Douglas Fabris
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Douglas Fabris has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Bruno Henriques
Post-Graduation Program of Dentistry, Center for Education and Research on Dental Implants, Federal University of Santa Catarina, Florianópolis, Brazil
14 shared publications - Marcio Celso Fredel
Ceramic and Composite Materials Research Group (CERMAT), Department of Mechanical Engineering, Federal University of Santa Catarina (UFSC), Florianopolis 88040-900, SC, Brazil
11 shared publications - Filipe Samuel Silva
CMEMS – Center for Microelectromechanical Systems, University of Minho, Guimarães, Portugal
9 shared publications - Júlio C. M. Souza
Center for MicroElectromechanical Systems (CMEMS-UMINHO), University of Minho, Guimarães, Portugal
9 shared publications - Joana Mesquita-Guimaraes
CMEMS-UMinho, University of Minho, Campus de Azurém, 4800-058 Guimarães, Portugal
6 shared publications Bruno Henriques
Ceramic and Composite Materials Research Group (CERMAT) Federal University of Santa Catarina (UFSC) Florianópolis Brazil
5 shared publications
Latest Publications
- 16 February 2025
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (6)
Influence of laser parameters on texturing of 3Y‐TZP and Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 composite
The development of new materials and surface functionalization processes has been extensively studied to further improve the performance of implants. This work explores the direct laser writing method as a potential alternative to produce controlled textures on the surface of traditional 3Y‐TZP and a novel high‐toughness composite (Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 ). A 532 nm picosecond laser source is used to produce lines in sintered samples of both materials with different values of laser fluence, repetition rate, and scanning speed. The resulting textured samples are analyzed using confocal and scanning electron microscopes. Both materials were successfully textured using the laser technique, but the groove morphology and geometry are highly dependent on the parameters used. While low energy results in shallow and irregular grooves, high energy can result in crack and resolidification layer. Overall, for the same set of parameters, the laser produced wider and deeper grooves in the nanocomposite (up to 30 µm wide and 26 µm deep) than in the 3Y‐TZP (up to 12 µm wide and 6 µm deep). Hence, this work showed the feasibility of laser texturing of traditional 3Y‐TZP and the novel Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 that can be further explored to functionalize their surfaces for biomedical applications.
- 16 February 2025
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (6)
Influence of laser parameters on texturing of 3Y‐TZP and Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 composite
The development of new materials and surface functionalization processes has been extensively studied to further improve the performance of implants. This work explores the direct laser writing method as a potential alternative to produce controlled textures on the surface of traditional 3Y‐TZP and a novel high‐toughness composite (Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 ). A 532 nm picosecond laser source is used to produce lines in sintered samples of both materials with different values of laser fluence, repetition rate, and scanning speed. The resulting textured samples are analyzed using confocal and scanning electron microscopes. Both materials were successfully textured using the laser technique, but the groove morphology and geometry are highly dependent on the parameters used. While low energy results in shallow and irregular grooves, high energy can result in crack and resolidification layer. Overall, for the same set of parameters, the laser produced wider and deeper grooves in the nanocomposite (up to 30 µm wide and 26 µm deep) than in the 3Y‐TZP (up to 12 µm wide and 6 µm deep). Hence, this work showed the feasibility of laser texturing of traditional 3Y‐TZP and the novel Ce‐TZP/Al 2 O 3 /SrAl 12 O 19 that can be further explored to functionalize their surfaces for biomedical applications.
- Open Access
- 11 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 19598-19609
Enhancing hydrothermal degradation resistance of (3Y, 12Ce)-TZP composites for biomedical applications: A design perspective
- 11 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 19598-19609
Open AccessEnhancing hydrothermal degradation resistance of (3Y, 12Ce)-TZP composites for biomedical applications: A design perspective
- 18 September 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (49)
Fabrication of Multiscale and Periodically Structured Zirconia Surfaces Using Direct Laser Interference Patterning
The functionalization of zirconia surfaces by accurate and fast printing of periodical patterns embedding sub‐micrometric features is of great interest to many engineering fields and is yet to be explored. This study aims to assess the influence of the Direct Laser Interference Patterning processing parameters on the morphology and microstructure of zirconia surfaces using a 532 nm 10 ps‐pulsed laser source. Well‐defined linear structures with a period of 3 µm are successfully produced. Depending on the laser parameters, the structures are developed at or below the surface level, with higher depths (≈1 µm) being seen for increasing values of laser fluence and pulse overlap. Line‐like hierarchical structures with smaller interference spatial structures (3 µm period) and higher secondary structures with different periods (18, 15, and 12 µm) and heights (7, 5, and 3 µm, respectively) are also obtained on zirconia surface. Ablated regions presented few traces of molten material, nano‐droplets, and sub‐micrometric (<1 µm) pores, while no (sub) micrometric cracks are detected. A slight amount of tetragonal to monoclinic phase transformation (≈5%) is detected by X‐ray diffractometry. A processability map for ps‐laser processing of zirconia is proposed based on the experimental data.
- 18 September 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (49)
Fabrication of Multiscale and Periodically Structured Zirconia Surfaces Using Direct Laser Interference Patterning
The functionalization of zirconia surfaces by accurate and fast printing of periodical patterns embedding sub‐micrometric features is of great interest to many engineering fields and is yet to be explored. This study aims to assess the influence of the Direct Laser Interference Patterning processing parameters on the morphology and microstructure of zirconia surfaces using a 532 nm 10 ps‐pulsed laser source. Well‐defined linear structures with a period of 3 µm are successfully produced. Depending on the laser parameters, the structures are developed at or below the surface level, with higher depths (≈1 µm) being seen for increasing values of laser fluence and pulse overlap. Line‐like hierarchical structures with smaller interference spatial structures (3 µm period) and higher secondary structures with different periods (18, 15, and 12 µm) and heights (7, 5, and 3 µm, respectively) are also obtained on zirconia surface. Ablated regions presented few traces of molten material, nano‐droplets, and sub‐micrometric (<1 µm) pores, while no (sub) micrometric cracks are detected. A slight amount of tetragonal to monoclinic phase transformation (≈5%) is detected by X‐ray diffractometry. A processability map for ps‐laser processing of zirconia is proposed based on the experimental data.
- Open Access
- 30 September 2023
- Published by Elsevier in Open Ceramics
- Vol. 16, 100475
Tridimensional characterization of open cells and hollow strut cavities from SiC and ZrO2 foams: A study accomplished with open-source software tools
- 30 September 2023
- Published by Elsevier in Open Ceramics
- Vol. 16, 100475
Open AccessTridimensional characterization of open cells and hollow strut cavities from SiC and ZrO2 foams: A study accomplished with open-source software tools
- 25 September 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (2)
Direct Laser Interference Patterning of Zirconia Using Infra‐Red Picosecond Pulsed Laser: Effect of Laser Processing Parameters on the Surface Topography and Microstructure
This study investigates the influence of processing parameters when applying direct laser interference patterning (DLIP) on the morphology and microstructure of zirconia surfaces using a 10 ps‐pulsed laser source with 1064 nm wavelength. An experimental testing matrix is built with different values of laser fluence (5.7–18.2 J cm−2) and pulse overlap (66–98%). Surface morphology and microstructure are characterized by confocal microscopy and scanning electron microscopy. Homogeneous line‐like patterns with periodic spatial repetition of 5.0 µm, with varying depths, widths, and aspect ratio, are fabricated using proper processing parameters (5.7–7.6 J cm−2 and 92–96%). Structures with maximum depth of 1.5 µm and sharp edges are obtained (7.6 J cm−2 and 96% overlap). Ablated regions presented a morphology typical of photophysical ablation mechanism, with signs of molten material at the surface. Sub‐micrometric pores and nanodroplets are registered for all conditions, while sub‐micrometric cracks developed only for higher fluences. A processing window conducing to homogenous DLIP structures is set based on experimental data. Periodic structures with multiscale topographic features are successfully obtained on zirconia surfaces using DLIP technology in this study. These outcomes open new perspectives for fabrication of multifunctional zirconia surfaces for advanced biomedical and engineering applications.
- 25 September 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (2)
Direct Laser Interference Patterning of Zirconia Using Infra‐Red Picosecond Pulsed Laser: Effect of Laser Processing Parameters on the Surface Topography and Microstructure
This study investigates the influence of processing parameters when applying direct laser interference patterning (DLIP) on the morphology and microstructure of zirconia surfaces using a 10 ps‐pulsed laser source with 1064 nm wavelength. An experimental testing matrix is built with different values of laser fluence (5.7–18.2 J cm−2) and pulse overlap (66–98%). Surface morphology and microstructure are characterized by confocal microscopy and scanning electron microscopy. Homogeneous line‐like patterns with periodic spatial repetition of 5.0 µm, with varying depths, widths, and aspect ratio, are fabricated using proper processing parameters (5.7–7.6 J cm−2 and 92–96%). Structures with maximum depth of 1.5 µm and sharp edges are obtained (7.6 J cm−2 and 96% overlap). Ablated regions presented a morphology typical of photophysical ablation mechanism, with signs of molten material at the surface. Sub‐micrometric pores and nanodroplets are registered for all conditions, while sub‐micrometric cracks developed only for higher fluences. A processing window conducing to homogenous DLIP structures is set based on experimental data. Periodic structures with multiscale topographic features are successfully obtained on zirconia surfaces using DLIP technology in this study. These outcomes open new perspectives for fabrication of multifunctional zirconia surfaces for advanced biomedical and engineering applications.
- Open Access
- 8 August 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (12) , 7189-7193
Fabrication of functional zirconia surfaces using a two‐beam interference setup employing a picosecond laser system with 532‐nm wavelength: Morphology, microstructure, and wettability
The aim of this work was to evaluate the feasibility of the fabrication of microtextures in zirconia using the direct laser interference patterning (DLIP) technique. A green ultra‐short pulsed laser (532 nm, 10 ps) with a two‐beam interference setup was used to produce line‐like structures with a spatial period of 3 µm. For a fixed set of fluence and pulse‐to‐pulse overlap values (6.2 J/cm2, 81%), periodic structures were successfully created for different hatch distances. The average depth of the features ranged from 0.37 µm for a hatch distance of 14.4 µm up to 0.84 µm for a hatch distance of 12.4 µm. However, a further decrease in hatch distance did not result in an increase in depth since the region of the ridges is also ablated. Scanning electron microscopy analysis showed pores formation on the laser grooves, but no sign of micro‐cracking could be observed. Wettability tests showed an increase in hydrophobicity after DLIP. These results bring exciting perspectives on the fabrication of micro‐textures with DLIP on zirconia surface.
- 8 August 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (12) , 7189-7193
Open AccessFabrication of functional zirconia surfaces using a two‐beam interference setup employing a picosecond laser system with 532‐nm wavelength: Morphology, microstructure, and wettability
The aim of this work was to evaluate the feasibility of the fabrication of microtextures in zirconia using the direct laser interference patterning (DLIP) technique. A green ultra‐short pulsed laser (532 nm, 10 ps) with a two‐beam interference setup was used to produce line‐like structures with a spatial period of 3 µm. For a fixed set of fluence and pulse‐to‐pulse overlap values (6.2 J/cm2, 81%), periodic structures were successfully created for different hatch distances. The average depth of the features ranged from 0.37 µm for a hatch distance of 14.4 µm up to 0.84 µm for a hatch distance of 12.4 µm. However, a further decrease in hatch distance did not result in an increase in depth since the region of the ridges is also ablated. Scanning electron microscopy analysis showed pores formation on the laser grooves, but no sign of micro‐cracking could be observed. Wettability tests showed an increase in hydrophobicity after DLIP. These results bring exciting perspectives on the fabrication of micro‐textures with DLIP on zirconia surface.
- Open Access
- 18 July 2023
- Published by Elsevier in Dental Materials
- Vol. 39 (9) , 807-819
Translucent multi-layered zirconia: Sandblasting effect on optical and mechanical properties
- 18 July 2023
- Published by Elsevier in Dental Materials
- Vol. 39 (9) , 807-819
Open AccessTranslucent multi-layered zirconia: Sandblasting effect on optical and mechanical properties
- Open Access
Multi-Scale Structuring of CoCrMo and AZ91D Magnesium Alloys Using Direct Laser Interference Patterning
In this work, the technique of Direct Laser Interference Patterning (DLIP) was used to fabricate micrometric structures at the surface of Cobalt-Chromium-Molybdenum and AZ91D magnesium alloys. Line-like patterns with spatial periods of 5 μm were textured using an ultra-short pulsed laser (10 ps pulse duration and 1064 nm wavelength) with a two-beam interference setup. The surface topography, morphology, and chemical modifications were analysed using Confocal Microscopy, Scanning Electron Microscopy, and Energy Dispersive Spectroscopy (EDS), respectively. Laser fluence and pulse overlap were varied to evaluate their influence on the final structure. Homogeneous structures were achieved for the CoCrMo alloy for every condition tested, with deeper structures (up to 0.85 μm) being achieved for higher energy levels (higher overlap and/or fluence). For high energy, sub-micrometric secondary structures, so-called LIPSS, could also be observed on the CoCrMo. The EDS analysis showed some oxidation after the laser texturing. Regarding the AZ91D alloy, deeper structures could be achieved (up to 2.5 μm), but more melting and oxidation was observed, forming spherical oxide particles. Nonetheless, these results bring new perspectives on the fabrication of microtextures on the surface of CoCrMo and AZ91D using DLIP.
Open AccessMulti-Scale Structuring of CoCrMo and AZ91D Magnesium Alloys Using Direct Laser Interference Patterning
In this work, the technique of Direct Laser Interference Patterning (DLIP) was used to fabricate micrometric structures at the surface of Cobalt-Chromium-Molybdenum and AZ91D magnesium alloys. Line-like patterns with spatial periods of 5 μm were textured using an ultra-short pulsed laser (10 ps pulse duration and 1064 nm wavelength) with a two-beam interference setup. The surface topography, morphology, and chemical modifications were analysed using Confocal Microscopy, Scanning Electron Microscopy, and Energy Dispersive Spectroscopy (EDS), respectively. Laser fluence and pulse overlap were varied to evaluate their influence on the final structure. Homogeneous structures were achieved for the CoCrMo alloy for every condition tested, with deeper structures (up to 0.85 μm) being achieved for higher energy levels (higher overlap and/or fluence). For high energy, sub-micrometric secondary structures, so-called LIPSS, could also be observed on the CoCrMo. The EDS analysis showed some oxidation after the laser texturing. Regarding the AZ91D alloy, deeper structures could be achieved (up to 2.5 μm), but more melting and oxidation was observed, forming spherical oxide particles. Nonetheless, these results bring new perspectives on the fabrication of microtextures on the surface of CoCrMo and AZ91D using DLIP.
- 21 February 2023
- Published by Elsevier in Materials Letters
- Vol. 339
Multi-scale textured PEEK surfaces obtained by direct laser interference patterning using IR ultra-short pulses
- 21 February 2023
- Published by Elsevier in Materials Letters
- Vol. 339
Multi-scale textured PEEK surfaces obtained by direct laser interference patterning using IR ultra-short pulses
- 16 September 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (1) , 2100624
Influence of the Addition of Ni‐Coated Carbon Nanotubes on the Mechanical Properties of Highly Porous Zirconia Cellular Structures
Herein, the effect of the addition of Ni‐coated carbon nanotubes (CNTs) on the microstructure, mechanical properties, and morphology of zirconia porous cellular structures is studied, aiming to increase their mechanical strength. Highly porous structures of monolithic zirconia (ZrO2) and zirconia reinforced with Ni‐doped CNTs (ZrO2 + CNT/Ni) are fabricated through the replica method. Scanning electron microscopy and micro‐computed tomography (microCT) analyses show that ZrO2 + CNT/Ni specimens present lower overall porosity (88.0%) than monolithic ZrO2 (93.8%), indicating improved sintering kinetics. Compressive tests for the ZrO2 + CNT/Ni samples result in a compressive strength of 0.82 ± 0.10 MPa, a threefold value of that of the monolithic sample (0.25 ± 0.07 MPa). The ZrO2 + CNT/Ni samples also present a higher elastic modulus (41.02 ± 4.94 MPa) than the ZrO2 ones (21.92 ± 5.40 MPa). Thus, the addition of Ni‐coated CNTs significantly improves the strength of highly porous zirconia cellular structures.
- 16 September 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (1) , 2100624
Influence of the Addition of Ni‐Coated Carbon Nanotubes on the Mechanical Properties of Highly Porous Zirconia Cellular Structures
Herein, the effect of the addition of Ni‐coated carbon nanotubes (CNTs) on the microstructure, mechanical properties, and morphology of zirconia porous cellular structures is studied, aiming to increase their mechanical strength. Highly porous structures of monolithic zirconia (ZrO2) and zirconia reinforced with Ni‐doped CNTs (ZrO2 + CNT/Ni) are fabricated through the replica method. Scanning electron microscopy and micro‐computed tomography (microCT) analyses show that ZrO2 + CNT/Ni specimens present lower overall porosity (88.0%) than monolithic ZrO2 (93.8%), indicating improved sintering kinetics. Compressive tests for the ZrO2 + CNT/Ni samples result in a compressive strength of 0.82 ± 0.10 MPa, a threefold value of that of the monolithic sample (0.25 ± 0.07 MPa). The ZrO2 + CNT/Ni samples also present a higher elastic modulus (41.02 ± 4.94 MPa) than the ZrO2 ones (21.92 ± 5.40 MPa). Thus, the addition of Ni‐coated CNTs significantly improves the strength of highly porous zirconia cellular structures.