Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Angel Serrano has a total of 84 co-authors. Here are the top co-authors by number of shared publications:

  • Juan Francisco Rodriguez

    Chemical Engineering Department, University of Castilla-La Mancha, Institute of Chemical and Environmental Technology, ITQUIMA, Avda. Camilo José Cela s/n, 13004 Ciudad Real, Spain

    12 shared publications
  • Ana Maria Borreguero

    Chemical Engineering Department, University of Castilla-La Mancha, Institute of Chemical and Environmental Technology, ITQUIMA, Avda. Camilo José Cela s/n, 13004 Ciudad Real, Spain

    9 shared publications
  • Manuel Carmona

    Department of Chemical Engineering, Institute of Chemical and Environmental Technology, University of Castilla-La Mancha, Avda. De Camilo José Cela 1, 13005 Ciudad Real, Spain

    9 shared publications
  • Jean-Luc Dauvergne

    Centre for Cooperative Research on Alternative Energies (CIC energiGUNE), Basque Research and Technology Alliance (BRTA), Alava Technology Park, Albert Einstein 48, 01510 Vitoria-Gasteiz, Spain

    7 shared publications
  • Stefania Doppiu

    Centre for Cooperative Research on Alternative Energies (CIC energiGUNE), Basque Research and Technology Alliance (BRTA), Alava Technology Park, Albert Einstein 48, 01510 Vitoria-Gasteiz, Spain

    6 shared publications
  • Elena Palomo del Barrio

    Centre for Cooperative Research on Alternative Energies (CIC energiGUNE), Basque Research and Technology Alliance (BRTA), Alava Technology Park, 01510 Vitoria-Gasteiz, Spain

    5 shared publications

Latest Publications

  • Experimental and numerical study of a novel cost-effective macro-encapsulated solid-solid PCM for solar process heat thermal energy storage

    by Daniel Bielsa, Peru Arribalzaga, Imanol Martinez, Mehdi Hashemi-Tilehnoee, Ivan Torrano, Angel Serrano, Elena Palomo del Barrio


  • Open Access

    Improved Thermophysical and Mechanical Properties in LiNaSO4 Composites for Thermal Energy Storage

    by Maria Taeño, Ariba Adnan, Cristina Luengo, Ángel Serrano, Jean-Luc Dauvergne, Paola Crocomo, Ali Huerta, Stefania Doppiu, Elena Palomo del Barrio

    Solid-solid phase-change materials have great potential for developing compact and low-cost thermal storage systems. The solid-state nature of these materials enables the design of systems analogous to those based on natural rocks but with an extraordinarily higher energy density. In this scenario, the evaluation and improvement of the mechanical and thermophysical properties of these solid-solid PCMs are key to exploiting their full potential. In this study, LiNaSO4-based composites, comprising porous MgO and expanded graphite (EG) as the dispersed phases and LiNaSO4 as the matrix, have been prepared with the aim of enhancing the thermophysical and mechanical properties of LiNaSO4. The characteristic structure of MgO and the high degree of crystallinity of the EG600 confer on the LiNaSO4 sample mechanical stability, which leads to an increase in the Young’s modulus (almost three times higher) compared to the pure LiNaSO4 sample. These materials are proposed as a suitable candidate for thermal energy storage applications at high temperatures (400–550 °C). The addition of 5 wt.% of MgO or 5% of EG had a minor influence on the solid-solid phase change temperature and enthalpy; however, other thermal properties such as thermal conductivity or specific heat capacity were increased, extending the scope of PCMs use.


  • Open Access

    Effect of processing on thermal properties of pentaglycerine-based solid-solid phase change materials

    by Ángel Serrano, Sergio Santos, Jean-Luc Dauvergne, Juan Miguel López del Amo, Mikel Durán, Maria Taeño, Stefania Doppiu, Elena Palomo Del Barrio


  • Cement Based Materials with PCM and Reduced Graphene Oxide for Thermal Insulation for Buildings

    by Edurne Erkizia, Christina Strunz, Jean-Luc Dauvergne, Guido Goracci, Ignacio Peralta, Ángel Serrano, Amaya Ortega, Beatriz Alonso, Francesca Zanoni, Michael Düngfelder, et al.


  • Open Access

    Effect of Foaming Formulation and Operating Pressure on Thermoregulating Polyurethane Foams

    by Angel Serrano, Ana M. Borreguero, Juan Catalá, Juan F. Rodríguez, Manuel Carmona

    The synthesis of rigid polyurethane (RPU) foams containing thermoregulatory microcapsules has been carried out under reduced pressure conditions with a new foaming formulation to reduce the final composite densities. These optimized RPU foams were able to overpass the drawbacks exhibited by the previous composites over the studied temperature range, working as insulating and thermal energy storage materials. The change in the formulation allowed to decrease the final foam density and enhance their mechanical strength. The effect of the operating pressure (atmospheric, 800 mbar, and 700 mbar) and microcapsules content (up to 30 wt%) on the physical, mechanical, and thermal PU foam properties was studied. The reduction of the pressure from atmospheric to 800 mbar did not have any effect on the cell size, strut thickness, and compression strength 10% of deformation, the Young modulus being even higher at 800 mbar. Nevertheless, a strong impact on the microstructure and mechanical properties was observed for the foam composites obtained at 700 mbar. A deleterious impact on the RPU foams thermal conductivity was observed when using low-pressure conditions. Thermal analyses showed that a composite able to work as heat accumulator and thermal insulation both at transient and at steady state was achieved.


  • Sustainable lignin‐based polyols as promising thermal energy storage materials

    by Jonatan Perez‐Arce, Angel Serrano, Jean‐Luc Dauvergne, Ander Centeno‐Pedrazo, Soraya Prieto‐Fernandez, Elena Palomo Del Barrio, Eduardo J. Garcia‐Suarez

    Six lignin‐based polyols (LBPs) have been prepared by cationic ring opening polymerization of an oxirane in the presence of an organosolv lignin in tetrahydrofuran (THF) as reaction media and co‐monomer. The prepared LBPs have been characterized and tested for the first time as phase change materials (PCMs) for thermal energy storage (TES) at low temperature. It was found a strong influence of the LBPs composition on their performance to storage thermal energy. Thus, LBPs with higher THF wt% content and lower oxirane/THF mass ratio exhibit the highest latent heats. Furthermore, a clear inversely proportional trend between the oxirane/THF mass ratio and the melting temperatures of the prepared LBPs was noticed. Among the prepared LBPs, the highest obtained latent heat was 53.7 J/g demonstrating the potential application of lignin as feedstock for PCMs preparation. To the best of our knowledge, this is the first time that a biomass derived PCM based on lignin has been studied and considered for TES applications at low temperature. LBPs show energetic solid–liquid transitions that point out their promising potential as bio‐PCMs. This work paves the way to introduce new bio‐based PCMs from lignin in TES systems, for example, in a more sustainable construction sector.


  • Open Access

    Thermal and Mechanical Behavior of Elastomers Incorporated with Thermoregulating Microcapsules

    by Ana M. Borreguero, Irene Izarra, Ignacio Garrido, Patrycja J. Trzebiatowska, Janusz Datta, Ángel Serrano, Juan F. Rodríguez, Manuel Carmona

    Polyurethane (PU) is one of the principal polymers in the global plastic market thanks to its versatility and continuous improvement. In this work, PU elastomeric materials having thermoregulating properties through the incorporation of microcapsules (mSD-(LDPE·EVA-RT27)) from low-density polyethylene and vinyl acetate containing paraffin®RT27 as PCM were produced. Elastomers were synthesized while varying the molar ratio [NCO]/[OH] between 1.05 and 1.1 and the microcapsule (MC) content from 0.0 to 20.0 wt.%. The successful synthesis of the PUs was confirmed by IR analyses. All the synthesized elastomers presented a structure formed by a net of spherical microparticles and with a minimum particle size for those with 10 wt.% MC. The density and tensile strength decreased with the MC content, probably due to worse distribution into the matrix. Elastomer E-1.05 exhibited better structural and stability properties for MC contents up to 15 wt.%, whereas E-1.1, containing 20 wt.% MC, revealed mechanical and thermal synergy effects, demonstrating good structural stability and the largest latent heat. Hence, elastomers having a large latent heat (8.7 J/g) can be produced by using a molar ratio [NCO]/[OH] of 1.1 and containing 20 wt.% mSD-(LDPE·EVA-RT27).


  • Open Access

    Li4(OH)3Br-Based Shape Stabilized Composites for High-Temperature TES Applications: Selection of the Most Convenient Supporting Material

    by Imane Mahroug, Stefania Doppiu, Jean-Luc Dauvergne, Angel Serrano, Elena Palomo del Barrio

    Peritectic compound Li4(OH)3Br has been recently proposed as phase change material (PCM) for thermal energy storage (TES) applications at approx. 300 °C Compared to competitor PCM materials (e.g., sodium nitrate), the main assets of this compound are high volumetric latent heat storage capacity (>140 kWh/m3) and very low volume changes (4(OH)3Br during the formation of the melt and after its complete melting, avoiding any leakage and thus obtaining a composite apparently always in the solid state during the charge and discharge of the TES material. Micro-nanoparticles of MgO, Fe2O3, CuO, SiO2 and Al2O3 have been considered as candidate supporting materials combined with the cold-compression route for shape-stabilized composites preparation. The work carried out allowed for the identification of the most promising composite based on MgO nanoparticles through a deep experimental analysis and characterization, including chemical compatibility tests, anti-leakage performance evaluation, structural and thermodynamic properties analysis and preliminary cycling stability study.


  • Open Access

    Diffusion of Shape Stabilized PEG-SiO2 as a Driver for Producing Thermoregulating Facing Bricks

    by Angel Serrano, Ana M. Borreguero, Isabel Iglesias, Anselmo Acosta, Juan F. Rodríguez, Manuel Carmona

    A novel form-stable phase-change material (PCM) based on facing bricks was developed by incorporating thermoregulating PEG-SiO2, synthetized by sol-gel method and based on polyethylene glycol as phase-change material and silica as stabilizer compound. The PEG-SiO2 in its liquid form (sol) is firstly adsorbed inside the porous brick and lastly stabilized (gel) by controlling its gelation time, obtaining form-stable PCMs with PEG-SiO2 contents within 15–110 wt.%. Kinetic adsorption curves of the sol into bricks having different porosities as well as maximum adsorption capacities were obtained. The effective diffusion coefficients (Deff) were estimated by means of Fick’s second law, it being possible to predict the adsorption of sol PEG-SiO2 by the brick as function of its porosity and the free diffusion coefficient. Finally, form-stable PCMs demonstrated an improvement in their thermal energy storage capacity (up to 338%), these materials being capable of buffering the indoor temperature during an entire operational day