P. A. Kozlov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
P. A. Kozlov has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Andrey Belyakov
Belgorod National Research University , Belgorod , 308015 , Russia
2 shared publications I. A. Shchenkova
OAO NPO TsNIITMASh
2 shared publications- Irina Fedorova
Belgorod State University
2 shared publications Izabella Schenkova
Central Research Institute for Machine-Building Technology
2 shared publicationsRustam Kaibyshev
Belgorod State University
2 shared publicationsV. N. Skorobogatykh
OAO NPO TsNIITMASh
2 shared publications
Latest Publications
- 1 October 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 615, 153-163
Laves-phase precipitates in a low-carbon 9% Cr martensitic steel during aging and creep at 923 K
- 1 October 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 615, 153-163
Laves-phase precipitates in a low-carbon 9% Cr martensitic steel during aging and creep at 923 K
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 1839-1844
Effect of Long-Term Creep on Microstructure of a 9% Cr Heat Resistant Steel
The effect of long-term creep at 600°C under 137 MPa on the microstructure of a P92-type steel was investigated. The microstructure after tempering consisted of laths with an average thickness of 400 nm. Dispersion of secondary phases consists of M23C6 carbides with an average size of 85 nm located mainly on lath, block and prior austenite boundaries and MX carbonitrides with average size of 31 nm homogeniously distributed throughout. Creep with duration of 40738 hours led to coarsening of M23C6 carbides up to 182 nm. Precipitation of Laves phase with an average size of 290 nm took place in both grip and gauge portions of ruptured specimen. Vanadium-rich MX particles were replaced by particles of Z-phase with sizes of 97 and 48 nm after long-term creep and aging, respectively. The average misorientation of the lath boundaries was approximately 2° and scarcely varied during creep, while the mean lath thickness increased to 890 nm in gauge section of ruptured specimen and remained essentially unchanged in the grip section. Dislocation density decreased slightly under long-range aging and creep.
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 1839-1844
Effect of Long-Term Creep on Microstructure of a 9% Cr Heat Resistant Steel
The effect of long-term creep at 600°C under 137 MPa on the microstructure of a P92-type steel was investigated. The microstructure after tempering consisted of laths with an average thickness of 400 nm. Dispersion of secondary phases consists of M23C6 carbides with an average size of 85 nm located mainly on lath, block and prior austenite boundaries and MX carbonitrides with average size of 31 nm homogeniously distributed throughout. Creep with duration of 40738 hours led to coarsening of M23C6 carbides up to 182 nm. Precipitation of Laves phase with an average size of 290 nm took place in both grip and gauge portions of ruptured specimen. Vanadium-rich MX particles were replaced by particles of Z-phase with sizes of 97 and 48 nm after long-term creep and aging, respectively. The average misorientation of the lath boundaries was approximately 2° and scarcely varied during creep, while the mean lath thickness increased to 890 nm in gauge section of ruptured specimen and remained essentially unchanged in the grip section. Dislocation density decreased slightly under long-range aging and creep.
- 7 May 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 922, 155-160
Evolution of Laves-Phase Particles in a Low Carbon 9%Cr Martensitic Steel during Creep at 650°C
The evolution of microstructure in low carbon heat resistant steel of P92-type modified with 3%Co was examined during creep tests at 923K for 500, 1500, 6000 and 16000 hours. After tempering at 1023K (750°C), the steel was composed of martensite lath structure with numerous precipitates of MX-type carbonitrides and rare M23C6-type carbides. The structural changes during creep tests are characterized by an increase in the sizes of laths and second phase particles. Moreover, the Fe2W Laves-phase precipitates during long-term creep. The Laves-phase particles grow accordingly to power-law relationship of creep time.
- 7 May 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 922, 155-160
Evolution of Laves-Phase Particles in a Low Carbon 9%Cr Martensitic Steel during Creep at 650°C
The evolution of microstructure in low carbon heat resistant steel of P92-type modified with 3%Co was examined during creep tests at 923K for 500, 1500, 6000 and 16000 hours. After tempering at 1023K (750°C), the steel was composed of martensite lath structure with numerous precipitates of MX-type carbonitrides and rare M23C6-type carbides. The structural changes during creep tests are characterized by an increase in the sizes of laths and second phase particles. Moreover, the Fe2W Laves-phase precipitates during long-term creep. The Laves-phase particles grow accordingly to power-law relationship of creep time.
- 1 June 2012
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2012 (6) , 527-530
Influence of heat treatment on the structure and hardness of 9% chromium steel
The results of studying the influence of the heat treatment conditions on the structure and properties of new nanostructured steel with 8–10% Cr designed for heat power units with supercritical parameters are presented.
- 1 June 2012
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2012 (6) , 527-530
Influence of heat treatment on the structure and hardness of 9% chromium steel
The results of studying the influence of the heat treatment conditions on the structure and properties of new nanostructured steel with 8–10% Cr designed for heat power units with supercritical parameters are presented.
- 3 January 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 706-709, 865-870
Evolution of Intermetallic Phase Fe2(W, Mo) in 9% Cr Steel during Creep Rupture Tests at 650°C
Our report deals with investigation of evolution of AB2 phase in three melts of new 9% Cr heat resistant steel with different chemical compositions during creep rupture tests at 650°C in the course of 10000 hours. For each sample the following research procedure was applied: (i) identification of all second phases precipitations using differential X-ray analysis method; (ii) study of spatial distribution of second phases using scanning electron microscope and transmission electron microscope; (iii) numerical investigation of mass fraction and average size of AB2 particles using developed algorithm of statistical processing of images from electron microscope. It was found that for all melts mass fraction-time curve has global maximum and the rate of subsequent reduction of mass fraction depends on content of alloying elements.
- 3 January 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 706-709, 865-870
Evolution of Intermetallic Phase Fe2(W, Mo) in 9% Cr Steel during Creep Rupture Tests at 650°C
Our report deals with investigation of evolution of AB2 phase in three melts of new 9% Cr heat resistant steel with different chemical compositions during creep rupture tests at 650°C in the course of 10000 hours. For each sample the following research procedure was applied: (i) identification of all second phases precipitations using differential X-ray analysis method; (ii) study of spatial distribution of second phases using scanning electron microscope and transmission electron microscope; (iii) numerical investigation of mass fraction and average size of AB2 particles using developed algorithm of statistical processing of images from electron microscope. It was found that for all melts mass fraction-time curve has global maximum and the rate of subsequent reduction of mass fraction depends on content of alloying elements.
- 1 December 2011
- Published by Taylor & Francis in International Heat Treatment and Surface Engineering
- Vol. 5 (4) , 161-164
Investigation of phase composition of high temperature chromium steels and chromonitriding process in austenitic alloys
- 1 December 2011
- Published by Taylor & Francis in International Heat Treatment and Surface Engineering
- Vol. 5 (4) , 161-164
Investigation of phase composition of high temperature chromium steels and chromonitriding process in austenitic alloys
- 1 March 2011
- Published by Allerton Press in Steel in Translation
- Vol. 41 (3) , 211-214
Influence of carbon on the structure and properties of heat-resistant 9% chrome steel
- 1 March 2011
- Published by Allerton Press in Steel in Translation
- Vol. 41 (3) , 211-214
Influence of carbon on the structure and properties of heat-resistant 9% chrome steel
- 1 May 1981
- No. 5,p. 62-3
[Planning the recovery of silver in a polyclinic x-ray office].