Bai Nguyen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Bai Nguyen has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Deukhyoun Heo
School of Electrical Engineering and Computer Science, Washington State University, Pullman, WA, USA
7 shared publications Zhiyuan Zhou
School of Electrical Engineering and Computer Science, Washington State University, Pullman, WA, USA
7 shared publications- Wookpyo Hong
Department of Electrical Engineering and Computer Science, Washington State University, Pullman, WA 99164 USA
5 shared publications - Nghia Tang
School of Electrical Engineering and Computer Science, Washington State University, Pullman, WA, USA
4 shared publications Nghia Tang
Department of Electrical Engineering and Computer Science, Washington State University, Pullman, USA
3 shared publications- Partha Pratim Pande
Washington State University
3 shared publications
Latest Publications
- 29 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (12) , 4823-4836
An Inductor-First Single-Inductor Multiple-Output Hybrid DC–DC Converter With Integrated Flying Capacitor for SoC Applications
With the increasing complexity of highly integrated system on chips (SoCs), the power management system (PMS) is required to provide several power supplies efficiently for individual blocks. This paper presents a single-inductor multiple-output (SIMO) inductor-first hybrid converter that generates three outputs between 0.4V and 1.6V from a 1.8V input. The proposed multiple-output hybrid power stage can improve the conversion efficiency by reducing inductor current while extending the output voltage range compared with the existing hybrid topologies. In addition, the proposed converter employs an on-chip switched-capacitor power stage (SCPS) with a dual-switching frequency technique, resulting in a fast response time, low cross-regulation, and reduced number of on-chip pads. Measurement results show that the converter achieves a peak efficiency of 87.5% with the maximum output current of 450mA. The converter is integrated with a fast voltage regulation loop with 500MHz system clock to achieve a less than 0.01mA/mV cross-regulation and a maximum 20mV overshoot at full-load transient response. The design is fabricated in the standard 180nm CMOS technology.
- 29 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (12) , 4823-4836
An Inductor-First Single-Inductor Multiple-Output Hybrid DC–DC Converter With Integrated Flying Capacitor for SoC Applications
With the increasing complexity of highly integrated system on chips (SoCs), the power management system (PMS) is required to provide several power supplies efficiently for individual blocks. This paper presents a single-inductor multiple-output (SIMO) inductor-first hybrid converter that generates three outputs between 0.4V and 1.6V from a 1.8V input. The proposed multiple-output hybrid power stage can improve the conversion efficiency by reducing inductor current while extending the output voltage range compared with the existing hybrid topologies. In addition, the proposed converter employs an on-chip switched-capacitor power stage (SCPS) with a dual-switching frequency technique, resulting in a fast response time, low cross-regulation, and reduced number of on-chip pads. Measurement results show that the converter achieves a peak efficiency of 87.5% with the maximum output current of 450mA. The converter is integrated with a fast voltage regulation loop with 500MHz system clock to achieve a less than 0.01mA/mV cross-regulation and a maximum 20mV overshoot at full-load transient response. The design is fabricated in the standard 180nm CMOS technology.
- 19 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (6) , 1805-1815
Fully Integrated Switched-Inductor-Capacitor Voltage Regulator With 0.82-A/mm2 Peak Current Density and 78% Peak Power Efficiency
Fully integrated voltage regulators (FIVRs) can improve the performance and reduce the power consumption of a system-on-chip (SoC) by providing point-of-load voltage regulation with dynamic voltage scaling. The desirable attributes of FIVRs include high power efficiency, high power density, and fast transient response, which are difficult to achieve due to on-chip area constraint and parasitic effects. Low-quality and low-density on-chip inductors and capacitors are currently the main performance-limiting factors. This article presents a switched-inductor-capacitor (SIC) voltage converter that can operate more efficiently with compact on-chip air-cored metal-tracked inductors than existing step-down voltage converters. The SIC converter consists of an inductor, a flying capacitor, and three power switches, and it can provide fine-grained voltage regulation by using pulsewidth-modulation (PWM) control. The unique SIC converter topology eases the on-chip inductor integration by positioning the inductor at the input power supply and reducing the current stress of the inductor. A proof-of-concept fully integrated SIC voltage regulator is fabricated in a 65-nm CMOS process, with an area of 1.3 mm x 0.5 mm excluding pads. The output voltage can be regulated from 0.6 to 0.9 V given a 1.2-V input power supply. The output voltage ripple is below 56 mV over the entire range of output voltages and load currents. The peak power efficiency is 78% at an output of 0.9 V and 406 mA. The peak power density is 730 mW/mm², and the peak current density is 820 mA/mm².
- 19 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (6) , 1805-1815
Fully Integrated Switched-Inductor-Capacitor Voltage Regulator With 0.82-A/mm2 Peak Current Density and 78% Peak Power Efficiency
Fully integrated voltage regulators (FIVRs) can improve the performance and reduce the power consumption of a system-on-chip (SoC) by providing point-of-load voltage regulation with dynamic voltage scaling. The desirable attributes of FIVRs include high power efficiency, high power density, and fast transient response, which are difficult to achieve due to on-chip area constraint and parasitic effects. Low-quality and low-density on-chip inductors and capacitors are currently the main performance-limiting factors. This article presents a switched-inductor-capacitor (SIC) voltage converter that can operate more efficiently with compact on-chip air-cored metal-tracked inductors than existing step-down voltage converters. The SIC converter consists of an inductor, a flying capacitor, and three power switches, and it can provide fine-grained voltage regulation by using pulsewidth-modulation (PWM) control. The unique SIC converter topology eases the on-chip inductor integration by positioning the inductor at the input power supply and reducing the current stress of the inductor. A proof-of-concept fully integrated SIC voltage regulator is fabricated in a 65-nm CMOS process, with an area of 1.3 mm x 0.5 mm excluding pads. The output voltage can be regulated from 0.6 to 0.9 V given a 1.2-V input power supply. The output voltage ripple is below 56 mV over the entire range of output voltages and load currents. The peak power efficiency is 78% at an output of 0.9 V and 406 mA. The peak power density is 730 mW/mm², and the peak current density is 820 mA/mm².
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (9) , 3234-3247
Analysis and Design Method of Multiple-Output Switched-Capacitor Voltage Regulators With a Reduced Number of Power Electronic Components
This paper presents a study of compact multiple-output switched-capacitor voltage regulators (MOSCVRs). Two methods to produce multiple outputs with an SCVR and their effects on performance - power efficiency and cross-regulation, are examined with output impedance analysis. Moreover, to help a circuit designer to implement a compact MOSCVR, a design method to determine the number of outputs and their conversion ratios is also proposed in this work. To verify this method, we demonstrate the design of an example compact MOSCVR. The MOSCVR is capable of simultaneously producing four different output voltages from a single input power supply with only two flying capacitors and twelve switches. The study presented in this work provides not only comprehensive insight but also guidance to find the suitable topology of a compact MOSCVR.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (9) , 3234-3247
Analysis and Design Method of Multiple-Output Switched-Capacitor Voltage Regulators With a Reduced Number of Power Electronic Components
This paper presents a study of compact multiple-output switched-capacitor voltage regulators (MOSCVRs). Two methods to produce multiple outputs with an SCVR and their effects on performance - power efficiency and cross-regulation, are examined with output impedance analysis. Moreover, to help a circuit designer to implement a compact MOSCVR, a design method to determine the number of outputs and their conversion ratios is also proposed in this work. To verify this method, we demonstrate the design of an example compact MOSCVR. The MOSCVR is capable of simultaneously producing four different output voltages from a single input power supply with only two flying capacitors and twelve switches. The study presented in this work provides not only comprehensive insight but also guidance to find the suitable topology of a compact MOSCVR.
- 12 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (2) , 622-633
Clock-Voltage Co-Regulator With Adaptive Power Budget Tracking for Robust Near-Threshold-Voltage Sequential Logic Circuits
This paper presents a post-regulation power management integrated circuit for energy harvesting applications. It incorporates a power budget tracking mechanism to adaptively control the power consumption of a near-threshold-voltage microcontroller based on the time-varying available input power. In addition, the proposed integrated circuit adapts the clock frequency of the microcontroller to the supply voltage under the time-varying input available power to prevent timing violations for the sequential logics of the microcontroller. A prototype shows the adaptive power budget tracking can correct timing violations with only 6.26uA quiescent current. It also properly operates sequential logic circuits at as low as 188mV supply voltage and 1.61MHz clock without interruption when powered by a solar energy harvester under the light illuminance range of 1000-6000lx. This adaptive power tracking structure enables the near-threshold-voltage microcontroller to maintain a continuous operation at optimized processing speed under the varying power condition without violating the timing requirements.
- 12 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (2) , 622-633
Clock-Voltage Co-Regulator With Adaptive Power Budget Tracking for Robust Near-Threshold-Voltage Sequential Logic Circuits
This paper presents a post-regulation power management integrated circuit for energy harvesting applications. It incorporates a power budget tracking mechanism to adaptively control the power consumption of a near-threshold-voltage microcontroller based on the time-varying available input power. In addition, the proposed integrated circuit adapts the clock frequency of the microcontroller to the supply voltage under the time-varying input available power to prevent timing violations for the sequential logics of the microcontroller. A prototype shows the adaptive power budget tracking can correct timing violations with only 6.26uA quiescent current. It also properly operates sequential logic circuits at as low as 188mV supply voltage and 1.61MHz clock without interruption when powered by a solar energy harvester under the light illuminance range of 1000-6000lx. This adaptive power tracking structure enables the near-threshold-voltage microcontroller to maintain a continuous operation at optimized processing speed under the varying power condition without violating the timing requirements.
- 14 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (12) , 2861-2871
A Dual-Output Step-Down Switched-Capacitor Voltage Regulator With a Flying Capacitor Crossing Technique for Enhanced Power Efficiency
This paper presents a dual-output switched-capacitor voltage regulator (DOSCVR) with a new flying capacitor crossing technique (FCCT) to improve power efficiency. With the FCCT, the power loss of the DOSCVR is reduced by 28%, increasing the power efficiency by 7% compared with the power efficiency of the conventional method that generates two voltages using independent single-output SCVRs. This enhanced efficiency results in no area penalty since the total flying capacitance remains unchanged. A prototype is then implemented in a 0.13-μm CMOS process to validate the proposed scheme. The prototype simultaneously produces two regulated voltages of 0.44 and 0.88 V from an input voltage of 1.5 V. The output voltages are regulated by low-bound regulation with frequency modulation. The maximum output current is 12 mA with a total flying capacitance of 0.98 nF, and the measured peak efficiency is 78%.
- 14 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (12) , 2861-2871
A Dual-Output Step-Down Switched-Capacitor Voltage Regulator With a Flying Capacitor Crossing Technique for Enhanced Power Efficiency
This paper presents a dual-output switched-capacitor voltage regulator (DOSCVR) with a new flying capacitor crossing technique (FCCT) to improve power efficiency. With the FCCT, the power loss of the DOSCVR is reduced by 28%, increasing the power efficiency by 7% compared with the power efficiency of the conventional method that generates two voltages using independent single-output SCVRs. This enhanced efficiency results in no area penalty since the total flying capacitance remains unchanged. A prototype is then implemented in a 0.13-μm CMOS process to validate the proposed scheme. The prototype simultaneously produces two regulated voltages of 0.44 and 0.88 V from an input voltage of 1.5 V. The output voltages are regulated by low-bound regulation with frequency modulation. The maximum output current is 12 mA with a total flying capacitance of 0.98 nF, and the measured peak efficiency is 78%.
- 20 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (2) , 1721-1731
A 12- or 48-V Input, 0.9-V Output Active-Clamp Forward Converter Power Block for Servers and Datacenters
DC-to-DC power supplies are critical components for processors in high performance computing and datacenter servers. Conversion from an intermediate bus voltage (e.g., 12 or 48 V) to the core voltage (∼0.9 V) of processors must be efficient, compact, and cost effective. This paper proposes two versions of active-clamp forward converter (ACFC) power blocks to supply core voltage from either 12 or 48 V intermediate bus voltage. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to fit in a standard 1U server. A low loss, compact planar transformer is designed into the ACFC power block printed circuit board (PCB). A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the dc loss in the current path. Thorough analysis is performed to model the conversion loss of the proposed power block. Experimental results show a peak efficiency of 90.4% (12 V input) and 89.5% (48 V input) with 0.9-V output.
- 20 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (2) , 1721-1731
A 12- or 48-V Input, 0.9-V Output Active-Clamp Forward Converter Power Block for Servers and Datacenters
DC-to-DC power supplies are critical components for processors in high performance computing and datacenter servers. Conversion from an intermediate bus voltage (e.g., 12 or 48 V) to the core voltage (∼0.9 V) of processors must be efficient, compact, and cost effective. This paper proposes two versions of active-clamp forward converter (ACFC) power blocks to supply core voltage from either 12 or 48 V intermediate bus voltage. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to fit in a standard 1U server. A low loss, compact planar transformer is designed into the ACFC power block printed circuit board (PCB). A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the dc loss in the current path. Thorough analysis is performed to model the conversion loss of the proposed power block. Experimental results show a peak efficiency of 90.4% (12 V input) and 89.5% (48 V input) with 0.9-V output.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (3) , 1799-1808
Analog-Assisted Digital Capacitorless Low-Dropout Regulator Supporting Wide Load Range
Capacitorless (CL) low-dropout regulators (LDO) have gained significant research interest for point-of-load voltage regulation without off-chip capacitors. While analog CL-LDOs can deliver superior power supply rejection (PSR), digital CL-LDOs are more scalable and efficient. To achieve the advantages of both types, this paper presents a digital CL-LDO with an analog PSR enhancer, delivering strong PSR without compromising scalability and efficiency. Load regulation is performed by an asynchronous digital feedback controller for fast transient response and scalable load drivability. PSR is achieved by a load-insensitive wide-bandwidth analog controller. A prototype chip of the analog-assisted digital CL-LDO is fabricated in a 130-nm CMOS process with an active area of 0.0645 mm 2 , supporting load current up to 50 mA at nominal 1-V input and 0.8-V output. The measured PSR is better than -20 dB for frequencies up to 10 MHz, and the measured current efficiency peaks at 99.3%, with average current efficiency of 96.7% across 50× load range. The measured transient response to a full load step, with two values of load capacitance (100 pF and 10 nF), demonstrates the LDO's stable operation over a wide range of load resistance and capacitance.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (3) , 1799-1808
Analog-Assisted Digital Capacitorless Low-Dropout Regulator Supporting Wide Load Range
Capacitorless (CL) low-dropout regulators (LDO) have gained significant research interest for point-of-load voltage regulation without off-chip capacitors. While analog CL-LDOs can deliver superior power supply rejection (PSR), digital CL-LDOs are more scalable and efficient. To achieve the advantages of both types, this paper presents a digital CL-LDO with an analog PSR enhancer, delivering strong PSR without compromising scalability and efficiency. Load regulation is performed by an asynchronous digital feedback controller for fast transient response and scalable load drivability. PSR is achieved by a load-insensitive wide-bandwidth analog controller. A prototype chip of the analog-assisted digital CL-LDO is fabricated in a 130-nm CMOS process with an active area of 0.0645 mm 2 , supporting load current up to 50 mA at nominal 1-V input and 0.8-V output. The measured PSR is better than -20 dB for frequencies up to 10 MHz, and the measured current efficiency peaks at 99.3%, with average current efficiency of 96.7% across 50× load range. The measured transient response to a full load step, with two values of load capacitance (100 pF and 10 nF), demonstrates the LDO's stable operation over a wide range of load resistance and capacitance.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 287-291
Analytic model for power MOSFET turn-off switching loss under the effect of significant current diversion at fast switching events
The conventional method to evaluate switching loss of power MOSFETs is commonly based on the existence of the plateau gate-voltage region in the gate-charge plot. However, a very different behavior of the MOSFET with disappearance of the plateau region is observed under significant current diversion between channel and parasitic capacitances when a large gate drive current is applied to turn off the MOSFET. As the modern power converter is pursuing higher switching frequency, the gate drive current becomes larger accordingly to turn on and off the power MOSFET faster. Hence, this paper proposes an analytical model to predict the timing pattern and the switching loss more precisely in such conditions. Simulation and measurement have been conducted to validate this model, showing an accurate estimate of the switching loss at fast switching transition and a good match with the conventional model at slow switching transition. Moreover, non-linearity of the MOSFET's output capacitance is considered in this model, suggesting a handy graphical method to determine the timing pattern and the switching loss properly in practice.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 287-291
Analytic model for power MOSFET turn-off switching loss under the effect of significant current diversion at fast switching events
The conventional method to evaluate switching loss of power MOSFETs is commonly based on the existence of the plateau gate-voltage region in the gate-charge plot. However, a very different behavior of the MOSFET with disappearance of the plateau region is observed under significant current diversion between channel and parasitic capacitances when a large gate drive current is applied to turn off the MOSFET. As the modern power converter is pursuing higher switching frequency, the gate drive current becomes larger accordingly to turn on and off the power MOSFET faster. Hence, this paper proposes an analytical model to predict the timing pattern and the switching loss more precisely in such conditions. Simulation and measurement have been conducted to validate this model, showing an accurate estimate of the switching loss at fast switching transition and a good match with the conventional model at slow switching transition. Moreover, non-linearity of the MOSFET's output capacitance is considered in this model, suggesting a handy graphical method to determine the timing pattern and the switching loss properly in practice.
- 29 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (8) , 6858-6868
High-Efficiency Fully Integrated Switched-Capacitor Voltage Regulator for Battery-Connected Applications in Low-Breakdown Process Technologies
Conventional implementations of fully integrated, battery-connected, switched-capacitor voltage regulators (SCVRs) require either thick-oxide mosfets or stacked thin-oxide mosfets as power switches to sustain the voltage stress induced by a nominal 3.7-V Li-ion battery voltage. These approaches, however, exacerbate power loss, thus unable to achieve good power efficiency. Therefore, this paper proposes a solution to overcome the breakdown issue while improving the power efficiency by using only nonstacked, thin-oxide mosfets. This is realized by using a three-state, low-voltage-stress SCVR with a cross-phase-switching technique to decrease the output impedance and increase the total equivalent capacitance in a multiphase configuration. A prototype 3:1 SCVR is implemented fully on-chip in a standard 130-nm CMOS process. The chip is capable of delivering a maximum load current of 45 mA with an input voltage range from 3.2 to 4 V. Measurement results show 78-80% efficiency over a range of output power 4-28 mW, and a power density up to 38 mW/nF. The measured output ripple is 30-50 mV over a load range of 11-45 mA, and the measured voltage droop is 69 mV with 200-ns settling time under a 13-mA load step.
- 29 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (8) , 6858-6868
High-Efficiency Fully Integrated Switched-Capacitor Voltage Regulator for Battery-Connected Applications in Low-Breakdown Process Technologies
Conventional implementations of fully integrated, battery-connected, switched-capacitor voltage regulators (SCVRs) require either thick-oxide mosfets or stacked thin-oxide mosfets as power switches to sustain the voltage stress induced by a nominal 3.7-V Li-ion battery voltage. These approaches, however, exacerbate power loss, thus unable to achieve good power efficiency. Therefore, this paper proposes a solution to overcome the breakdown issue while improving the power efficiency by using only nonstacked, thin-oxide mosfets. This is realized by using a three-state, low-voltage-stress SCVR with a cross-phase-switching technique to decrease the output impedance and increase the total equivalent capacitance in a multiphase configuration. A prototype 3:1 SCVR is implemented fully on-chip in a standard 130-nm CMOS process. The chip is capable of delivering a maximum load current of 45 mA with an input voltage range from 3.2 to 4 V. Measurement results show 78-80% efficiency over a range of output power 4-28 mW, and a power density up to 38 mW/nF. The measured output ripple is 30-50 mV over a load range of 11-45 mA, and the measured voltage droop is 69 mV with 200-ns settling time under a 13-mA load step.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 237-240
A 12V-to-0.9V active-clamp forward converter power block with planar transformer, standing slab inductor and direct edge solder to motherboard
DC-to-DC power supplies for CPUs or GPUs are critical components on the motherboard of modern computer systems. Converting an intermediate bus voltage (e.g. 12 V) to the core voltage (~0.9 V) of CPUs or GPUs must be efficient, compact and cost effective. This paper proposes an active-clamp forward converter (ACFC) power block to supply core voltage on a motherboard. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to save motherboard area. A low loss, compact planar transformer is designed into the ACFC power block PCB. A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the DC loss in the current path. Experimental results show a peak efficiency of 90.4% with a 12 V input and 0.9 V output for an output current of 25 A.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 237-240
A 12V-to-0.9V active-clamp forward converter power block with planar transformer, standing slab inductor and direct edge solder to motherboard
DC-to-DC power supplies for CPUs or GPUs are critical components on the motherboard of modern computer systems. Converting an intermediate bus voltage (e.g. 12 V) to the core voltage (~0.9 V) of CPUs or GPUs must be efficient, compact and cost effective. This paper proposes an active-clamp forward converter (ACFC) power block to supply core voltage on a motherboard. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to save motherboard area. A low loss, compact planar transformer is designed into the ACFC power block PCB. A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the DC loss in the current path. Experimental results show a peak efficiency of 90.4% with a 12 V input and 0.9 V output for an output current of 25 A.