Tunmise Ayode Otitoju
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tunmise Ayode Otitoju has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Latif Ahmad
Universiti Sains Malaysia
7 shared publications - Sanxi Li
School of Environmental and Chemical Engineering Shenyang University of Technology Shenyang China
6 shared publications - Noor Fazliani Shoparwe
Universiti Malaysia Kelantan
5 shared publications Boon Seng Ooi
3 shared publications- Boon Seng Ooi
School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, 14300 Nibong Tebal, Pulau Pinang, Malaysia
3 shared publications - Patrick Ugochukwu Okoye
Instituto de Energías Renovables (IER-UNAM), Privada Xochicalco s/n Col. Centro, Temixco 62580, México
3 shared publications
Latest Publications
- Open Access
- 25 May 2024
- Published by Elsevier in Separation and Purification Technology
- Vol. 351, 128120
Controlling the polymorphs of PVDF membranes: Effects of a salt additive on PVDF polarization during phase separation processes
- 25 May 2024
- Published by Elsevier in Separation and Purification Technology
- Vol. 351, 128120
Open AccessControlling the polymorphs of PVDF membranes: Effects of a salt additive on PVDF polarization during phase separation processes
- Open Access
- 1 January 2024
- Published by Scientific Scholar in Journal of King Saud University – Science
- Vol. 36 (1)
Simultaneous removal of NH4+ and SO42− in Sulfate-reducing anammox scale reactor using FDAARGOS_798 strain/Anammox integration
In this study, an exploratory experiment conducted to assess the efficiency of time reducing Bacillus cereus FDAARGOS_798 strain in the Sulfate-reducing anaerobic ammonium oxidation –Sulfammox- process at lab-scale reactor. The sulfammox process was examine in four different semi-continuous stirred (SCS) reactors receiving a treated synthetic wastewaters by 1 % of FDAARGOS_798 strain acclimated and carried with 2 % anaerobic granular sludge (sludge) in the presence and absence of the 1 % anammox consortia granular sludge (Anammox). Subsequently, the previous work outcomes of optimized anaerobic acclimation method isolating FDAARGOS_798 strain. The SCS-2 reactor with sulfammox integration (FDAARGOS_798/Anammox) has shown significant performance in anoxic simultaneous removal of NH4 + and SO4 2-, 77 ± 0.2 % and 50 ± 1.0 %, respectively, with the sole substrate (NH4)2SO4 0.1 g/L. The NH4+ and SO42- average decrease of 40 ± 0.2 % and 46 ± 0.17 % in 26 days, respectively, in SCS-4 reactor treated by sulfammox (FDAARGOS_798/Anammox) in (NH4)2SO4 0.5 g/L. Subsequently, the N/S ratio is calculated at around 1.8 ± 0.2 as evidence of reaching sulfammox process. The sulfammox process could not detect at SCS-1and SCS-3 reactors which are in the absence of sulfammox integration. Meanwhile the exact sulfammox process pathway was not detectable due to complicated scenarios. In conclusion, the addition of Bacillus ceruse FDAARGOS_798 carried by Anammox consortium is a well indicate to an effective and economical way that accelerate the start-up of the sulfate-reducing anammox process.
- 1 January 2024
- Published by Scientific Scholar in Journal of King Saud University – Science
- Vol. 36 (1)
Open AccessSimultaneous removal of NH4+ and SO42− in Sulfate-reducing anammox scale reactor using FDAARGOS_798 strain/Anammox integration
In this study, an exploratory experiment conducted to assess the efficiency of time reducing Bacillus cereus FDAARGOS_798 strain in the Sulfate-reducing anaerobic ammonium oxidation –Sulfammox- process at lab-scale reactor. The sulfammox process was examine in four different semi-continuous stirred (SCS) reactors receiving a treated synthetic wastewaters by 1 % of FDAARGOS_798 strain acclimated and carried with 2 % anaerobic granular sludge (sludge) in the presence and absence of the 1 % anammox consortia granular sludge (Anammox). Subsequently, the previous work outcomes of optimized anaerobic acclimation method isolating FDAARGOS_798 strain. The SCS-2 reactor with sulfammox integration (FDAARGOS_798/Anammox) has shown significant performance in anoxic simultaneous removal of NH4 + and SO4 2-, 77 ± 0.2 % and 50 ± 1.0 %, respectively, with the sole substrate (NH4)2SO4 0.1 g/L. The NH4+ and SO42- average decrease of 40 ± 0.2 % and 46 ± 0.17 % in 26 days, respectively, in SCS-4 reactor treated by sulfammox (FDAARGOS_798/Anammox) in (NH4)2SO4 0.5 g/L. Subsequently, the N/S ratio is calculated at around 1.8 ± 0.2 as evidence of reaching sulfammox process. The sulfammox process could not detect at SCS-1and SCS-3 reactors which are in the absence of sulfammox integration. Meanwhile the exact sulfammox process pathway was not detectable due to complicated scenarios. In conclusion, the addition of Bacillus ceruse FDAARGOS_798 carried by Anammox consortium is a well indicate to an effective and economical way that accelerate the start-up of the sulfate-reducing anammox process.
- 19 May 2022
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 233 (6) , 1-15
Novel Simultaneous Removal of Ammonium and Sulfate by Isolated Bacillus cereus Strain from Sewage Treatment Plant
- 19 May 2022
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 233 (6) , 1-15
Novel Simultaneous Removal of Ammonium and Sulfate by Isolated Bacillus cereus Strain from Sewage Treatment Plant
- 5 January 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 336, 130379
Efficient removal of chemical oxygen demand from lye wastewater by APTES-TIO2/GO mixed matrix membrane: Optimization using Box-Behnken Design
- 5 January 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 336, 130379
Efficient removal of chemical oxygen demand from lye wastewater by APTES-TIO2/GO mixed matrix membrane: Optimization using Box-Behnken Design
- Open Access
Removal of Humic Acid Using 3-Methacryloxypropyl Trimethoxysilane Functionalized MWCNT Loaded TiO2/PES Hybrid Membrane
In the present work, a highly efficient mixed matrix membrane (MMM) for humic acid (HA) removal was developed. Multiwalled carbon nanotubes (MWCNTs) were functionalized in the presence of 3-methacryloxypropyl trimethoxysilane using the co-condensation method and were subsequently loaded with TiO2 (prepared via the sol–gel route). The as-prepared material was then incorporated into a PES polymer solution to prepare a fMWCNT-TiO2/PES hybrid membrane via non-solvent induced phase inversion. The microstructure of the membrane was characterized using Fourier transform infrared spectroscopy, atomic force microscopy, scanning electron microscopy, water contact angle, thickness, porosity, and pore size. The fMWCNT-TiO2/PES hybrid membrane was tested for the removal of HA and antifouling performance. The results show that the surface hydrophilicity of the membranes was greatly improved upon the addition of the fMWCNT-TiO2 particles. The results show that 92% of HA was effectively removed after 1 h of filtration. In comparison with pristine membrane, the incorporation of fMWCNT-TiO2 nanoparticles led to enhanced pure water flux (99.05 L/m2 h), permeate flux (62.01 L/m2 h), higher HA rejection (92%), and antifouling improvement (RFR: 37.40%, FRR: 86.02%). Thus, the fMWCNT-TiO2/PES hybrid membrane is considered to be a great potential membrane for the improvement of ultrafiltration membranes.
Open AccessRemoval of Humic Acid Using 3-Methacryloxypropyl Trimethoxysilane Functionalized MWCNT Loaded TiO2/PES Hybrid Membrane
In the present work, a highly efficient mixed matrix membrane (MMM) for humic acid (HA) removal was developed. Multiwalled carbon nanotubes (MWCNTs) were functionalized in the presence of 3-methacryloxypropyl trimethoxysilane using the co-condensation method and were subsequently loaded with TiO2 (prepared via the sol–gel route). The as-prepared material was then incorporated into a PES polymer solution to prepare a fMWCNT-TiO2/PES hybrid membrane via non-solvent induced phase inversion. The microstructure of the membrane was characterized using Fourier transform infrared spectroscopy, atomic force microscopy, scanning electron microscopy, water contact angle, thickness, porosity, and pore size. The fMWCNT-TiO2/PES hybrid membrane was tested for the removal of HA and antifouling performance. The results show that the surface hydrophilicity of the membranes was greatly improved upon the addition of the fMWCNT-TiO2 particles. The results show that 92% of HA was effectively removed after 1 h of filtration. In comparison with pristine membrane, the incorporation of fMWCNT-TiO2 nanoparticles led to enhanced pure water flux (99.05 L/m2 h), permeate flux (62.01 L/m2 h), higher HA rejection (92%), and antifouling improvement (RFR: 37.40%, FRR: 86.02%). Thus, the fMWCNT-TiO2/PES hybrid membrane is considered to be a great potential membrane for the improvement of ultrafiltration membranes.
- 14 September 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (8) , 51663
Synthesis of PVDF‐B4C mixed matrix membrane for ultrafiltration of protein and photocatalytic dye removal
In this work, polyvinylidene fluoride‐boron carbide mixed matrix membranes were synthesized via phase inversion method. The synthesized membranes were characterized using field emission scanning electron microscopy, X‐ray diffraction spectroscopy, energy dispersive spectroscopy, porosity, and contact angle. The mixed matrix membranes (0–5 wt.% of boron carbide) were tested for ultrafiltration of bovine serum albumin solution and photodegradation property using rhodamine B and methylene blue dyes. The morphological images reveal the existence of boron carbide particles on the surface of the membranes. Upon introduction of B4C particles, the performance of the membranes was improved: permeate flux increases from 163.13 to 351.15 L/m2 h; bovine serum albumin rejection increased from 77.1% to 99.1%; relative flux reduction decreased from 45.58% to 16.06%; flux recovery ratio increased from 61.71% to 98.42%. Furthermore, maximum photodegradation yield was observed for membranes with 4 wt.% boron carbide particles with degradation efficiency of 96.7% and 96% for rhodamine B and methylene blue dyes, respectively. Furthermore, the rate constant of the optimum membrane was higher than the pristine membrane (about 2.05 and 2.26 times higher for rhodamine B and methylene blue dyes, respectively). Indeed, the mixed matrix membranes present a great prospect for the photodegradation of organic dyes.
- 14 September 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (8) , 51663
Synthesis of PVDF‐B4C mixed matrix membrane for ultrafiltration of protein and photocatalytic dye removal
In this work, polyvinylidene fluoride‐boron carbide mixed matrix membranes were synthesized via phase inversion method. The synthesized membranes were characterized using field emission scanning electron microscopy, X‐ray diffraction spectroscopy, energy dispersive spectroscopy, porosity, and contact angle. The mixed matrix membranes (0–5 wt.% of boron carbide) were tested for ultrafiltration of bovine serum albumin solution and photodegradation property using rhodamine B and methylene blue dyes. The morphological images reveal the existence of boron carbide particles on the surface of the membranes. Upon introduction of B4C particles, the performance of the membranes was improved: permeate flux increases from 163.13 to 351.15 L/m2 h; bovine serum albumin rejection increased from 77.1% to 99.1%; relative flux reduction decreased from 45.58% to 16.06%; flux recovery ratio increased from 61.71% to 98.42%. Furthermore, maximum photodegradation yield was observed for membranes with 4 wt.% boron carbide particles with degradation efficiency of 96.7% and 96% for rhodamine B and methylene blue dyes, respectively. Furthermore, the rate constant of the optimum membrane was higher than the pristine membrane (about 2.05 and 2.26 times higher for rhodamine B and methylene blue dyes, respectively). Indeed, the mixed matrix membranes present a great prospect for the photodegradation of organic dyes.
- Open Access
Characterization and Kinetic Studies of Poly(vinylidene fluoride-co-hexafluoropropylene) Polymer Inclusion Membrane for the Malachite Green Extraction
Textile industry effluent contains a high amount of toxic colorants. These dyes are carcinogenic and threats to the environment and living beings. In this study, poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) was used as the based polymer for PIMs with bis-(2-ethylhexyl) phosphate (B2EHP) and dioctyl phthalate (DOP) as the carrier and plasticizer. The fabricated PIMs were employed to extract the cation dye (Malachite Green; MG) from the feeding phase. PIMs were also characterized by scanning electron microscopy (SEM), atomic force microscope (AFM), contact angle, water uptake, Fourier-transform infrared spectroscopy (FTIR) and ions exchange capacity. The performance of the PIMs was investigated under various conditions such as percentage of carrier and initial dye concentration. With permeability and flux values of 0.1188 cm/min and 1.1913 mg cm/min, PIM produced with 18% w/w PVDF-co-HFP, 21% w/w B2EHP, 1% w/w DOP and 40% w/w THF and was able to achieve more than 97% of MG extraction. The experimental data were then fitted with a pseudo-second-order (PSO) model, and the calculated R2 value was ~0.99. This shows that the data has a good fit with the PSO model. PIM is a potential alternative technology in textile industry effluent treatment; however, the right formulation is crucial for developing a highly efficient membrane.
Open AccessCharacterization and Kinetic Studies of Poly(vinylidene fluoride-co-hexafluoropropylene) Polymer Inclusion Membrane for the Malachite Green Extraction
Textile industry effluent contains a high amount of toxic colorants. These dyes are carcinogenic and threats to the environment and living beings. In this study, poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) was used as the based polymer for PIMs with bis-(2-ethylhexyl) phosphate (B2EHP) and dioctyl phthalate (DOP) as the carrier and plasticizer. The fabricated PIMs were employed to extract the cation dye (Malachite Green; MG) from the feeding phase. PIMs were also characterized by scanning electron microscopy (SEM), atomic force microscope (AFM), contact angle, water uptake, Fourier-transform infrared spectroscopy (FTIR) and ions exchange capacity. The performance of the PIMs was investigated under various conditions such as percentage of carrier and initial dye concentration. With permeability and flux values of 0.1188 cm/min and 1.1913 mg cm/min, PIM produced with 18% w/w PVDF-co-HFP, 21% w/w B2EHP, 1% w/w DOP and 40% w/w THF and was able to achieve more than 97% of MG extraction. The experimental data were then fitted with a pseudo-second-order (PSO) model, and the calculated R2 value was ~0.99. This shows that the data has a good fit with the PSO model. PIM is a potential alternative technology in textile industry effluent treatment; however, the right formulation is crucial for developing a highly efficient membrane.
- Open Access
A Review on Metal Ions Modified TiO2 for Photocatalytic Degradation of Organic Pollutants
TiO2 is a semiconductor material with high chemical stability and low toxicity. It is widely used in the fields of catalysis, sensing, hydrogen production, optics and optoelectronics. However, TiO2 photocatalyst is sensitive to ultraviolet (UV) light; this is why its photocatalytic activity and quantum efficiency are reduced. To enhance the photocatalytic efficiency in the visible light range as well as to increase the number of the active sites on the crystal surface or inhibit the recombination rate of photogenerated electron–hole pairs electrons, various metal ions were used to modify TiO2. This review paper comprehensively summarizes the latest progress on the modification of TiO2 photocatalyst by a variety of metal ions. Lastly, the future prospects of the modification of TiO2 as a photocatalyst are proposed.
Open AccessA Review on Metal Ions Modified TiO2 for Photocatalytic Degradation of Organic Pollutants
TiO2 is a semiconductor material with high chemical stability and low toxicity. It is widely used in the fields of catalysis, sensing, hydrogen production, optics and optoelectronics. However, TiO2 photocatalyst is sensitive to ultraviolet (UV) light; this is why its photocatalytic activity and quantum efficiency are reduced. To enhance the photocatalytic efficiency in the visible light range as well as to increase the number of the active sites on the crystal surface or inhibit the recombination rate of photogenerated electron–hole pairs electrons, various metal ions were used to modify TiO2. This review paper comprehensively summarizes the latest progress on the modification of TiO2 photocatalyst by a variety of metal ions. Lastly, the future prospects of the modification of TiO2 as a photocatalyst are proposed.
- 1 August 2021
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 23
Novel simultaneous anaerobic ammonium and sulfate removal process: A review
- 1 August 2021
- Published by Elsevier in Environmental Technology & Innovation
- Vol. 23
Novel simultaneous anaerobic ammonium and sulfate removal process: A review
- 1 October 2020
- Published by Elsevier in Industrial Crops and Products
- Vol. 154
Preparation and characterization of wood-plastic composite by utilizing a hybrid compatibilizer system
- 1 October 2020
- Published by Elsevier in Industrial Crops and Products
- Vol. 154
Preparation and characterization of wood-plastic composite by utilizing a hybrid compatibilizer system