DHDeukhyoun Heo

Deukhyoun Heo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Deukhyoun Heo has a total of 65 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Low-Jitter, Energy-Efficient 6/12-GHz PhaseInterpolator With 0.18mW/GHz in 65-nm CMOS

    by Soumen Mohapatra, Emad Afshar, Zhiyuan Zhou, Deukhyoun Heo

    This article presents a novel low-power, low-noise phase interpolator (PI) with high resolution designed for diverse applications such as local clock generation in clock data recovery (CDR) to sample time-interleaved analog-to-digital-converter (TI-ADC) and baseband delay beamforming. The proposed PI, implemented in 65-nm CMOS, utilizes a ramp signal with constant slope and swing, whose DC level is dynamically modulated by the input code. This design enables high-speed operation with a power efficiency of 0.18mW/GHz and reduced noise levels. Integration of a four-stage injection-locked ring oscillator (RO) at the final stage eliminates the need for an input delay-locked loop (DLL), duty-cycle corrector (DCC), and output quadrature generator. This innovative design simultaneously generates a 4-phase output at 6GHz with an IQ error below 0.9° and a 2-phase output at 12GHz. The fabricated PI covers the full 360° range while consuming only 2.2mW and occupying a compact 0.025mm2. It also achieves an rms jitter of just 68 fs, with differential non-linearity (DNL) and integral non-linearity (INL) measured at 0.9 and 1.9 LSB, respectively.

  • A Compact Single-Ended Common-Base Doherty PA in 90-nm BiCMOS With 37.3% Peak PAE for 5G Beamforming Arrays

    by Mohammad Ali Mokri, Emad Afshar, Aminul Hoque, Soodeh Miraslani, Shahriar Mirabbasi, Deukhyoun Heo

    This article presents a back-off efficient power amplifier (PA) for mm-wave 5G and upcoming 6G beamforming phased array transceivers (PATs), incorporating advanced circuit designs and novel implementations in both passive and active components. Conventional back-off efficient PAs in the mm-wave frequency range occupy a large chip area, making it hard to fit them into PATs. To overcome this issue, we propose a compact back-off efficient Doherty PA (DPA) with a common base (CB) structure as the core of the PA and small low-loss passive elements. In addition, the proposed architecture moves the role of the input hybrid coupler to the interstage matching network while maintaining DPA functionality. The interstage matching provides the required phases for the main and auxiliary PAs, power division, and impedance matching. The PA prototype is fabricated in the GlobalFoundries 90-nm BiCMOS (9 HP) process. It achieves a peak gain of 20.4 dB at 28.45 GHz with a 1-dB bandwidth of 4.45 GHz. Under large-signal conditions, it archives $>$ 19.5-dBm $P_{\rm sat}$ with $>$ 36% $\text{PAE}_{\rm sat}$ . Its $P_{1\text{dB}}$ at 26, 28, and 30 GHz are 19.4, 19.3, and 19.3 dBm with 38.5%, 37.3%, and 36.8% $\text{PAE}_{1\, \text{dB}}$ , respectively. In the 6-dB power back-off region, it reaches efficiencies of 29.1%, 31.1%, and 29.3% at 26, 28, and 30 GHz, respectively. When tested with the NR-FR2 test model at these frequencies, the PA achieves $P_{\rm avg}$ of 8.25, 8.45, and 8 dBm, and $\text{PAE}_{\rm avg}$ of 13.9%, 14.5%, and 13.7% for a 400 M 1-CC 64-QAM signal, maintaining an rms error vector magnitude ( $\text{EVM}_{\rm rms}$ ) of $-$ 25.8, $-$ 25.8, and $-$ 25.7 dB. In addition, in adjacent channel power ratio (ACPR) tests, the PA achieves $-$ 27, $-$ 26.2, and $-$ 30.8 dBc on the lower side and $-$ 28.4, $-$ 28.5, and $-$ 27.6 dBc on the higher side channels at 26, 28, and 30 GHz, respectively.


  • A Triple-Band, High DC-to-RF Efficiency, Multicore VCO With a Dual-Path Inductor and Mode-Switching Capacitor

    by Aminul Hoque, Deukhyoun Heo

    This article introduces an innovative four-port dual-path inductor designed to deliver two distinct inductance values to the resonator of a voltage-controlled oscillator (VCO). The switching between the inductor’s two excitation modes, even and odd, is determined by the differential excitation’s input polarity, eliminating the need for a series switch. Thus, the inductor has a high-quality factor ( $Q$ ) in both modes. The inductances in these modes can be independently set based on desired frequencies. This inductance change achieves coarse frequency tuning, while fine-tuning is realized by a conventional 2-bit capacitor bank with a small-size varactor. This inductor is well suited for designing multiband VCOs aimed at widely spaced operation frequency bands. Apart from the inductance change, a particular case of mode-switching capacitor is employed to extend to another frequency band in between the low and middle bands, achieving triple-band oscillation. As a result, this article presents two VCOs designed using the proposed inductor: one in class-D biasing in a 65-nm CMOS process and another with class-B biasing in a 180-nm BiCMOS process. Both VCOs successfully oscillate across three distinct frequency bands, centered at 19, 28, and 36 GHz, while maintaining outstanding phase noise and minimal power consumption. Measurement results show good match with simulation, resulting in a peak figure of merit (FoM) of 185.7 dBc/Hz at 18.5 GHz, and occupy 0.088- $\text{mm}^2$ (250 $\times$ 350 $\mu$ m) area in both processes.


  • A Dual-Path Transformer-Based Multiband Power Amplifier for mm-Wave 5G Applications

    by Mohammad Ali Mokri, Soodeh Miraslani, Aminul Hoque, Deukhyoun Heo

    This article presents a dual-band power amplifier for 28 and 39 GHz frequency bands based on a new dual-path transformer (DPT). This DPT can provide two optimum inductive values at two different frequency bands to optimally design the matching networks for each band without using any switch circuitries. It operates as the output and input matching networks in a parallel power combiner and divider, respectively. DPT-based PA breaks the trade-off between bandwidth and performance in conventional wideband PAs by separating one whole wideband into two narrow bands providing optimum input and output matchings for each band. The DPT-based PA has two input and two output ports. One set of input and output ports is dedicated to a lower frequency band and the other set of input and outport ports can be used for a higher frequency band. Each output port can drive a separate antenna in a phased array for each frequency band. The proposed PA prototype is fabricated in a 65 nm CMOS process achieving 15.3 and 14.0 dBm of saturated output power in 28 and 39 GHz. The peak efficiency of the PA is 34.1% and 30.2% at 28 and 39 GHz frequency bands. The PA has a measured EVM with 64-QAM modulated signal in both frequency bands showing $-$ 25.03 and $-$ 25.10 dB in the low and higher frequency bands, respectively.


  • A 14 GHz Integer-N Sub-Sampling PLL With RMS-Jitter of 85.4 fs Occupying an Ultra Low Area of 0.0918 mm2

    by Dipan Kar, Soumen Mohapatra, Aminul Hoque, Deukhyoun Heo

    This paper presents a 14 GHz sub-sampling PLL (SSPLL) with its phase noise analysis for Ku-band wireless transceivers. The performance enhancement of the phase-locked loop (PLL) over single-stage PLL in terms of jitter and power consumption is theoretically presented and verified with measured results. The proposed capacitor multiplier reduces the size of the loop filter capacitor by 28 times. The active capacitor VCO decreases the out-band phase noise while consuming less power. Fabricated in a 65 nm CMOS process with a core active area of 0.0918 $mm^{2}$ , the SSPLL operates at 1.2 V supply achieving 13.2-14.8 GHz tuning range, 85.4 fs integrated jitter at 14 GHz, 8.42 mW power consumption, and -252.12 dB figure-of-merit (FoM). The measured results in-band and out-band phase noises of -108.6 dBc/Hz at a 1 MHz offset and -128.9 dBc/Hz at a 10 MHz offset, respectively.


  • Highly Efficient Multiband Harmonic-Tuned GaN RF Synchronous Rectifier

    by Aminul Hoque, Sheikh Nijam Ali, Mohammad Ali Mokri, Srinivasan Gopal, Mohammad Chahardori, Thomas Johnson, Deukhyoun Heo

    This article presents a highly efficient GaN-based harmonic-tuned multiband RF rectifier for wireless power transfer (WPT) applications. The rectifier has been implemented by incorporating a microstrip coupler and a transmission line-based phase shifter to convert a power amplifier (PA) into a synchronous rectifier based on the time-reversal duality principle. The proposed rectifier provides a compact solution for wireless power charging systems while supporting dual-bands. The microstrip coupler is used to derive the gate driving signal for the device, which requires a weak coupling from the input RF signal. The coupler has been characterized separately for wideband operation from 1 to 3 GHz with only 0.3-dB insertion loss. Measurement results show that the rectifier has 77% and 75% efficiencies at 1.17 and 2.4 GHz, respectively, when the input RF power is 10 W. The rectifier shows $>$ 50% efficiency for input power levels down to 1.5 W. To the best of the authors’ knowledge, this rectifier presents one of the highest RF-to-dc rectification efficiencies in dual-band operation for a watt-level RF input power.


  • Empowering 5G and Beyond: Advanced Multiband Signal Generation and High-Performance Signal Synthesis Techniques for Communications and Sensing Systems [From the Guest Editor’s Desk]

    by Deukhyoun Heo

    It is with great enthusiasm that I introduce this focused issue of IEEE Microwave Magazine , focusing on state-of-the-art advances in the field of signal generation. As an active member of the IEEE Microwave Theory and Technology Society Biological Effects and Medical Applications Technical Committee (TC-10), I am pleased to present two in-depth articles that thoroughly investigate the complex world of millimeter (mm)-wave signal generation for multiband operation and high-quality signal generation.


  • Spanning the Spectrum: High-Performance Signal Source Design for the Millimeter-Wave Age

    by Joe Baylon, Aminul Hoque, Deukhyoun Heo

    The millimeter-wave (mm-wave) frequency range is consumer wireless technology’s next frontier. Next-generation cellular technologies demand ever-increasing data rates, reduced latency, and robust service for a massive number of users. The mm-wave wireless systems operating in the frequency range from 10 to 100 GHz have the potential to satisfy the requirements presented by these consumer demands [1] . High carrier frequencies offer increased communication bandwidths for improved throughput with relatively small fractional bandwidths. Furthermore, because the development of mm-wave wireless and cellular technologies is in its infancy, relatively few external interferers exist at these frequencies. Thanks to the continued scaling of CMOS devices and increased transit and maximum frequencies, the integration of high-performance mm-wave transceivers is more viable than ever before. Transceiver integration further benefits from the decreased size of passive devices with high-frequency operation, decreasing silicon area and minimizing parasitic effects. Thanks to these benefits, 5G hardware research has focused on exploring limitations and establishing design principles for integrated CMOS mm-wave front ends.


  • Low-Power Process and Temperature-Invariant Constant Slope-and-Swing Ramp-Based Phase Interpolator

    by Soumen Mohapatra, Chung-Ching Lin, Subhanshu Gupta, Deukhyoun Heo

    This article presents a process-and temperature-invariant high-resolution and highly linear low-power phase interpolator (PI) as an enabler for discrete-time spatial signal processors (SSPs) and for various mixed-mode RF transceiver architectures. Using current integration techniques, the proposed PI generates an adaptable constant slope-and-swing ramp signal to achieve significantly lower power suited for multiple antenna elements. Switched-capacitor-based bias generation enables tracking the ramp generator over process, voltage, and temperature enhancing the PI linearity. The 7-bit PI realized in the 65-nm CMOS technology can generate full delay range with a resolution of 4.88 ps at 1.6-GHz input frequency. The PI consumes a power of 503 $\mu$ W and occupies an active area of 0.021 mm $^2$ with a jitter of 0.410 ps for a 1.6-GHz operation and measured DNL and INL of 0.52 and 0.52 LSB, respectively.


  • An Inductor-First Single-Inductor Multiple-Output Hybrid DC–DC Converter With Integrated Flying Capacitor for SoC Applications

    by Zhiyuan Zhou, Nghia Tang, Bai Nguyen, Wookpyo Hong, Partha Pratim Pande, Ram K. Krishnamurthy, Deukhyoun Heo

    With the increasing complexity of highly integrated system on chips (SoCs), the power management system (PMS) is required to provide several power supplies efficiently for individual blocks. This paper presents a single-inductor multiple-output (SIMO) inductor-first hybrid converter that generates three outputs between 0.4V and 1.6V from a 1.8V input. The proposed multiple-output hybrid power stage can improve the conversion efficiency by reducing inductor current while extending the output voltage range compared with the existing hybrid topologies. In addition, the proposed converter employs an on-chip switched-capacitor power stage (SCPS) with a dual-switching frequency technique, resulting in a fast response time, low cross-regulation, and reduced number of on-chip pads. Measurement results show that the converter achieves a peak efficiency of 87.5% with the maximum output current of 450mA. The converter is integrated with a fast voltage regulation loop with 500MHz system clock to achieve a less than 0.01mA/mV cross-regulation and a maximum 20mV overshoot at full-load transient response. The design is fabricated in the standard 180nm CMOS technology.