RPRikesh Patel

Rikesh Patel

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rikesh Patel has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    In situ monitoring of the annealing process using Spatially Resolved Acoustic Spectroscopy

    by Carolina Guerra, Wenqi Li, Rafael Fuentes-Domínguez, Peng Jin, Arthur Ford, Rikesh Patel, Matt Clark, Richard J. Smith

  • Open Access

    Conversion between longitudinal and shear waves at normal incidence using tailored meta-structures

    by Matt Clark, Rafael Fuentes-Domínguez, Peng Jin, Rikesh Patel, Marco Simonelli, Richard J. Smith


  • Open Access

    Imaging Microstructure on Optically Rough Surfaces Using Spatially Resolved Acoustic Spectroscopy

    by Wenqi Li, Paul Dryburgh, Don Pieris, Rikesh Patel, Matt Clark, Richard J. Smith

    The microstructure of a material defines many of its mechanical properties. Tracking the microstructure of parts during their manufacturing is needed to ensure the designed performance can be obtained, especially for additively manufactured parts. Measuring the microstructure non-destructively on real parts is challenging for optical techniques such as laser ultrasound, as the optically rough surface impacts the ability to generate and detect acoustic waves. Spatially resolved acoustic spectroscopy can be used to measure the microstructure, and this paper presents the capability on a range of surface finishes. We discuss how to describe ’roughness’ and how this influences the measurements. We demonstrate that measurements can be made on surfaces with Ra up to 28 μm for a selection of roughness comparators. Velocity images on a range of real surface finishes, including machined, etched, and additively manufactured finishes in an as-deposited state, are presented. We conclude that the Ra is a poor descriptor for the ability to perform measurements as the correlation length of the roughness has a large impact on the ability to detected the surface waves. Despite this issue, a wide range of real industrially relevant surface conditions can be measured.


  • Simple method of measuring thicknesses of surface-hardened layers by laser ultrasonic technique

    by Yong Lee, So Kitazawa, Rikesh Patel

    We proposed a simple non-contact inspection method using a laser ultrasonic technique to measure the thickness of a surface-hardened layer. This measurement is based on the dependence of a surface-wave velocity on the thickness of the hardened layers. In this case, it is essential to measure the surface-wave velocity with a wavelength comparable to the thickness of a hardened layer. However, it is not easy to selectively generate the surface waves with a desired wavelength. Thus we proposed the method where the surface waves with a desired wavelength are extracted using bandpass electrical filters. This method is simpler than the conventional one based on dispersion because the surface-wave velocity is directly obtained from measured temporal waveforms. We applied the method to measure the thickness of hardened layers and showed that the results were in good agreement with that obtained by the conventional method and numerical results.


  • Open Access

    Single pixel camera methodologies for spatially resolved acoustic spectroscopy

    by Rikesh Patel, Steve D. Sharples, Matt Clark, Mike G. Somekh, Wenqi Li

    Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasound technique used to determine the crystallographic orientation (i.e., microstructure) of materials through the generation and measurement of surface acoustic wave velocity on a sample. Previous implementations have used a grating pattern imaged onto the surface to control the frequency of the generated wave in a single direction—grain orientation can be computed by acquiring wave velocities in different directions on the surface (gathered by physically rotating the grating pattern). This paper reports an advance to this methodology, inspired by single pixel cameras, using a coded grating pattern, created using a spatial light modulator, to excite surface acoustic waves in multiple directions simultaneously. This change to the optical arrangement can simplify the overall system alignment, remove mechanical complexities, and is well suited for point-by-point full orientation imaging, potentially allowing for faster orientation imaging using SRAS microscopy. Improvements to the robustness of measurement may be expected to extend the applicability of SRAS in the materials science field. To demonstrate this methodology, experiments were conducted on isotropic and anisotropic samples.

  • Open Access

    Spatially Resolved Acoustic Spectroscopy Towards Online Inspection of Additive Manufacturing

    by D Pieris, R Patel, P Dryburgh, M Hirsch, W Li, S D Sharples, R J Smith, A T Clare, M Clark

    High-integrity engineering applications such as aerospace will not permit the incorporation of components containing any structural defects. The current generation of additive manufacturing (AM) platforms yield components with relatively high levels of defects. The in-line inspection of components built using AM can provide closed-loop feedback and vary build parameters during fabrication to minimise defects. This article reviews the capability of spatially resolved acoustic spectroscopy (SRAS) to be used as an inspection tool for detecting defects and characterising microstructure in parts induced by variations in build parameters. The authors first correlated changes to surface acoustic wave velocity and an increase in defects to variations in build laser power, then identified changes to the component microstructure caused by variations in build laser scan strategy. This was carried out using the detected probe light intensity and the measured surface acoustic velocity.


  • Open Access

    Imaging Material Texture of As-Deposited Selective Laser Melted Parts Using Spatially Resolved Acoustic Spectroscopy

    by Rikesh Patel, Matthias Hirsch, Paul Dryburgh, Don Pieris, Samuel Achamfuo-Yeboah, Richard Smith, Roger Light, Steve Sharples, Adam Clare, Matt Clark

    Additive manufacturing (AM) is a production technology where material is accumulated to create a structure, often through added shaped layers. The major advantage of additive manufacturing is in creating unique and complex parts for use in areas where conventional manufacturing reaches its limitations. However, the current class of AM systems produce parts that contain structural defects (e.g., cracks and pores) which is not compatible with certification in high value industries. The probable complexity of an AM design increases the difficulty of using many non-destructive evaluation (NDE) techniques to inspect AM parts—however, a unique opportunity exists to interrogate a part during production using a rapid surface based technique. Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasound inspection technique used to image material microstructure of metals and alloys. SRAS generates and detects `controlled’ surface acoustic waves (SAWs) using lasers, which makes it a non-contact and non-destructive technique. The technique is also sensitive to surface and subsurface voids. Work until now has been on imaging the texture information of selective laser melted (SLM) parts once prepared (i.e., polished with R a < 0.1 μ m)—the challenge for performing laser ultrasonics in-process is measuring waves on the rough surfaces present on as-deposited parts. This paper presents the results of a prototype SRAS system, developed using the rough surface ultrasound detector known as speckle knife edge detector (SKED)—texture images using this setup of an as-deposited Ti64 SLM sample, with a surface roughness of S a ≈ 6 μ m, were obtained.


  • Open Access

    Orientation imaging of macro-sized polysilicon grains on wafers using spatially resolved acoustic spectroscopy

    by Rikesh Patel, Wenqi Li, Richard J. Smith, Steve D. Sharples, Matt Clark


  • Open Access

    Enhanced sensing and conversion of ultrasonic Rayleigh waves by elastic metasurfaces

    by Andrea Colombi, Victoria Ageeva, Richard J. Smith, Adam Clare, Rikesh Patel, Matt Clark, Daniel Colquitt, Philippe Roux, Sebastien Guenneau, Richard V. Craster

    Recent years have heralded the introduction of metasurfaces that advantageously combine the vision of sub-wavelength wave manipulation, with the design, fabrication and size advantages associated with surface excitation. An important topic within metasurfaces is the tailored rainbow trapping and selective spatial frequency separation of electromagnetic and acoustic waves using graded metasurfaces. This frequency dependent trapping and spatial frequency segregation has implications for energy concentrators and associated energy harvesting, sensing and wave filtering techniques. Different demonstrations of acoustic and electromagnetic rainbow devices have been performed, however not for deep elastic substrates that support both shear and compressional waves, together with surface Rayleigh waves; these allow not only for Rayleigh wave rainbow effects to exist but also for mode conversion from surface into shear waves. Here we demonstrate experimentally not only elastic Rayleigh wave rainbow trapping, by taking advantage of a stop-band for surface waves, but also selective mode conversion of surface Rayleigh waves to shear waves. These experiments performed at ultrasonic frequencies, in the range of 400–600 kHz, are complemented by time domain numerical simulations. The metasurfaces we design are not limited to guided ultrasonic waves and are a general phenomenon in elastic waves that can be translated across scales.