Massimiliano Comotti
Research Interests
Massimiliano Comotti has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Cristina Della Pina
Dipartimento di Chimica Università degli Studi di Milano Milano Italy
8 shared publications - Michele Rossi
University of Milano
8 shared publications Ferdi Schüth
Heterogeneous Catalysis Department, Max Planck Institut für Kohlenforschung, Kaiser Wilhelm Platz 1, 45470 Mülheim an der Ruhr (Germany), Fax: (+49) 208-3062995
7 shared publications- Ferdi Schüth
Max‐Planck‐Institut für Kohlenforschung Mülheim an der Ruhr Germany
4 shared publications - Roberto Matarrese
Laboratory of Catalysis and Catalytic Processes, Department of Energy, Politecnico di Milano, Via La Masa 34, 20156 Milano, Italy
3 shared publications Wen-Cui Li
Max-Planck-Institut für Kohlenforschung, Mülheim an der Ruhr, Germany
3 shared publications
Latest Publications
- Top Cited Papers
- 1 September 2015
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 40 (33) , 10673-10686
Hydrogen generation system for ammonia–hydrogen fuelled internal combustion engines
- 1 September 2015
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 40 (33) , 10673-10686
Top Cited PapersHydrogen generation system for ammonia–hydrogen fuelled internal combustion engines
- 9 April 2015
- Published by Wiley in ChemCatChem
- Vol. 7 (9) , 1453-1459
Ammonia Decomposition over Iron Phthalocyanine‐Based Materials
Iron phthalocyanine‐based materials have been used herein as efficient catalysts for the ammonia decomposition reaction. These materials showed high activity, even superior to that showed by the commercial nickel‐based catalyst and iron‐doped carbon nanotubes, which were used as benchmarks in this study. Catalyst stability under reaction conditions appeared satisfactory, because no deactivation phenomena were observed. The type of the phthalocyanine precursor did not affect the catalytic performance; however, the preparation method had a strong effect. If the resulting material was exposed to the reaction conditions, some structural modification occurred. No clear correlation between phase composition and activity could be established because similar nitrogen content and similar crystalline domains in the sample led to different behaviors. However, the results of extensive characterization suggested that catalytic activities and conversion profiles were most likely dependent on material textural properties and thus on the preparation method used. The accessibility of iron species seems to be limited for catalysts prepared under vacuum. These phenomena are most likely responsible for the activation profile and for the low catalytic activity typical of these materials. In contrast, higher accessibility of iron species, typical of materials prepared under argon, would lead to improved and stable catalytic performance.
- 9 April 2015
- Published by Wiley in ChemCatChem
- Vol. 7 (9) , 1453-1459
Ammonia Decomposition over Iron Phthalocyanine‐Based Materials
Iron phthalocyanine‐based materials have been used herein as efficient catalysts for the ammonia decomposition reaction. These materials showed high activity, even superior to that showed by the commercial nickel‐based catalyst and iron‐doped carbon nanotubes, which were used as benchmarks in this study. Catalyst stability under reaction conditions appeared satisfactory, because no deactivation phenomena were observed. The type of the phthalocyanine precursor did not affect the catalytic performance; however, the preparation method had a strong effect. If the resulting material was exposed to the reaction conditions, some structural modification occurred. No clear correlation between phase composition and activity could be established because similar nitrogen content and similar crystalline domains in the sample led to different behaviors. However, the results of extensive characterization suggested that catalytic activities and conversion profiles were most likely dependent on material textural properties and thus on the preparation method used. The accessibility of iron species seems to be limited for catalysts prepared under vacuum. These phenomena are most likely responsible for the activation profile and for the low catalytic activity typical of these materials. In contrast, higher accessibility of iron species, typical of materials prepared under argon, would lead to improved and stable catalytic performance.
- 23 January 2014
- Published by Wiley in Angewandte Chemie
- Vol. 126 (5) , 1402-1405
Highly Efficient Platinum Group Metal Free Based Membrane‐Electrode Assembly for Anion Exchange Membrane Water Electrolysis
Low‐temperature electricity‐driven water splitting is an established technology for hydrogen production. However, the two main types, namely proton exchange membrane (PEM) and liquid alkaline electrolysis, have limitations. For instance, PEM electrolysis requires a high amount of costly platinum‐group‐metal (PGM) catalysts, and liquid alkaline electrolysis is not well suited for intermittent operation. Herein we report a highly efficient alkaline polymer electrolysis design, which uses a membrane‐electrode assembly (MEA) based on low‐cost transition‐metal catalysts and an anion exchange membrane (AEM). This system exhibited similar performance to the one achievable with PGM catalysts. Moreover, it is very suitable for intermittent power operation, durable, and able to efficiently operate at differential pressure up to 3 MPa. This system combines the benefits of PEM and liquid alkaline technologies allowing the scalable production of low‐cost hydrogen from renewable sources.
- 23 January 2014
- Published by Wiley in Angewandte Chemie
- Vol. 126 (5) , 1402-1405
Highly Efficient Platinum Group Metal Free Based Membrane‐Electrode Assembly for Anion Exchange Membrane Water Electrolysis
Low‐temperature electricity‐driven water splitting is an established technology for hydrogen production. However, the two main types, namely proton exchange membrane (PEM) and liquid alkaline electrolysis, have limitations. For instance, PEM electrolysis requires a high amount of costly platinum‐group‐metal (PGM) catalysts, and liquid alkaline electrolysis is not well suited for intermittent operation. Herein we report a highly efficient alkaline polymer electrolysis design, which uses a membrane‐electrode assembly (MEA) based on low‐cost transition‐metal catalysts and an anion exchange membrane (AEM). This system exhibited similar performance to the one achievable with PGM catalysts. Moreover, it is very suitable for intermittent power operation, durable, and able to efficiently operate at differential pressure up to 3 MPa. This system combines the benefits of PEM and liquid alkaline technologies allowing the scalable production of low‐cost hydrogen from renewable sources.
- 13 December 2013
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 53 (5) , 1378-1381
Highly Efficient Platinum Group Metal Free Based Membrane‐Electrode Assembly for Anion Exchange Membrane Water Electrolysis
Low‐temperature electricity‐driven water splitting is an established technology for hydrogen production. However, the two main types, namely proton exchange membrane (PEM) and liquid alkaline electrolysis, have limitations. For instance, PEM electrolysis requires a high amount of costly platinum‐group‐metal (PGM) catalysts, and liquid alkaline electrolysis is not well suited for intermittent operation. Herein we report a highly efficient alkaline polymer electrolysis design, which uses a membrane‐electrode assembly (MEA) based on low‐cost transition‐metal catalysts and an anion exchange membrane (AEM). This system exhibited similar performance to the one achievable with PGM catalysts. Moreover, it is very suitable for intermittent power operation, durable, and able to efficiently operate at differential pressure up to 3 MPa. This system combines the benefits of PEM and liquid alkaline technologies allowing the scalable production of low‐cost hydrogen from renewable sources.
- 13 December 2013
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 53 (5) , 1378-1381
Highly Efficient Platinum Group Metal Free Based Membrane‐Electrode Assembly for Anion Exchange Membrane Water Electrolysis
Low‐temperature electricity‐driven water splitting is an established technology for hydrogen production. However, the two main types, namely proton exchange membrane (PEM) and liquid alkaline electrolysis, have limitations. For instance, PEM electrolysis requires a high amount of costly platinum‐group‐metal (PGM) catalysts, and liquid alkaline electrolysis is not well suited for intermittent operation. Herein we report a highly efficient alkaline polymer electrolysis design, which uses a membrane‐electrode assembly (MEA) based on low‐cost transition‐metal catalysts and an anion exchange membrane (AEM). This system exhibited similar performance to the one achievable with PGM catalysts. Moreover, it is very suitable for intermittent power operation, durable, and able to efficiently operate at differential pressure up to 3 MPa. This system combines the benefits of PEM and liquid alkaline technologies allowing the scalable production of low‐cost hydrogen from renewable sources.
- 7 November 2012
- Published by Springer Nature
- p. 65-76
Experimental Results Using Ammonia Plus Hydrogen in a S.I. Engine
- 7 November 2012
- Published by Springer Nature
- p. 65-76
Experimental Results Using Ammonia Plus Hydrogen in a S.I. Engine
- 17 September 2010
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 132 (40) , 14152-14162
Spatially and Size Selective Synthesis of Fe-Based Nanoparticles on Ordered Mesoporous Supports as Highly Active and Stable Catalysts for Ammonia Decomposition
Uniform and highly dispersed γ-Fe2O3 nanoparticles with a diameter of ∼6 nm supported on CMK-5 carbons and C/SBA-15 composites were prepared via simple impregnation and thermal treatment. The nanostructures of these materials were characterized by XRD, Mössbauer spectroscopy, XPS, SEM, TEM, and nitrogen sorption. Due to the confinement effect of the mesoporous ordered matrices, γ-Fe2O3 nanoparticles were fully immobilized within the channels of the supports. Even at high Fe-loadings (up to about 12 wt %) on CMK-5 carbon no iron species were detected on the external surface of the carbon support by XPS analysis and electron microscopy. Fe2O3/CMK-5 showed the highest ammonia decomposition activity of all previously described Fe-based catalysts in this reaction. Complete ammonia decomposition was achieved at 700 °C and space velocities as high as 60 000 cm3 gcat−1 h−1. At a space velocity of 7500 cm3 gcat−1 h−1, complete ammonia conversion was maintained at 600 °C for 20 h. After the reaction, the immobilized γ-Fe2O3 nanoparticles were found to be converted to much smaller nanoparticles (γ-Fe2O3 and a small fraction of nitride), which were still embedded within the carbon matrix. The Fe2O3/CMK-5 catalyst is much more active than the benchmark NiO/Al2O3 catalyst at high space velocity, due to its highly developed mesoporosity. γ-Fe2O3 nanoparticles supported on carbon-silica composites are structurally much more stable over extended periods of time but less active than those supported on carbon. TEM observation reveals that iron-based nanoparticles penetrate through the carbon layer and then are anchored on the silica walls, thus preventing them from moving and sintering. In this way, the stability of the carbon-silica catalyst is improved. Comparison with the silica supported iron oxide catalyst reveals that the presence of a thin layer of carbon is essential for increased catalytic activity.
- 17 September 2010
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 132 (40) , 14152-14162
Spatially and Size Selective Synthesis of Fe-Based Nanoparticles on Ordered Mesoporous Supports as Highly Active and Stable Catalysts for Ammonia Decomposition
Uniform and highly dispersed γ-Fe2O3 nanoparticles with a diameter of ∼6 nm supported on CMK-5 carbons and C/SBA-15 composites were prepared via simple impregnation and thermal treatment. The nanostructures of these materials were characterized by XRD, Mössbauer spectroscopy, XPS, SEM, TEM, and nitrogen sorption. Due to the confinement effect of the mesoporous ordered matrices, γ-Fe2O3 nanoparticles were fully immobilized within the channels of the supports. Even at high Fe-loadings (up to about 12 wt %) on CMK-5 carbon no iron species were detected on the external surface of the carbon support by XPS analysis and electron microscopy. Fe2O3/CMK-5 showed the highest ammonia decomposition activity of all previously described Fe-based catalysts in this reaction. Complete ammonia decomposition was achieved at 700 °C and space velocities as high as 60 000 cm3 gcat−1 h−1. At a space velocity of 7500 cm3 gcat−1 h−1, complete ammonia conversion was maintained at 600 °C for 20 h. After the reaction, the immobilized γ-Fe2O3 nanoparticles were found to be converted to much smaller nanoparticles (γ-Fe2O3 and a small fraction of nitride), which were still embedded within the carbon matrix. The Fe2O3/CMK-5 catalyst is much more active than the benchmark NiO/Al2O3 catalyst at high space velocity, due to its highly developed mesoporosity. γ-Fe2O3 nanoparticles supported on carbon-silica composites are structurally much more stable over extended periods of time but less active than those supported on carbon. TEM observation reveals that iron-based nanoparticles penetrate through the carbon layer and then are anchored on the silica walls, thus preventing them from moving and sintering. In this way, the stability of the carbon-silica catalyst is improved. Comparison with the silica supported iron oxide catalyst reveals that the presence of a thin layer of carbon is essential for increased catalytic activity.
- Open Access
- 14 September 2010
- Published by Wiley in ChemCatChem
- Vol. 2 (9) , 1096-1106
Embedded Ru@ZrO2 Catalysts for H2 Production by Ammonia Decomposition
Ammonia can be used as fuel in internal combustion engines (ICEs). In this case, a flame accelerator, such as hydrogen, is needed. H2 can be produced on‐board by partial decomposition of ammonia. In this work, ruthenium nanoparticles were embedded into a lanthanum‐stabilized zirconia (LSZ) support to obtain active and stable heterogeneous catalysts for NH3 decomposition. The effects of the preparation of both Ru nanoparticles and LSZ support were investigated. The embedded catalysts present high metal dispersion and good metal accessibility. Despite the relatively low metal loading (3 wt %), activity was very high in the temperature range 400–600 °C. The activity of the reference catalysts prepared by using classical impregnation was significantly lower under the same working conditions. Although many factors contribute to the final catalyst performances, the data reported confirm that the embedding strategy minimizes the undesirable sintering of the Ru nanoparticles, leading to promising and stable catalytic activity.
- 14 September 2010
- Published by Wiley in ChemCatChem
- Vol. 2 (9) , 1096-1106
Open AccessEmbedded Ru@ZrO2 Catalysts for H2 Production by Ammonia Decomposition
Ammonia can be used as fuel in internal combustion engines (ICEs). In this case, a flame accelerator, such as hydrogen, is needed. H2 can be produced on‐board by partial decomposition of ammonia. In this work, ruthenium nanoparticles were embedded into a lanthanum‐stabilized zirconia (LSZ) support to obtain active and stable heterogeneous catalysts for NH3 decomposition. The effects of the preparation of both Ru nanoparticles and LSZ support were investigated. The embedded catalysts present high metal dispersion and good metal accessibility. Despite the relatively low metal loading (3 wt %), activity was very high in the temperature range 400–600 °C. The activity of the reference catalysts prepared by using classical impregnation was significantly lower under the same working conditions. Although many factors contribute to the final catalyst performances, the data reported confirm that the embedding strategy minimizes the undesirable sintering of the Ru nanoparticles, leading to promising and stable catalytic activity.
- 1 May 2009
- Published by Elsevier in Applied Catalysis A: General
- Vol. 359 (1-2) , 121-128
Au/ZnO as catalyst for methanol synthesis: The role of oxygen vacancies
- 1 May 2009
- Published by Elsevier in Applied Catalysis A: General
- Vol. 359 (1-2) , 121-128
Au/ZnO as catalyst for methanol synthesis: The role of oxygen vacancies
- 1 March 2009
- Published by Elsevier in Catalysis Today
- Vol. 141 (3-4) , 355-360
Effect of the titania morphology on the Au/TiO2-catalyzed aerobic epoxidation of stilbene
- 1 March 2009
- Published by Elsevier in Catalysis Today
- Vol. 141 (3-4) , 355-360
Effect of the titania morphology on the Au/TiO2-catalyzed aerobic epoxidation of stilbene