Moad Kissai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Moad Kissai has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Xavier Mouton
Groupe Renault
4 shared publications - Adriana Tapus
Institute Polytechnique de Paris
3 shared publications Bruno Monsuez
ENSTA ParisTech, France
3 shared publicationsDidier Martinez
Renault, France
3 shared publications- Adriana Tapus
ENSTA-ParisTech
1 shared publication - Bruno Monsuez
Autonomous Systems and Robotics Lab, Computer Science and System Engineering Department (U2IS), École Nationale Supérieure de Techniques Avancées (ENSTA ParisTech), Institut Polytechnique de Paris (IP Paris), 828 Boulevard des Maréchaux, 91120 Palaiseau, France
1 shared publication
Latest Publications
- Open Access
- 8 July 2020
- Published by SAE International in SAE International Journal of Connected and Automated Vehicles
- Vol. 03 (2) , 85-101
Optimal Coordination of Chassis Systems in Simultaneous Operations
Many research projects are focusing on automated vehicles and reinventing the automotive industry. New technologies are introduced, and the pillars of the ground vehicle are revisited and new challenges appeared. This article focuses on the chassis systems and their control strategies. While assistance strategies use to manage specific operations, autonomous vehicles need to handle simultaneous operations. Optimal solutions for systems coordination are discussed in this article. Robust control synthesis and optimization-based control allocation algorithms are adopted. Results show that the more we get closer to fully autonomous driving where an important number of embedded systems are needed, the more optimal coordination strategies are relevant. These strategies should be considered in the upcoming automotive industrial standards.
- 8 July 2020
- Published by SAE International in SAE International Journal of Connected and Automated Vehicles
- Vol. 03 (2) , 85-101
Open AccessOptimal Coordination of Chassis Systems in Simultaneous Operations
Many research projects are focusing on automated vehicles and reinventing the automotive industry. New technologies are introduced, and the pillars of the ground vehicle are revisited and new challenges appeared. This article focuses on the chassis systems and their control strategies. While assistance strategies use to manage specific operations, autonomous vehicles need to handle simultaneous operations. Optimal solutions for systems coordination are discussed in this article. Robust control synthesis and optimization-based control allocation algorithms are adopted. Results show that the more we get closer to fully autonomous driving where an important number of embedded systems are needed, the more optimal coordination strategies are relevant. These strategies should be considered in the upcoming automotive industrial standards.
- Open Access
- 14 April 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Optimal Yaw Rate Control for Over-Actuated Vehicles
As we are heading towards autonomous vehicles, additional driver assistance systems are being added. The vehicle motion is automated step by step to ensure passengers’ safety and comfort, while still preserving vehicle performance. However, simultaneous activations of concurrent systems may conflict, and non-suitable behavior may emerge. Our research work consists in proving that with the right coordination approach, simultaneous operation of different systems improve the vehicle’s performance and avoid the emergence of unwanted conflicts. To prove this, we gathered different control architectures implemented in commercial passenger cars, and we compared them with our control architecture using a unified reference vehicle model. The high-fidelity vehicle model is developed in Simcenter Amesim in a modular and extensible manner. This enables adding systems in a plug-and-play way. Not only different control architectures can be tested on the same vehicle, but also different systems combinations can be evaluated. In this research, the vehicle can steer at the front and at the rear, and each wheel can be braked independently. Each of the actuators concerned can influence the vehicle’s yaw rate leading in some cases in system conflicts. More complex control strategies are then implemented in Matlab/Simulink, and co-simulations are carried between both softwares in order to provide realistic results. It has been shown that optimal control allocation algorithms are more suitable to coordinate systems in an over-actuated vehicle. Moreover, if the optimization objectives are well formalized, performance, safety and comfort can be improved since the vehicle can benefit from the systems’ synergies.
- 14 April 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Open AccessOptimal Yaw Rate Control for Over-Actuated Vehicles
As we are heading towards autonomous vehicles, additional driver assistance systems are being added. The vehicle motion is automated step by step to ensure passengers’ safety and comfort, while still preserving vehicle performance. However, simultaneous activations of concurrent systems may conflict, and non-suitable behavior may emerge. Our research work consists in proving that with the right coordination approach, simultaneous operation of different systems improve the vehicle’s performance and avoid the emergence of unwanted conflicts. To prove this, we gathered different control architectures implemented in commercial passenger cars, and we compared them with our control architecture using a unified reference vehicle model. The high-fidelity vehicle model is developed in Simcenter Amesim in a modular and extensible manner. This enables adding systems in a plug-and-play way. Not only different control architectures can be tested on the same vehicle, but also different systems combinations can be evaluated. In this research, the vehicle can steer at the front and at the rear, and each wheel can be braked independently. Each of the actuators concerned can influence the vehicle’s yaw rate leading in some cases in system conflicts. More complex control strategies are then implemented in Matlab/Simulink, and co-simulations are carried between both softwares in order to provide realistic results. It has been shown that optimal control allocation algorithms are more suitable to coordinate systems in an over-actuated vehicle. Moreover, if the optimization objectives are well formalized, performance, safety and comfort can be improved since the vehicle can benefit from the systems’ synergies.
- Open Access
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 822-829
Robust Control for Over-Actuated Vehicles
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 822-829
Open AccessRobust Control for Over-Actuated Vehicles
- Open Access
Adaptive Robust Vehicle Motion Control for Future Over-Actuated Vehicles
Many challenges still need to be overcome in the context of autonomous vehicles. These vehicles would be over-actuated and are expected to perform coupled maneuvers. In this paper, we first discuss the development of a global coupled vehicle model, and then we outline the control strategy that we believe should be applied in the context of over-actuated vehicles. A gain-scheduled controller and an optimization-based Control Allocation algorithms are proposed. High-fidelity co-simulation results show the efficiency of the proposed control logic and the new possibilities that could offer. We expect that both car manufacturers and equipment suppliers would join forces to develop and standardize the proposed control architecture for future passenger cars.Open AccessAdaptive Robust Vehicle Motion Control for Future Over-Actuated Vehicles
Many challenges still need to be overcome in the context of autonomous vehicles. These vehicles would be over-actuated and are expected to perform coupled maneuvers. In this paper, we first discuss the development of a global coupled vehicle model, and then we outline the control strategy that we believe should be applied in the context of over-actuated vehicles. A gain-scheduled controller and an optimization-based Control Allocation algorithms are proposed. High-fidelity co-simulation results show the efficiency of the proposed control logic and the new possibilities that could offer. We expect that both car manufacturers and equipment suppliers would join forces to develop and standardize the proposed control architecture for future passenger cars.