Thomas Martin Lillo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Thomas Martin Lillo has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
S.A. Hackney
7 shared publications- David P. Field
School of Mechanical and Materials Engineering, Washington State University
6 shared publications M.R. Plichta
6 shared publications- Isabella Johanna Van Rooyen
Idaho National Laboratory
5 shared publications - Wen Jiang
Idaho National Laboratory (INL), Idaho Falls, ID (United States)
5 shared publications J. Macheret
Idaho National Engineering and Environmental Laboratory, Idaho Falls, ID 83415
4 shared publications
Latest Publications
- 30 April 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 2nd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 2nd quarter of FY20, calibration of the creep model was made using experimental creep data on base metal at temperatures between 700-800 C. The model simulated primary and secondary creep behavior at these temperatures but tended to over estimate creep strain in the tertiary regime at 700 C while underestimating it at higher temperatures. Additional issues were also discovered and will be looked at in greater detail in the 3rd quarter of FY20.
- 30 April 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 2nd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 2nd quarter of FY20, calibration of the creep model was made using experimental creep data on base metal at temperatures between 700-800 C. The model simulated primary and secondary creep behavior at these temperatures but tended to over estimate creep strain in the tertiary regime at 700 C while underestimating it at higher temperatures. Additional issues were also discovered and will be looked at in greater detail in the 3rd quarter of FY20.
- 4 February 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY20, efforts focused on calibrating a computational model using experimental data. The experimental creep data obtain from specimens containing weld metal exhibit considerable inherent variability making calibration of the computational difficult and may not result in an accurate model.
- 4 February 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY20, efforts focused on calibrating a computational model using experimental data. The experimental creep data obtain from specimens containing weld metal exhibit considerable inherent variability making calibration of the computational difficult and may not result in an accurate model.
- 28 January 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 1st Quarter, Multi-pass Hybrid Laser Arc Welding of Alloy 740H
During the first quarter of FY20, work focused on implementing a subcontract with Penn State University to collaborate on the project. Significant delays prevented the subcontract from being placed until the end of December. As a result only limited progress was made on the project. Required equipment was researched and ordered during the first quarter but will not be delivered until the middle of the second quarter of FY20. Delays are not expected to adversely impact the schedule of the project.
- 28 January 2020
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY20, 1st Quarter, Multi-pass Hybrid Laser Arc Welding of Alloy 740H
During the first quarter of FY20, work focused on implementing a subcontract with Penn State University to collaborate on the project. Significant delays prevented the subcontract from being placed until the end of December. As a result only limited progress was made on the project. Required equipment was researched and ordered during the first quarter but will not be delivered until the middle of the second quarter of FY20. Delays are not expected to adversely impact the schedule of the project.
- 4 November 2019
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY19, 4th Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 4th quarter of FY19, diffusional creep effects, based on the local stress tensor, was incorporated into the modeling and simulation efforts on thick section welds of Alloy 740H. The model is now complete and addresses both dislocation-based creep as well as diffusional creep mechanisms. Preliminary result indicate the model is now capable of predicting a transition from secondary creep to tertiary creep. Calibration of the model using experimental creep data remains to be performed and will be done in the first quarter of FY20.
- 4 November 2019
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY19, 4th Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 4th quarter of FY19, diffusional creep effects, based on the local stress tensor, was incorporated into the modeling and simulation efforts on thick section welds of Alloy 740H. The model is now complete and addresses both dislocation-based creep as well as diffusional creep mechanisms. Preliminary result indicate the model is now capable of predicting a transition from secondary creep to tertiary creep. Calibration of the model using experimental creep data remains to be performed and will be done in the first quarter of FY20.
- 23 January 2018
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY18, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 1st quarter of FY18 modeling and simulation of the creep of thick section welds continued although some workscope from FY17 still needs to be completed. Four stress drop tests to determine the threshold stress for creep in Alloy 740H were carried out. One has finished and post-test analysis shows a threshold creep stress of about 67 MPa which is lower than that found in a previous program for Alloy 617 at the same temperature. Alloy 617 is not as creep resistant as Alloy 740H and the reason for the lower than expected threshold stress for Alloy 740H is being investigated further. Also analysis of the gamma prime particle size in an aging study closely follows the aging characteristics of gamma prime in Alloy 617. Further analysis of other aged materials will be carried out during the 2nd quarter of FY18 to confirm that the aging characteristic of Alloy 740H are the same as that for Alloy 617.
- 23 January 2018
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY18, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 1st quarter of FY18 modeling and simulation of the creep of thick section welds continued although some workscope from FY17 still needs to be completed. Four stress drop tests to determine the threshold stress for creep in Alloy 740H were carried out. One has finished and post-test analysis shows a threshold creep stress of about 67 MPa which is lower than that found in a previous program for Alloy 617 at the same temperature. Alloy 617 is not as creep resistant as Alloy 740H and the reason for the lower than expected threshold stress for Alloy 740H is being investigated further. Also analysis of the gamma prime particle size in an aging study closely follows the aging characteristics of gamma prime in Alloy 617. Further analysis of other aged materials will be carried out during the 2nd quarter of FY18 to confirm that the aging characteristic of Alloy 740H are the same as that for Alloy 617.
- 1 October 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 4th Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 4th quarter of FY17 modeling and simulation development of creep in nickel-based alloys was continued with a focus on incorporation of simulated alloy microstructures into the creep model. Additionally, the model was calibrated with experimental creep data from Alloy 617. Experimental data collection also continued with creep tests, stress drop tests and characterization of alloy microstructures.
- 1 October 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 4th Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the 4th quarter of FY17 modeling and simulation development of creep in nickel-based alloys was continued with a focus on incorporation of simulated alloy microstructures into the creep model. Additionally, the model was calibrated with experimental creep data from Alloy 617. Experimental data collection also continued with creep tests, stress drop tests and characterization of alloy microstructures.
- 1 April 2017
- Published by Office of Scientific and Technical Information (OSTI)
Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the second quarter of FY17, research efforts have been focused on modeling and simulation of the creep behavior of welds in Alloy 740H. Additionally, welded material has been sent to a commercial vendor to make creep specimen with cross-weld orientation as well as creep specimens consisting of all weld metal to evaluate the creep behavior of the different zones in and around the weld. Creep testing and aging of welds continued to evaluate microstructure evolution and the creep behavior as a function of aging time.
- 1 April 2017
- Published by Office of Scientific and Technical Information (OSTI)
Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the second quarter of FY17, research efforts have been focused on modeling and simulation of the creep behavior of welds in Alloy 740H. Additionally, welded material has been sent to a commercial vendor to make creep specimen with cross-weld orientation as well as creep specimens consisting of all weld metal to evaluate the creep behavior of the different zones in and around the weld. Creep testing and aging of welds continued to evaluate microstructure evolution and the creep behavior as a function of aging time.
- 1 January 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY17, research has focused on: 1. Generation of synthetic microstructures of welds 2. Aging of gamma prime 3. Short term creep tests 4. Preparation for stress drop tests to determine the threshold stress.
- 1 January 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY17, research has focused on: 1. Generation of synthetic microstructures of welds 2. Aging of gamma prime 3. Short term creep tests 4. Preparation for stress drop tests to determine the threshold stress.
- 1 January 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY17, research has focused on: 1. Generation of synthetic microstructures of welds 2. Aging of gamma prime 3. Short term creep tests 4. Preparation for stress drop tests to determine the threshold stress.
- 1 January 2017
- Published by Office of Scientific and Technical Information (OSTI)
Quarterly Management Document – FY17, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications
During the first quarter of FY17, research has focused on: 1. Generation of synthetic microstructures of welds 2. Aging of gamma prime 3. Short term creep tests 4. Preparation for stress drop tests to determine the threshold stress.