Irina Fedorova
Research Subjects
Irina Fedorova has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Andrey Belyakov
Belgorod National Research University , Belgorod , 308015 , Russia
6 shared publications R. Kaibyshev
3 shared publicationsRustam Kaibyshev
Belgorod State University
3 shared publications- Fang Liu
Chalmers University of Technology
2 shared publications - John Hald
Department of Mechanical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby, Denmark
2 shared publications - P. A. Kozlov
Central Research Institute for Machine-Building Technology
2 shared publications
Latest Publications
- 30 January 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (2) , 462-469
Analyzing Boron in 9–12% Chromium Steels Using Atom Probe Tomography
Small additions of boron can remarkably improve the long-term creep resistance of 9–12% Cr steels. The improvement has been attributed to boron segregation to grain boundaries during quenching, and subsequent boron incorporation into certain families of precipitates during tempering. However, the detailed mechanisms are not yet fully understood. Atom probe tomography (APT) is an excellent technique for gaining insights into boron distribution, however, in order to acquire accurate analysis of boron in 9–12% Cr steels using APT, there are several key challenges. In order to better understand and address these challenges, we developed a novel method for site-specific APT specimen preparation, which enables convenient preparation of specimens containing specifically selected grain boundaries positioned approximately perpendicular to the axis of the APT tip. Additionally, when analyzing boron at boundaries and in carbides (as diluted solute) and borides, a widening of the profile of boron distribution compared to other elements was repeatedly observed. This phenomenon is particularly analyzed and discussed in light of the evaporation field of different elements. Finally, the possible effects of detector dead-time on quantitative analysis of boron in metal borides are discussed. A simple method using10B correction was used to obtain good quantification.
- 30 January 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (2) , 462-469
Analyzing Boron in 9–12% Chromium Steels Using Atom Probe Tomography
Small additions of boron can remarkably improve the long-term creep resistance of 9–12% Cr steels. The improvement has been attributed to boron segregation to grain boundaries during quenching, and subsequent boron incorporation into certain families of precipitates during tempering. However, the detailed mechanisms are not yet fully understood. Atom probe tomography (APT) is an excellent technique for gaining insights into boron distribution, however, in order to acquire accurate analysis of boron in 9–12% Cr steels using APT, there are several key challenges. In order to better understand and address these challenges, we developed a novel method for site-specific APT specimen preparation, which enables convenient preparation of specimens containing specifically selected grain boundaries positioned approximately perpendicular to the axis of the APT tip. Additionally, when analyzing boron at boundaries and in carbides (as diluted solute) and borides, a widening of the profile of boron distribution compared to other elements was repeatedly observed. This phenomenon is particularly analyzed and discussed in light of the evaporation field of different elements. Finally, the possible effects of detector dead-time on quantitative analysis of boron in metal borides are discussed. A simple method using10B correction was used to obtain good quantification.
- 1 November 2018
- Published by Elsevier in Scripta Materialia
- Vol. 156, 124-128
Fine (Cr,Fe)2B borides on grain boundaries in a 10Cr–0.01B martensitic steel
- 1 November 2018
- Published by Elsevier in Scripta Materialia
- Vol. 156, 124-128
Fine (Cr,Fe)2B borides on grain boundaries in a 10Cr–0.01B martensitic steel
- 1 April 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 662, 443-455
Tempering behavior of a low nitrogen boron-added 9%Cr steel
- 1 April 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 662, 443-455
Tempering behavior of a low nitrogen boron-added 9%Cr steel
- 1 October 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 615, 153-163
Laves-phase precipitates in a low-carbon 9% Cr martensitic steel during aging and creep at 923 K
- 1 October 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 615, 153-163
Laves-phase precipitates in a low-carbon 9% Cr martensitic steel during aging and creep at 923 K
- 1 June 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 606, 380-389
Grain refinement in a Cu–Cr–Zr alloy during multidirectional forging
- 1 June 2014
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 606, 380-389
Grain refinement in a Cu–Cr–Zr alloy during multidirectional forging
- 7 May 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 922, 155-160
Evolution of Laves-Phase Particles in a Low Carbon 9%Cr Martensitic Steel during Creep at 650°C
The evolution of microstructure in low carbon heat resistant steel of P92-type modified with 3%Co was examined during creep tests at 923K for 500, 1500, 6000 and 16000 hours. After tempering at 1023K (750°C), the steel was composed of martensite lath structure with numerous precipitates of MX-type carbonitrides and rare M23C6-type carbides. The structural changes during creep tests are characterized by an increase in the sizes of laths and second phase particles. Moreover, the Fe2W Laves-phase precipitates during long-term creep. The Laves-phase particles grow accordingly to power-law relationship of creep time.
- 7 May 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 922, 155-160
Evolution of Laves-Phase Particles in a Low Carbon 9%Cr Martensitic Steel during Creep at 650°C
The evolution of microstructure in low carbon heat resistant steel of P92-type modified with 3%Co was examined during creep tests at 923K for 500, 1500, 6000 and 16000 hours. After tempering at 1023K (750°C), the steel was composed of martensite lath structure with numerous precipitates of MX-type carbonitrides and rare M23C6-type carbides. The structural changes during creep tests are characterized by an increase in the sizes of laths and second phase particles. Moreover, the Fe2W Laves-phase precipitates during long-term creep. The Laves-phase particles grow accordingly to power-law relationship of creep time.
- 25 April 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (S1) , 128-135
Microstructure Evolution in an Advanced 9 pct Cr Martensitic Steel during Creep at 923 K (650 °C)
- 25 April 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (S1) , 128-135
Microstructure Evolution in an Advanced 9 pct Cr Martensitic Steel during Creep at 923 K (650 °C)
- 29 November 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 409, 672-677
Microstructure and Deformation Behavior of a Hot Forged 9%Cr Creep Resistant Steel
The tempered microstructure and the creep behaviour were studied in an ultra low carbon 9%Cr martensitic creep resistant steel. The starting material was forged at 1050°C followed by air cooling and then tempered at a temperature of 750°C for 3 hours. This treatment resulted in the mean transverse lath size of about 240 nm; the dislocation density in lath interiors comprised 4 × 1014 m-2. The tempered martensite lath structure (TMLS) is characterised by homogeneous precipitation of numerous MX-type carbonitrides and a small amount of relatively coarse M23C6–type carbides. Three kinds of MX carbonitrides were observed in the tempered lath martensite structure. Those were plate-shaped particles with longitudinal size of about 15 nm and thickness of 3 nm; round-shaped particles of about 10 nm in diameter; and relatively large almost equiaxed particles with mean size of about 90 nm. The large MX particles were resulted from incomplete dissolution of such carbonitrides at 1050°C, while the nanoscale particles homogeneously precipitated during the tempering. The creep tests conducted at 650°C showed that the studied steel demonstrated superior creep resistance. Namely, the rupture time was about an order as long as that for P92-type creep resistant steel.
- 29 November 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 409, 672-677
Microstructure and Deformation Behavior of a Hot Forged 9%Cr Creep Resistant Steel
The tempered microstructure and the creep behaviour were studied in an ultra low carbon 9%Cr martensitic creep resistant steel. The starting material was forged at 1050°C followed by air cooling and then tempered at a temperature of 750°C for 3 hours. This treatment resulted in the mean transverse lath size of about 240 nm; the dislocation density in lath interiors comprised 4 × 1014 m-2. The tempered martensite lath structure (TMLS) is characterised by homogeneous precipitation of numerous MX-type carbonitrides and a small amount of relatively coarse M23C6–type carbides. Three kinds of MX carbonitrides were observed in the tempered lath martensite structure. Those were plate-shaped particles with longitudinal size of about 15 nm and thickness of 3 nm; round-shaped particles of about 10 nm in diameter; and relatively large almost equiaxed particles with mean size of about 90 nm. The large MX particles were resulted from incomplete dissolution of such carbonitrides at 1050°C, while the nanoscale particles homogeneously precipitated during the tempering. The creep tests conducted at 650°C showed that the studied steel demonstrated superior creep resistance. Namely, the rupture time was about an order as long as that for P92-type creep resistant steel.