MBMaksym Balaka

Maksym Balaka

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Maksym Balaka has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ЕКСПЕРИМЕНТАЛЬНІ ДОСЛІДЖЕННЯ ПРОЦЕСУ РІЗАННЯ ҐРУНТУ НАКОНЕЧНИКОМ З ДИНАМІЧНОЮ РІЖУЧОЮ КРОМКОЮ

    by М.о. Пристайло, М.м. Балака, А.г. Поліщук, І.п. Гонта

    The experimental study results of the of soil cutting with dynamic cutting edge tip and the pneumatic accumulator are presented in the paper. Recent research and publications indicate increasing attention to improving the energy efficiency of earthmoving processes through adaptive and energy-storing working elements; however, existing theoretical models remain insufficiently accurate for predicting force interaction parameters in complex soil–tool systems. This creates the need for experimental verification and refinement of analytical approaches. The purpose of the study is to experimentally determine the cutting resistance force and to establish its dependence on the pressure level in the pneumatic accumulator. The main research methods include physical modeling using the paraffin-based soil analogue, strain-gauge measurements, and mathematical processing of experimental data with subsequent comparative analysis against theoretical predictions. The obtained results demonstrate the pronounced nonlinear dependence of cutting force on pressure, characterized by the U-shaped curve. It was found that the system exhibits an optimal pressure range, within which the minimum cutting resistance and the most energy-efficient operating regime are achieved. Outside this range, both low and excessive pressure levels lead to increased cutting resistance due to insufficient damping or excessive system rigidity. The comparison between experimental and theoretical results showed good agreement, with the deviation of up to 11%, confirming the adequacy of the proposed theoretical model. The results obtained can be used for the design and optimization of working elements of construction machinery aimed at reducing energy consumption and improving operational efficiency.

  • Open Access

    Overview of energy-efficient bulldozer blade designs

    by Oleksandr Diachenko, Maksym Balaka

    The comprehensive research of modern energy-efficient and adaptive designs of bulldozer blades used in transport construction, mining and special engineering works, are carried out in the paper. The geometric parameters of the blades, the regularities of the drag prism formation, the force interaction of the blade with the soil, as well as the influence of various profiles (S-blade, SU-blade, U-blade, Σ-blade, VPAT and DSAB) on cutting resistance, performance and specific energy consumption are considered. The research is based on the principles of soil mechanics, modeling of cutting forces, estimating the soil drag prism volume, determining the resistance to movement and calculating the technical performance of bulldozers with different types of blades. Particular attention is paid to innovative designs of Σ-blade and dual-stabilized angle blade, which provide a reduction in soil resistance by up to 15–28% and an increase in performance by up to 45% compared to blade traditional solutions. The results obtained confirm the effectiveness of profiled and adaptive blades by optimizing the geometry of the working surface and adjusting the cutting angle. Engineering recommendations are proposed for the implementation of adaptive systems in modern bulldozers in order to reduce fuel consumption, reduce the load on the transmission and increase the energy efficiency of the machines.

  • Open Access

    Improving the Niryo One robotic platform by the optimizing of the drive operating modes. Part II

    by Dmytro Mishchuk, Yevhen Mishchuk, Maksym Balaka, Дмитро Міщук, Євген Міщук

    The paper considers the issue of improving the Niryo One robotic platform by optimizing the operating modes of the manipulator drive. The relevance of the research is due to the need to increase the efficiency and accuracy of robotic systems in industrial and research applications. The second part of the study presents the devel-opment of a mathematical model of manipulator dynamics, which takes into account the design features and parameters of the Niryo One platform. Based on the constructed manipulator model, the manipulator motion trajectories were optimized using the sequential quadratic pro-gramming method (SLSQP — Sequential Least Squares Programming). Optimization was aim at minimizing energy consumption and task execu-tion time while adhering to constraints on the dynamic characteristics of the system.The proposed approach to determining optimal driving modes based on numerical methods of nonlinear programming. As optimization result of trajectories were obtain that provide a reduction in the load on the drives and an increase in the smoothness of movement compared to typical modes, that can be implemented in standard plat-form software. A comparative analysis of optimal and typical driving modes was conduct based on the criteria of energy efficiency and work dynam-ics.The results obtained can be used to modernize existing and develop new control algorithms for two-mass robotic systems, as well as to increase reliability and service life. Prospects for further research been related to the adaptation of the de-veloped method for manipulators with other kin-ematic schemes and under conditions of variable external loads.

  • Open Access

    Determination of rheological parameters for tire–road contact system

    by Maksym Balaka, Dmytro Mishchuk, Дмитро Міщук

    The efficiency and safety of modern wheeled vehicles significantly depend on the reliable interaction between pneumatic tires and the supporting road or soil surface under varying load conditions. This interaction is governed by a complex combination of elastic, viscous and plastic deformation processes, occurring both in the tire structure and in the contact layer of the supporting surface. Accurate description of these processes requires the development and application of advanced rheological models capable of reproducing the nonlinear and time-dependent behavior of tire materials. The analytical and experimental methodologies for determining the rheological parameters of pneumatic tires, including stiffness, deformation modulus, viscous resistance and internal friction characteristics are proposed in the paper. The methods are based on the analysis of static and dynamic deformation behavior, as well as on the spatial distribution of contact stresses in the tire–road interface. The approach allows for capturing the influence of varying load levels and inflation pressure on the tire’s mechanical response. The obtained rheological parameters provide a foundation for constructing numerical models of the tire–road contact system, enabling accurate prediction of contact stresses, deformation patterns, and dynamic loading during vehicle operation. The proposed methodologies reduce experimental complexity and improve parameter accuracy, offering practical value for tire design, optimization of vehicle dynamics and transport engineering applications.

  • Open Access

    Optimization of soil cutting process by ripper tip with dynamic cutting edge

    by Mykola Prystailo, Maksym Balaka, Andrii Polischuk, Andrii Kozak, Ihor Honta

    The mechanical processes of interaction between the ripper tip with the dynamic cutting edge on the pneumatic accumulator and the soil massif are investigated in the paper. Rheological models of the soil are considered, describing its elastic and viscoelastic properties, as well as the regularities of deformation under the action of the working element. The movement speed of the ripper tip, the dynamics of changes in cutting force, and the formation nature of the compressed zone for different soil categories are investigated based on the combination of analytical methods and experimental tests. The results obtained allowed us to establish the influence regularities of the ripper tip parameters on power loads, energy consumption and stability of the technological process. It is shown that the ripper tip use with the dynamic cutting edge on the pneumatic accumulator contributes to the decrease in peak and average loads, the decrease in friction forces and vibration oscillations. This leads to an increase in energy efficiency, the decrease in dynamic shocks and the increase in the resource of the working element. It’s found that the maximum effect is achieved during the development of light and medium-density soils, where the greatest reduction in cutting force and the highest process stability are observed. The energy effect is less pronounced for strong soils, but the positive effect on load stabilization is preserved. The practical significance of the results obtained lies in the possibility of improving the designs of ripper tips, substantiating rational modes of their operation. It also aims at increasing the efficiency of technological processes during preparatory works in transport and industrial construction, mining and the agricultural sector.

  • Open Access

    Feasibility study of reach stacker model choice

    by Serhii Lysak, Maksym Balaka, Vladyslav Riepin, Volodymyr Yahodynets, Artem Matsybura, Сергій Лисак, Владислав Рєпін, Володимир Ягодинець, Артем Мацибура

    The paper considers an approach to choosing the optimal reach stacker model for container terminals based on engineering-and-econo­mic performance. The technical characteristics of models from leading global manufacturers of handling machinery are analyzed. A methodology to determine the technical and operational productivity of reach stackers in the absence of complete data from the manufacturer is proposed. Five key efficiency criteria are identified: specific power, energy saturation, economic efficiency, cost power and cost mass. The most effective model choice is justified based on the ranking of models for each criterion and the calculation of the final score. The study results can be applied when forming technical requirements and specifications for the purchase of handling machinery. They also serve as an analytical basis for making informed mana­gement decisions in the field of logistics infrastructure development, and cargo terminals and ports modernization.

  • Features of the Dynamic Interaction Between the Elastically Deformed Working Body of a Ripper-Pick and the Soil

    by Kostiantyn Pochka, Mykola Prystailo, Maksym Delembovskyi, Maksym Balaka, Yurii Maksymiuk, Andrii Polishchuk


  • Open Access

    Methods of conducting a bench-scale experimental study with a spatially oriented knife of a bulldozer blade

    by Volodymyr Rashkivskyi, Mykola Prystailo, Bohdan Fedyshyn, Maksym Balaka

    The paper considers the assessment of the interaction of a spatially oriented knife of a bulldozer blade with the working environment, which was carried out on the basis of a one-factor experiment using high-tech measuring and recording equipment, which allowed to quickly obtain accurate results from the primary data. Oscillogram processing consisted of determining the average maximum ordinate of the cutting force P and finding its value. Thanks to the use of the designed and developed high-precision control system for feeding and transverse movement of the working body and high-tech measuring and recording equipment, which allows to quickly and without repetition obtain sufficiently accurate estimates of the interaction of the spatially oriented blade of the bulldozer blade with the working environment from the primary data and made it possible to process them using modern software, which eliminated the time-consuming data processing process. This, in turn, made it possible to minimise the number of measurements of the cutting force at a given accuracy and reliability of the test results with a data probability of 0,9 to 0,95.


  • Open Access

    Overview of suspension systems for mobile wheeled robots

    by Yaroslav Korobenko, Dmytro Mishchuk, Maksym Balaka, Ярослав Коробенко, Дмитро Міщук

    A common type of transport system used in robotics is a wheeled platform with at least one drive axle and some form of suspension for each wheel. Autonomous navigation at high speed over rough terrain is a challenging and relevant task for wheeled robots. To achieve mobility on terrain, a wheeled robot must adapt and respond quickly. The suspension systems of mobile wheeled robots play a key role in ensuring their stability, maneuverability, and overall efficiency. This article presents a comprehensive overview of the different types of suspensions used in modern mobile wheeled robots. The main designs of passive and active, rigid and elastic suspensions are considered, as well as their features, advantages and disadvantages. As a result of the analysis, it was found that the optimal choice of suspension system depends on the specific operating conditions of the robot and the tasks set. For example, for robots operating in difficult terrain, suspensions with high damping are more suitable, while for robots performing precise maneuvers on a flat surface, suspension stiffness is more important. The article may be useful for engineers, researchers, and developers of robotic systems who seek to improve the designs of mobile wheeled robots and increase their efficiency and reliability. The conclusions and recommendations presented in the article can contribute to the development of new approaches to suspension design and optimization of existing solutions in the field of mobile robotics.


  • Open Access

    OVERVIEW OF TRAILED VEHICLE DESIGNS FOR TRANSPORTATION OF LARGE-SIZED AND HEAVY BUILDING EQUIPMENT AND ANALYSIS OF THEIR PARAME-TERS

    by Oleksandr Dyachenko, Maxim Balaka, Olga Kapusta, Anastasia Chernenko

    The relevance of the processes of processing construction waste into secondary raw ma-terials will only increase over the years due to the increasing number of outdated or destroyed buildings that are not suitable for further operation. The processing of concrete into secondary crushed stone includes such processes as separation, sorting and grinding, which are performed directly at the places of construction waste generation. For their implementation, it is necessary to deliver specialized mobile crushing and sorting plants, which belong to large-sized and heavy equipment. Special technical means for oversized and heavy loads are used to transport mobile crushing and sorting plants, as well as other specialized equipment. The most suitable means for transporting such cargoes are trailed vehicles, namely trawls. Trawlers are manu-factured in the form of trailers or semi-trailers, which differ in the number of axles, load capacity class, height and method of loading, type of suspension, etc. In the work, an overview of the existing designs of trailer vehicles for the transportation of large-sized and heavy loads was performed, and their parameters were analyzed. According to the obtained results, it was determined that within the same load capacity class, trawls differ in terms of total weight, platform length, loading height, metal capacity of the structure and other parameters. The advantages and disadvantages of various layout schemes of road trains (tractor and trailer) are determined. Knowledge of the constructions of these vehicles, their parameters and operational features allows you to make a choice in accordance with the conditions of transportation, characteristics of the cargo, the distance of transportation and routes.