MFMauricio Fernández

Mauricio Fernández

*This is an algorithmically generated author record based on publicly available information.

Mauricio Fernández has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Materials in the Drive Chain – Modeling Materials for the Internet of Production

    by Ali Rajaei, Marco Becker, Yuanbin Deng, Oliver Schenk, Soheil Rooein, Patricia de Oliveira Löhrer, Niklas Reinisch, Tarik Viehmann, Mustapha Abouridouane, Mauricio Fernández, et al.

    In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.

  • Open Access

    Materials in the Drive Chain – Modeling Materials for the Internet of Production

    by Ali Rajaei, Marco Becker, Yuanbin Deng, Oliver Schenk, Soheil Rooein, Patricia de Oliveira Löhrer, Niklas Reinisch, Tarik Viehmann, Mustapha Abouridouane, Mauricio Fernández, et al.

    In this chapter, the focus lies on a predictive description of the material response to the thermomechanical loads within different process steps by means of physical and data-driven models. The modeling approaches are demonstrated in examples of innovative production technologies for components of a drive chain: Fine blanking of parts; powder metallurgical (PM) production of gears; open-die forging and machining of drive shafts. In fine blanking, material, process, and quality data are acquired to model interactions between process and material with data-driven methods. Interpretable machine learning is utilized to non-destructively characterize the initial material state, enabling an optimization of process parameters for a given material state in the long-term. The PM process chain of the gear includes sintering, pressing, surface densification, case hardening, and finishing by grinding. Several modeling and characterization approaches are applied to quantitatively describe the microstructure evolutions in terms of porosity during sintering, density profile after cold rolling, hardness and residual stresses after heat treating and grinding and the tooth root load bearing capacity. In the example of the open-die forging, a knowledge-based approach is developed to support the decision-making process regarding the choice of the proper material and optimized pass schedules. Considering the microstructure of the forged shaft, the elastoplastic material behavior is described by a dislocation-based, multiscale modeling approach. On this basis, process simulations could be carried out to predict the process forces, chip form, residual stresses, and the tool life among other output data.


  • Open Access

    Nonlinear multiscale simulation of elastic beam lattices with anisotropic homogenized constitutive models based on artificial neural networks

    by Til Gärtner, Mauricio Fernández, Oliver Weeger

    A sequential nonlinear multiscale method for the simulation of elastic metamaterials subject to large deformations and instabilities is proposed. For the finite strain homogenization of cubic beam lattice unit cells, a stochastic perturbation approach is applied to induce buckling. Then, three variants of anisotropic effective constitutive models built upon artificial neural networks are trained on the homogenization data and investigated: one is hyperelastic and fulfills the material symmetry conditions by construction, while the other two are hyperelastic and elastic, respectively, and approximate the material symmetry through data augmentation based on strain energy densities and stresses. Finally, macroscopic nonlinear finite element simulations are conducted and compared to fully resolved simulations of a lattice structure. The good agreement between both approaches in tension and compression scenarios shows that the sequential multiscale approach based on anisotropic constitutive models can accurately reproduce the highly nonlinear behavior of buckling-driven 3D metamaterials at lesser computational effort.


  • Open Access

    Anisotropic hyperelastic constitutive models for finite deformations combining material theory and data-driven approaches with application to cubic lattice metamaterials

    by Mauricio Fernández, Mostafa Jamshidian, Thomas Böhlke, Kristian Kersting, Oliver Weeger

    This work investigates the capabilities of anisotropic theory-based, purely data-driven and hybrid approaches to model the homogenized constitutive behavior of cubic lattice metamaterials exhibiting large deformations and buckling phenomena. The effective material behavior is assumed as hyperelastic, anisotropic and finite deformations are considered. A highly flexible analytical approach proposed by Itskov (Int J Numer Methods Eng 50(8): 1777–1799, 2001) is taken into account, which ensures material objectivity and fulfillment of the material symmetry group conditions. Then, two non-intrusive data-driven approaches are proposed, which are built upon artificial neural networks and formulated such that they also fulfill the objectivity and material symmetry conditions. Finally, a hybrid approach combing the approach of Itskov (Int J Numer Methods Eng 50(8): 1777–1799, 2001) with artificial neural networks is formulated. Here, all four models are calibrated with simulation data of the homogenization of two cubic lattice metamaterials at finite deformations. The data-driven models are able to reproduce the calibration data very well and reproduce the manifestation of lattice instabilities. Furthermore, they achieve superior accuracy over the analytical model also in additional test scenarios. The introduced hyperelastic models are formulated as general as possible, such that they can not only be used for lattice structures, but for any anisotropic hyperelastic material. Further, access to the complete simulation data is provided through the public repository https://github.com/CPShub/sim-data.


  • On the generation of periodic discrete structures with identical two-point correlation

    by M. Fernández, F. Fritzen

    Strategies for the generation of periodic discrete structures with identical two-point correlation—called 2PC-equivalent—are developed. It is shown that starting from a set of 2PC-equivalent root structures, 2PC-equivalent child structures of arbitrary resolution and number of phases (e.g. material phases) can be generated based on phase extension through trivial embeddings, kernel-based extension and phase coalescence. Proofs are provided by means of discrete Fourier transform theory. A Python 3 implementation is offered for reproduction of examples and future applications.


  • Open Access

    Construction of a Class of Sharp Löwner Majorants for a Set of Symmetric Matrices

    by Mauricio Fernández, Felix Fritzen

    The Löwner partial order is taken into consideration in order to define Löwner majorants for a given finite set of symmetric matrices. A special class of Löwner majorants is analyzed based on two specific matrix parametrizations: a two-parametric form and a four-parametric form, which arise in the context of so-called zeroth-order bounds of the effective linear behavior in the field of solid mechanics in engineering. The condensed explicit conditions defining the convex parameter sets of Löwner majorants are derived. Examples are provided, and potential application to semidefinite programming problems is discussed. Open-source MATLAB software is provided to support the theoretical findings and for reproduction of the presented results. The results of the present work offer in combination with the theory of zeroth-order bounds of mechanics a highly efficient approach for the automated material selection for future engineering applications.

  • Open Access

    On the generation of periodic discrete structures with identical two-point correlation

    by Mauricio Fernández, Felix Fritzen

    Strategies for the generation of periodic discrete structures with identical two-point correlation are developed. Starting from a pair of root structures, which are not related by translation, phase inversion or axis reflections, child structures of arbitrary resolution (i.e., pixel or voxel numbers) and number of phases (i.e., material phases/species) can be generated by means of trivial embedding based phase extension, application of kernels and/or phase coalescence, such that the generated structures inherit the two-point-correlation equivalence. Proofs of the inheritance property are provided by means of the Discrete Fourier Transform theory. A Python 3 implementation of the results is offered by the authors through the Github repository https://github.com/DataAnalyticsEngineering/EQ2PC in order to make the provided results reproducible and useful for all interested readers. Examples for the generation of structures are demonstrated, together with applications in the homogenization theory of periodic media.

  • Open Access

    Application of artificial neural networks for the prediction of interface mechanics: a study on grain boundary constitutive behavior

    by Mauricio Fernández, Shahed Rezaei, Jaber Rezaei Mianroodi, Felix Fritzen, Stefanie Reese

    The present work aims at the identification of the effective constitutive behavior of $$\Sigma 5$$Σ5 aluminum grain boundaries (GB) for proportional loading by using machine learning (ML) techniques. The input for the ML approach is high accuracy data gathered in challenging molecular dynamics (MD) simulations at the atomic scale for varying temperatures and loading conditions. The effective traction-separation relation is recorded during the MD simulations. The raw MD data then serves for the training of an artificial neural network (ANN) as a surrogate model of the constitutive behavior at the grain boundary. Despite the extremely fluctuating nature of the MD data and its inhomogeneous distribution in the traction-separation space, the ANN surrogate trained on the raw MD data shows a very good agreement in the average behavior without any data-smoothing or pre-processing. Further, it is shown that the trained traction-separation ANN captures important physical properties and is able to predict traction values for given separations not contained in the training data. For example, MD simulations show a transition in traction-separation behaviour from pure sliding mode under shear load to combined GB sliding and decohesion with intermediate hardening regime at mixed load directions. These changes in GB behaviour are fully captured in the ANN predictions. Furthermore, by construction, the ANN surrogate is differentiable for arbitrary separation and also temperature, such that a thermo-mechanical tangent stiffness operator can always be evaluated. The trained ANN can then serve for large-scale FE simulation as an alternative to direct MD-FE coupling which is often infeasible in practical applications.