomb and the Matsuoka–Nakai criteria. Finally, the conclusions are also extended to strain hardening/softening models. For simple constitutive models based on perfect plasticity, it is shown that the value of the Lode's angle at plastic collapse in plane strain conditions strongly depends on the specific failure surface adopted for reproducing the plastic potential surface. If the value of the Lode's angle at yield coincides with the failure value prescribed by the plastic potential, the stress–strain curves exhibit the typical perfect plastic behaviour with yield coinciding with failure, otherwise the stress changes after yield and the stress‐strain curves resemble those of strain hardening/softening models. The infinite strength which is in some situations exhibited by the Drucker–Prager model in plane strain condition is investigated and explained, and it is shown that this can also affect strain hardening/softening models. Copyright © 2013 John Wiley & Sons, Ltd.
- 10 September 2013
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 38 (6) , 593-614
A fully convex reformulation of the original Matsuoka–Nakai failure criterion and its implicit numerically efficient integration algorithm
SUMMARY: This paper presents a reformulation of the original Matsuoka–Nakai criterion for overcoming the limitations which make its use in a stress point algorithm problematic. In fact, its graphical representation in the principal stress space is not convex as it comprises more branches, plotting also in negative octants, and it does not increase monotonically as the distance of the stress point from the failure surface rises. The proposed mathematical reformulation plots as a single, convex surface, which entirely lies in the positive octant of the stress space and evaluates to a quantity which monotonically increases as the stress point moves away from the failure surface. It is an exact reproduction, and not an approximated one, of the only significant branch of the original criterion. It is also suitable for shaping in the deviatoric plane the yield and plastic potential surfaces of complex constitutive models. A very efficient numerical algorithm for the implicit integration of the proposed formulation is presented, which enables the evaluation of the stress at the end of each increment by solving a single scalar equation, both for associated and non‐associated plasticity. The algorithm can be easily adapted for other smooth surfaces with linear meridian section. Finally, a close expression of the consistent Jacobian matrix is given for achieving quadratic convergence in the external structural newton loop. It is shown that all this results in extremely fast solutions of boundary value problems. Copyright © 2013 John Wiley & Sons, Ltd.
- 10 September 2013
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 38 (6) , 593-614
A fully convex reformulation of the original Matsuoka–Nakai failure criterion and its implicit numerically efficient integration algorithm
SUMMARY: This paper presents a reformulation of the original Matsuoka–Nakai criterion for overcoming the limitations which make its use in a stress point algorithm problematic. In fact, its graphical representation in the principal stress space is not convex as it comprises more branches, plotting also in negative octants, and it does not increase monotonically as the distance of the stress point from the failure surface rises. The proposed mathematical reformulation plots as a single, convex surface, which entirely lies in the positive octant of the stress space and evaluates to a quantity which monotonically increases as the stress point moves away from the failure surface. It is an exact reproduction, and not an approximated one, of the only significant branch of the original criterion. It is also suitable for shaping in the deviatoric plane the yield and plastic potential surfaces of complex constitutive models. A very efficient numerical algorithm for the implicit integration of the proposed formulation is presented, which enables the evaluation of the stress at the end of each increment by solving a single scalar equation, both for associated and non‐associated plasticity. The algorithm can be easily adapted for other smooth surfaces with linear meridian section. Finally, a close expression of the consistent Jacobian matrix is given for achieving quadratic convergence in the external structural newton loop. It is shown that all this results in extremely fast solutions of boundary value problems. Copyright © 2013 John Wiley & Sons, Ltd.