Zhan Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhan Gao has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Carlo De Santi
University of Padova
6 shared publications - Enrico Zanoni
University of Padova
6 shared publications - Gaudenzio Meneghesso
University of Padova
6 shared publications - Matteo Meneghini
University of Padova
6 shared publications - Mirko Fornasier
Department of Information Engineering, University of Padua, Padua, Italy
4 shared publications - Alessandro Chini
Department of Engineering “Enzo Ferrari”, Università di Modena e Reggio Emilia, 41125 Modena, Italy
3 shared publications
Latest Publications
- Open Access
- 1 July 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (7) , 075008
1200 V-class vertical GaN-on-GaN p – i – n diodes with two-zone step-etched junction termination extension
To fully realize the potential of vertical GaN power devices, proper junction termination methods are needed to reduce the electric field at the device periphery, leading obtaining breakdown voltage values as close as possible to the ideal values. Among these methods, the junction termination extension (JTE), fabricated using selective-area doping using ion implantation or by appropriate shaping of epitaxial p-type layers using plasma etching (step-etched JTE), has proven to be especially effective in obtaining high, robust, non-destructive, avalanche breakdown. However, more research is needed to fully demonstrate the effectiveness and usability of step-etched JTE structures for vertical GaN power devices, especially when supported by measurements of a large, statistically significant number of devices. In this work, we present the fabrication and characterization of 1200 V-class vertical GaN p – i – n diodes with two-zone step-etched JTE structures. By varying the JTE thickness, a high breakdown voltage of over 1700 V and up to 1806 V was obtained, with a termination efficiency up to 91% ideal value. Moreover, an analysis of the measurement of a large number of fabricated devices was also presented, showing low statistical dispersion and tight distribution of breakdown voltage values.
- 1 July 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (7) , 075008
Open Access1200 V-class vertical GaN-on-GaN p – i – n diodes with two-zone step-etched junction termination extension
To fully realize the potential of vertical GaN power devices, proper junction termination methods are needed to reduce the electric field at the device periphery, leading obtaining breakdown voltage values as close as possible to the ideal values. Among these methods, the junction termination extension (JTE), fabricated using selective-area doping using ion implantation or by appropriate shaping of epitaxial p-type layers using plasma etching (step-etched JTE), has proven to be especially effective in obtaining high, robust, non-destructive, avalanche breakdown. However, more research is needed to fully demonstrate the effectiveness and usability of step-etched JTE structures for vertical GaN power devices, especially when supported by measurements of a large, statistically significant number of devices. In this work, we present the fabrication and characterization of 1200 V-class vertical GaN p – i – n diodes with two-zone step-etched JTE structures. By varying the JTE thickness, a high breakdown voltage of over 1700 V and up to 1806 V was obtained, with a termination efficiency up to 91% ideal value. Moreover, an analysis of the measurement of a large number of fabricated devices was also presented, showing low statistical dispersion and tight distribution of breakdown voltage values.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 42-51
Deep-Level Effects in Back-Barrier-Scaled GaN HEMTs
Drain current transient spectroscopy is adopted to study deep-level effects in scaled GaN high electron mobility transistors (HEMTs) and to identify trap time constants in different bias conditions, needed for the definition of compact circuit-level models including dispersion effects. Fe- and C-doped reference devices are compared to devices adopting AlGaN back-barriers or buffer-free devices where the GaN channel was grown directly on the AlN nucleation layer. We identified an acceptor trap at the GaN/back-barrier interface (Ea = 0.7–0.9 eV) common to both back-barrier and buffer-free devices. This trap is correlated with an overshoot of the transconductance, $g_{\mathrm {m}}$ , due to sudden trap ionization and negative threshold voltage shift occurring during $I_{\mathrm {D}}$ versus $V_{\mathrm {GS}}$ dc measurements. We demonstrate that the electron detrapping mechanism is photoionization, due to bremsstrahlung radiation emitted by the devices in hot-electron regime. When bias is applied during the recovery phase emission rate increases by several orders of magnitude. This makes traps time constants heavily dependent on $V_{\mathrm {DS}}$ and $V_{\mathrm {GS}}$ and requires to be suitably addressed in compact models. Finally, data concerning trapping effects consequent to the application of RF signal are discussed.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 42-51
Deep-Level Effects in Back-Barrier-Scaled GaN HEMTs
Drain current transient spectroscopy is adopted to study deep-level effects in scaled GaN high electron mobility transistors (HEMTs) and to identify trap time constants in different bias conditions, needed for the definition of compact circuit-level models including dispersion effects. Fe- and C-doped reference devices are compared to devices adopting AlGaN back-barriers or buffer-free devices where the GaN channel was grown directly on the AlN nucleation layer. We identified an acceptor trap at the GaN/back-barrier interface (Ea = 0.7–0.9 eV) common to both back-barrier and buffer-free devices. This trap is correlated with an overshoot of the transconductance, $g_{\mathrm {m}}$ , due to sudden trap ionization and negative threshold voltage shift occurring during $I_{\mathrm {D}}$ versus $V_{\mathrm {GS}}$ dc measurements. We demonstrate that the electron detrapping mechanism is photoionization, due to bremsstrahlung radiation emitted by the devices in hot-electron regime. When bias is applied during the recovery phase emission rate increases by several orders of magnitude. This makes traps time constants heavily dependent on $V_{\mathrm {DS}}$ and $V_{\mathrm {GS}}$ and requires to be suitably addressed in compact models. Finally, data concerning trapping effects consequent to the application of RF signal are discussed.
- 3 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23)
Vertical GaN p–n Diodes with Ultralow Bevel Angle Mesa Termination Fabricated Using Photoresist Reflow and Single Cl 2 /BCl 3 /SF 6 Etching Step
Herein, vertical GaN p–i–n diodes with ultralow bevel mesa (ULBM) termination structures are successfully fabricated using photoresist reflow and single Cl2 2 /BCl 3 /SF 6 etching step. Using the developed method, bevel mesa structures with slope angles as low as ≈0.8°–1° are fabricated by reducing the GaN etch rate and improving GaN‐to‐photoresist mask etch selectivity through the addition of SF 6 to the commonly used Cl 2 /BCl 3 ‐based plasma. The fabricated diodes with ULBM structures exhibit a low leakage current and repeatable, nondestructive breakdown resulting from avalanche effect, demonstrating termination efficiency of ≈80% with breakdown voltage of about ≈−600 V. This is in contrast to the diodes with nearly vertical or ≈13° bevel mesa structures, for which much lower, often destructive, breakdown voltage (≈ − 350 ÷ −400 V) and higher leakage current are obtained.
- 3 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23)
Vertical GaN p–n Diodes with Ultralow Bevel Angle Mesa Termination Fabricated Using Photoresist Reflow and Single Cl 2 /BCl 3 /SF 6 Etching Step
Herein, vertical GaN p–i–n diodes with ultralow bevel mesa (ULBM) termination structures are successfully fabricated using photoresist reflow and single Cl2 2 /BCl 3 /SF 6 etching step. Using the developed method, bevel mesa structures with slope angles as low as ≈0.8°–1° are fabricated by reducing the GaN etch rate and improving GaN‐to‐photoresist mask etch selectivity through the addition of SF 6 to the commonly used Cl 2 /BCl 3 ‐based plasma. The fabricated diodes with ULBM structures exhibit a low leakage current and repeatable, nondestructive breakdown resulting from avalanche effect, demonstrating termination efficiency of ≈80% with breakdown voltage of about ≈−600 V. This is in contrast to the diodes with nearly vertical or ≈13° bevel mesa structures, for which much lower, often destructive, breakdown voltage (≈ − 350 ÷ −400 V) and higher leakage current are obtained.
- Open Access
- 27 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (3) , 369-372
Self-Induced Photoionization of Traps in Buffer-Free AlGaN/GaN HEMTs
Detrapping mechanisms and their dependence on applied bias have been studied in buffer-free AlGaN/GaN HEMTs on SiC. It is shown that the detrapping time constant decreases by orders of magnitude when the device is biased in semi-on conditions, or if the gate Schottky junction is forward biased with source and drain at ground. Despite completely different mechanisms are involved concerning charge transport and light emission, both bias conditions induce emission of high-energy photons (E>2 eV) which can photoionize traps, thus enhancing the recovery process. Data shown here suggest that a realistic description of GaN device behaviour can only be achieved by including optical effects in device modeling.
- 27 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (3) , 369-372
Open AccessSelf-Induced Photoionization of Traps in Buffer-Free AlGaN/GaN HEMTs
Detrapping mechanisms and their dependence on applied bias have been studied in buffer-free AlGaN/GaN HEMTs on SiC. It is shown that the detrapping time constant decreases by orders of magnitude when the device is biased in semi-on conditions, or if the gate Schottky junction is forward biased with source and drain at ground. Despite completely different mechanisms are involved concerning charge transport and light emission, both bias conditions induce emission of high-energy photons (E>2 eV) which can photoionize traps, thus enhancing the recovery process. Data shown here suggest that a realistic description of GaN device behaviour can only be achieved by including optical effects in device modeling.
- Open Access
- 31 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (12) , 6256-6261
Dynamic Behavior of Threshold Voltage and I D – V DS Kink in AlGaN/GaN HEMTs Due to Poole–Frenkel Effect
The kink effect in field-effect transistors (FETs) consists in a sudden increase in drain current, $\textit{I}_{\text{D}}$ , during a drain voltage sweep and leading to a higher $\textit{I}_{\text{D}}$ saturation value. We report new experimental data concerning the dynamic behavior of the “kink” in AlGaN/GaN HEMTs and correlate them with deep levels. The results demonstrate the role of the Poole–Frenkel effect in determining the occurrence of the kink and identify the experimental conditions that make it observable.
- 31 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (12) , 6256-6261
Open AccessDynamic Behavior of Threshold Voltage and I D – V DS Kink in AlGaN/GaN HEMTs Due to Poole–Frenkel Effect
The kink effect in field-effect transistors (FETs) consists in a sudden increase in drain current, $\textit{I}_{\text{D}}$ , during a drain voltage sweep and leading to a higher $\textit{I}_{\text{D}}$ saturation value. We report new experimental data concerning the dynamic behavior of the “kink” in AlGaN/GaN HEMTs and correlate them with deep levels. The results demonstrate the role of the Poole–Frenkel effect in determining the occurrence of the kink and identify the experimental conditions that make it observable.
- Top Cited PapersOpen Access
- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1396-1407
Microwave and Millimeter-Wave GaN HEMTs: Impact of Epitaxial Structure on Short-Channel Effects, Electron Trapping, and Reliability
Application of gallium nitride high-electron-mobility transistors (GaN HEMTs) to millimeter-wave power amplifiers requires gate length scaling below 150 nm: in order to control short-channel effects, the gate-to-channel distance must be decreased, and the device epitaxial structure has to be completely redesigned. A high 2-D electron gas (2DEG) carrier density can be preserved even with a very thin top barrier layer by substituting AlGaN with AlN, InAl(Ga)N, or ScAlN. Moreover, to prevent interaction of hot electrons with compensating impurities and defects in the doped GaN buffer, the latter has to be separated from the channel by a back barrier. Other device designs consist in adopting a graded channel (which controls the electric field) or to adopt nitrogen-polar (N-polar) GaN growth (which decreases the distance between gate and channel, thus attenuating short-channel effects). The aim of this article is to review the various options for controlling short-channel effects, improve off-state characteristics, and reduce drain–source leakage current. Advantages and potential drawbacks of each proposed solution are analyzed in terms of current collapse (CC), dispersion effects, and reliability.
- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1396-1407
Top Cited PapersOpen AccessMicrowave and Millimeter-Wave GaN HEMTs: Impact of Epitaxial Structure on Short-Channel Effects, Electron Trapping, and Reliability
Application of gallium nitride high-electron-mobility transistors (GaN HEMTs) to millimeter-wave power amplifiers requires gate length scaling below 150 nm: in order to control short-channel effects, the gate-to-channel distance must be decreased, and the device epitaxial structure has to be completely redesigned. A high 2-D electron gas (2DEG) carrier density can be preserved even with a very thin top barrier layer by substituting AlGaN with AlN, InAl(Ga)N, or ScAlN. Moreover, to prevent interaction of hot electrons with compensating impurities and defects in the doped GaN buffer, the latter has to be separated from the channel by a back barrier. Other device designs consist in adopting a graded channel (which controls the electric field) or to adopt nitrogen-polar (N-polar) GaN growth (which decreases the distance between gate and channel, thus attenuating short-channel effects). The aim of this article is to review the various options for controlling short-channel effects, improve off-state characteristics, and reduce drain–source leakage current. Advantages and potential drawbacks of each proposed solution are analyzed in terms of current collapse (CC), dispersion effects, and reliability.
- Open Access
- 14 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (4) , 453-460
Mechanisms of Step-Stress Degradation in Carbon-Doped 0.15-μm AlGaN/GaN HEMTs for Power RF Applications
We discuss the degradation mechanisms of C-doped 0.15-μm gate AlGaN/GaN HEMTs tested by drain step-stress experiments. Experimental results show that these devices exhibit cumulative degradation effects during the step stress experiments in terms of either (i) transconductance (gm) decrease without any threshold-voltage (VT) change under OFF-state stress, or (ii) both VT and gm decrease under ON-state stress conditions. To aid the interpretation of the experiments, two-dimensional hydrodynamic device simulations were carried out. Based on obtained results, we attribute the gm decrease accumulating under OFF-state stress to hole emission from CN acceptor traps in the gate-drain access region of the buffer, resulting in an increase in the drain access resistance. On the other hand, under ON-state stress, channel hot electrons are suggested to be injected into the buffer under the gate and in the gate-drain region where they can be captured by CN traps, leading to VT and gm degradation, respectively.
- 14 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (4) , 453-460
Open AccessMechanisms of Step-Stress Degradation in Carbon-Doped 0.15-μm AlGaN/GaN HEMTs for Power RF Applications
We discuss the degradation mechanisms of C-doped 0.15-μm gate AlGaN/GaN HEMTs tested by drain step-stress experiments. Experimental results show that these devices exhibit cumulative degradation effects during the step stress experiments in terms of either (i) transconductance (gm) decrease without any threshold-voltage (VT) change under OFF-state stress, or (ii) both VT and gm decrease under ON-state stress conditions. To aid the interpretation of the experiments, two-dimensional hydrodynamic device simulations were carried out. Based on obtained results, we attribute the gm decrease accumulating under OFF-state stress to hole emission from CN acceptor traps in the gate-drain access region of the buffer, resulting in an increase in the drain access resistance. On the other hand, under ON-state stress, channel hot electrons are suggested to be injected into the buffer under the gate and in the gate-drain region where they can be captured by CN traps, leading to VT and gm degradation, respectively.
- Open Access
- 9 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (6) , 3005-3010
Transconductance Overshoot, a New Trap-Related Effect in AlGaN/GaN HEMTs
DC characteristics of AlGaN/GaN HEMTs with different thickness values of the undoped GaN channel layer were compared. An abnormal transconductance ( ${g}_{m}{)}$ overshoot accompanied by a negative threshold voltage ( ${V}_{\text {TH}}{)}$ shift was observed during ${I}_{\text {DS}}$ – ${V}_{\text {GS}}$ sweep in devices with thinner GaN layer. At the same time, a non-monotonic increase in gate current was observed. In OFF-state, electron trapping occurs in the undoped GaN layer or at the GaN/AlN interface, leading to a positive ${V}_{\text {TH}}$ shift. When the device is turning on at a sufficiently high ${V}_{\text {DS}}$ , electron de-trapping occurs due to trap impact-ionization; consequently, ${V}_{\text {TH}}$ and therefore ${I}_{\text {D}}$ suddenly recovers, leading to the ${g}_{m}$ overshoot effect. These effects are attributed to electron trap impact-ionization and consequent modulation of the device’s electric field.
- 9 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (6) , 3005-3010
Open AccessTransconductance Overshoot, a New Trap-Related Effect in AlGaN/GaN HEMTs
DC characteristics of AlGaN/GaN HEMTs with different thickness values of the undoped GaN channel layer were compared. An abnormal transconductance ( ${g}_{m}{)}$ overshoot accompanied by a negative threshold voltage ( ${V}_{\text {TH}}{)}$ shift was observed during ${I}_{\text {DS}}$ – ${V}_{\text {GS}}$ sweep in devices with thinner GaN layer. At the same time, a non-monotonic increase in gate current was observed. In OFF-state, electron trapping occurs in the undoped GaN layer or at the GaN/AlN interface, leading to a positive ${V}_{\text {TH}}$ shift. When the device is turning on at a sufficiently high ${V}_{\text {DS}}$ , electron de-trapping occurs due to trap impact-ionization; consequently, ${V}_{\text {TH}}$ and therefore ${I}_{\text {D}}$ suddenly recovers, leading to the ${g}_{m}$ overshoot effect. These effects are attributed to electron trap impact-ionization and consequent modulation of the device’s electric field.
- 15 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 611-614
Effects of Gd2O3 Gate Dielectric on Proton-Irradiated AlGaN/GaN HEMTs
AlGaN/GaN high electron mobility transistors (HEMTs) and MOS-HEMTs using Gd 2 O 3 as gate dielectric were irradiated with 2-MeV protons up to fluence of 1 × 10 15 cm -2 . Results showed that proton irradiation causes a strong degradation in the Schottky gate devices, featured by more than three orders of magnitude increase in reverse leakage current, a 30% decrease in maximum drain current, and the same percentage of increase in ON-resistance, respectively. Scanning transmission electron microscopy showed that radiation induced a diffusion of Ni into Au in the gate and void formation, degrading the transistors' characteristics. The Gd 2 O 3 gate dielectric layer prevented this diffusion and void formation. MOS-HEMTs with Gd 2 O 3 gate dielectric show 50% less decrease of performance under proton irradiation than Schottky gate HEMTs (conventional HEMTs). The trapping effects of Gd 2 O 3 gate layer before and after irradiation are also discussed.
- 15 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (5) , 611-614
Effects of Gd2O3 Gate Dielectric on Proton-Irradiated AlGaN/GaN HEMTs
AlGaN/GaN high electron mobility transistors (HEMTs) and MOS-HEMTs using Gd 2 O 3 as gate dielectric were irradiated with 2-MeV protons up to fluence of 1 × 10 15 cm -2 . Results showed that proton irradiation causes a strong degradation in the Schottky gate devices, featured by more than three orders of magnitude increase in reverse leakage current, a 30% decrease in maximum drain current, and the same percentage of increase in ON-resistance, respectively. Scanning transmission electron microscopy showed that radiation induced a diffusion of Ni into Au in the gate and void formation, degrading the transistors' characteristics. The Gd 2 O 3 gate dielectric layer prevented this diffusion and void formation. MOS-HEMTs with Gd 2 O 3 gate dielectric show 50% less decrease of performance under proton irradiation than Schottky gate HEMTs (conventional HEMTs). The trapping effects of Gd 2 O 3 gate layer before and after irradiation are also discussed.
- 23 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 63 (7) , 2729-2734
Thermal Assessment of AlGaN/GaN MOS-HEMTs on Si Substrate Using Gd2O3 as Gate Dielectric
Thermal stability of AlGaN/GaN metal–oxide–semiconductor high-electron mobility transistors (MOS-HEMTs) and diodes using Gd 2 O 3 is investigated by means of different thermal tests. DC and pulsed $I$ – $V$ characterization of the devices before and after the processes shows that the devices with Gd 2 O 3 dielectric layer have more than three orders of magnitude lower leakage current, higher ON/OFF ratio of about $10^{8}$ , and better thermal stability after the long thermal storage test (500 °C, 8 days) compared with conventional devices. In addition, no hysteresis and a stable threshold voltage were observed after a short thermal test (500 °C, 5 min) in the MOS diodes, in good agreement with the lower trapping effects observed in the MOS-HEMTs.
- 23 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 63 (7) , 2729-2734
Thermal Assessment of AlGaN/GaN MOS-HEMTs on Si Substrate Using Gd2O3 as Gate Dielectric
Thermal stability of AlGaN/GaN metal–oxide–semiconductor high-electron mobility transistors (MOS-HEMTs) and diodes using Gd 2 O 3 is investigated by means of different thermal tests. DC and pulsed $I$ – $V$ characterization of the devices before and after the processes shows that the devices with Gd 2 O 3 dielectric layer have more than three orders of magnitude lower leakage current, higher ON/OFF ratio of about $10^{8}$ , and better thermal stability after the long thermal storage test (500 °C, 8 days) compared with conventional devices. In addition, no hysteresis and a stable threshold voltage were observed after a short thermal test (500 °C, 5 min) in the MOS diodes, in good agreement with the lower trapping effects observed in the MOS-HEMTs.