MJMatthew Johnson

Matthew Johnson

*This is an algorithmically generated author record based on publicly available information.

Matthew Johnson has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental Comparison of Acoustic Characteristics for a High-Efficiency Magnetic Gearbox and a Mechanical Planetary Gearbox for Industrial HVAC Applications

    by Guanhua Tao, Bryton Praslicka, Shima Hasanpour, Thomas Simms, Zakki Wibisono, Matthew C. Gardner, Matthew Johnson, Emily Hankins, Maggie McCall, Alinoe Roussie, et al.

    In industrial fan applications, gearboxes or belt drives are often utilized to reduce the motor footprint to an acceptable level to maximize airflow. Customers demand fans with minimal noise and maintenance requirements, as well as a large mean time to failure (MTTF); however, mechanical gearboxes and belt drives are associated with high noise levels, significant maintenance requirements, and low MTTF rates, especially in harsh environments. This paper presents the development of a radial flux coaxial magnetic gear optimized for cost and modulator retention. The results reveal that sizable retaining features on the modulators' tangential sides may be employed while still maintaining high electromagnetic performance. A magnetic gear prototype was constructed and evaluated to determine its A-weighted acoustic noise characteristics. A similar commercial-off-the-shelf mechanical planetary gearbox was also evaluated to provide a benchmark for comparison with the magnetic gearbox. The results reveal the novel finding that the magnetic gearbox became quieter as the load increased, and the mechanical gearbox was louder than the magnetic gearbox at rated speed, except at very light loads. A second magnetic gearbox was also tested and proved to be louder than the mechanical gearbox; however, this second magnetic gearbox also became quieter as its load increased.


  • Cycloidal Reluctance Magnetic Gears for High Gear Ratio Applications

    by Shima Hasanpour, Matthew Johnson, Matthew C. Gardner, Hamid A. Toliyat

    At high gear ratios, surface permanent magnet (SPM) cycloidal magnetic gears (CyMGs) can achieve higher torque densities than SPM coaxial magnetic gears (CoMGs). This article introduces the radial flux reluctance CyMG (Rel CyMG) topology and its operating principles. The Rel CyMG replaces the permanent magnets (PMs) on an SPM CyMG’s inner rotor with salient teeth. Additionally, the Rel CyMG only requires half of the SPM CyMG’s outer rotor PM count to achieve the same gear ratio, which simplifies assembly and allows the use of wider magnets. This may improve high gear ratio designs’ manufacturability. A genetic algorithm (GA) was used with 2-D finite element analysis (FEA) to optimize Rel CyMGs, SPM CyMGs, and SPM CoMGs and demonstrate that SPM CyMGs significantly outperform the other topologies at higher gear ratios in terms of specific torque (ST) and PM ST. However, Rel CyMGs outperform SPM CoMGs at higher gear ratios, with respect to ST and PM ST. Rel CyMGs also eliminate the need for a PM retention sleeve and potentially enable the use of smaller air gaps, which can allow them to achieve slightly higher PM STs than SPM CyMGs at ultrahigh gear ratios. Employing Halbach arrays significantly improves both CyMG topologies’ ST.


  • A Parameterized Linear 3D Magnetic Equivalent Circuit for Analysis and Design of Radial Flux Magnetic Gears–Part II: Evaluation

    by Matthew Johnson, Matthew C. Gardner, Hamid A. Toliyat

    This is Part II of a two-part paper on the extension of a previously developed parameterized linear 2D magnetic equivalent circuit (MEC) for radial flux magnetic gears with surface permanent magnets to a 3D model. Part I explains the implementation of the 3D MEC. This section, Part II, evaluates the 3D MEC model's accuracy relative to 2D and 3D nonlinear finite element analysis (FEA) models. First, analysis of three base designs illustrates the impacts of the axial discretization parameters and stack length. This leads to the development of guidelines for selecting the axial discretization parameters. Additionally, the MEC is shown to accurately match 3D FEA in predicting the axial variation of flux densities. Finally, 3D MEC, 2D FEA, and 3D FEA models are deployed for a 144,000 case parametric study. The 2D FEA model significantly overpredicts the torques of designs with short stack lengths. However, the 3D MEC provides a much better agreement with 3D FEA, with less than 1% average absolute discrepancy. Additionally, the 3D MEC model is much faster than the 3D FEA model, with average 3D MEC model evaluation speeds ranging from about 100 times to 300 times faster than the 3D FEA for the base designs.


  • A Parameterized Linear 3D Magnetic Equivalent Circuit for Analysis and Design of Radial Flux Magnetic Gears–Part I: Implementation

    by Matthew Johnson, Matthew C. Gardner, Hamid A. Toliyat

    Magnetic gears can perform the same function as mechanical gears with the added benefits inherent to contactless power transfer. However, quick and accurate analysis tools are required for magnetic gears to reach their full potential. As end effects can significantly impact the slip torque of a magnetic gear, 2D models often overestimate the slip torques, so 3D models are frequently required. Therefore, this paper proposes a 3D linear Magnetic Equivalent Circuit (MEC) or reluctance network model of radial flux magnetic gears with surface mounted magnets. This is an extension of a previously developed 2D MEC model, and, like the previous 2D model, it is thoroughly parametrized so that it can be directly applied to a wide range of parametric cases. This is Part I of a two-part paper and focuses on the implementation of the 3D MEC model. Part II compares the 3D MEC model against nonlinear finite element analysis (FEA) models to validate the MEC model's accuracy and to develop guidelines for discretizing the geometry.


  • Optimization of Coaxial Magnetic Gear Design and Magnet Material Grade at Different Temperatures and Gear Ratios

    by Matthew C. Gardner, Bryton Praslicka, Matthew Johnson, Hamid A. Toliyat

    Magnetic gears, like mechanical gears, transform power between different speeds and torques; however, magnetic gears' contactless nature provides inherent potential benefits over mechanical gears. A genetic algorithm was used to optimize magnetic gears at different temperatures across a range of gear ratios. Using different magnet material grades on the different rotors and for the tangentially and radially magnetized magnets can slightly increase the specific torque relative to designs with a single magnet material. The high pole count rotor requires a magnet material with higher coercivity than that of the low pole count rotor magnet material, especially for designs with a large gear ratio. While increasing the temperature produces an exponential decay in the achievable specific torque, with a compounding reduction of about 0.4% for each degree Celsius, the temperature does not significantly affect the optimal geometric parameters and primarily affects the optimal materials. The gear ratio significantly affects the optimal geometric parameters and can impact the optimal magnet materials. Additionally, the genetic algorithm was employed to characterize the impact of stack length using 3D finite element analysis. Designs with shorter stack lengths favored thinner magnets and higher pole counts and may be able to use magnet materials with lower coercivities.


  • Review and Analysis of Coaxial Magnetic Gear Pole Pair Count Selection Effects

    by Bryton Praslicka, Matthew C. Gardner, Matthew Johnson, Hamid A. Toliyat

    Magnetic gears perform the same function as mechanical gears using magnetic fields instead of interlocking teeth. A review of the design processes used in the literature demonstrates that a critical design parameter, pole pair count, is often given inadequate consideration. In addition to reviewing the existing prototypes, this article uses a parametric simulation study to analyze the impacts of pole pair counts on gear performance and illustrate how the optimal pole counts vary with gear ratio and various design parameters. This article also introduces new ripple factors, which better correlate with torque ripple than the cogging factor ( $C_{T}$ ) used in previous articles, and illustrates why designs with noninteger gear ratios tend to have much smaller torque ripples than designs with integer gear ratios. While selecting the pole counts to minimize symmetry can reduce torque ripple, designs without any symmetry are shown to experience unbalanced magnetic forces on each rotor. Thus, it is recommended to select pole counts that result in an even number of modulators but not an integer gear ratio. This article also reveals that for a fixed gear ratio, a nontrivial optimum pole count minimizes the electromagnetic losses.


  • Analysis of High Gear Ratio Capabilities for Single-Stage, Series Multistage, and Compound Differential Coaxial Magnetic Gears

    by Matthew C. Gardner, Matthew Johnson, Hamid A. Toliyat

    Magnetic gears perform the same fundamental power conversion as mechanical gears. However, magnetic gears have significant potential benefits due to their noncontact operation. This paper compares three different ways to achieve high gear ratios using coaxial magnetic gears by evaluating trends for radial flux coaxial magnetic gears with surface mounted permanent magnets. First, a single-stage design can be used, but the torque density and efficiency both decline as the gear ratio increases. Additionally, the gear ratio achievable with a single-stage coaxial magnetic gear is limited by practical considerations, such as the maximum number of modulators and pole pairs that can be used within the given space. Second, a multistage design can be formed by connecting single-stage designs in series. Multistage designs can achieve much higher net gear ratios with much less of a torque density penalty, especially as the number of stages increases, but this entails greater complexity. Third, the compound differential coaxial magnetic gear (CDCMG) is proposed. The CDCMG is formed by interconnecting two single-stage coaxial magnetic gears and can achieve gear ratios much higher than the product of the gear ratios of the individual stages. However, the circulating power in the CDCMG leads to poor efficiencies.


  • Comparison of Surface Permanent Magnet Axial and Radial Flux Coaxial Magnetic Gears

    by Matthew C. Gardner, Matthew Johnson, Hamid A. Toliyat

    This paper provides a thorough, parametric comparison of axial and radial flux coaxial magnetic gears with surface-mounted permanent magnets (PMs). While both topologies share similar operating principles and can achieve comparable shear stresses, they exhibit different scaling trends with respect to key design parameters. Both topologies' volumetric torque densities (VTDs) increase with the outer radius, but the axial flux topology's VTD increases with the radius at a much faster rate than the radial flux topology's VTD. Another difference between the topologies involves their cross-sectional scaling parameters. The stack length axially scales radial flux gear cross-sections, and, as it increases, the impact of end-effects decreases, which improves the performance. For axial flux gears, the radii ratio scales the cross-section's radial width between different radii. This fundamentally changes optimal parameter values and design performance tradeoffs. Finally, axial flux rotors experience significant axial forces, but the radial forces on radial flux rotors can be balanced out. Based on these trends, radial flux gears are superior to axial flux gears for most applications; however, axial flux gears have a significant advantage when a large radius and a small axial length are permissible or when mechanical power needs to be transmitted across a flat barrier.


  • Design, Construction, and Analysis of a Large-Scale Inner Stator Radial Flux Magnetically Geared Generator for Wave Energy Conversion

    by Matthew Johnson, Matthew C. Gardner, Hamid A. Toliyat, Steven Englebretson, Wen Ouyang, Colin Tschida

    A magnetically geared machine (MGM) integrates a magnetic gear with a low torque, high speed electric machine to create a single compact high torque, low speed device with the size advantages of a mechanically geared system and the reliability of a direct drive machine. This work investigates the use of MGMs for wave energy conversion through the development of a large scale magnetically decoupled inner stator radial flux magnetically geared generator rated for 10 kW at an input speed of 30 rpm. Critical design trends are illustrated using parametric 2D and 3D finite element simulation results. Information is also provided about the prototype's mechanical structure and key magneto-mechanical design considerations, including the impact of modulator bridges and the extent of axially escaping leakage flux. The prototype's experimental stall torque of 3870 N-m represents a 99.1% match with the simulated stall torque and corresponds to volumetric and gravimetric torque densities of 82.8 kNμm/m$^{3}$ and 14.5 N-m/kg, respectively. Additionally, the prototype achieves an experimental efficiency of approximately 90% over much of its operating range.