IHIhor Honta

Ihor Honta

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ihor Honta has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ЕКСПЕРИМЕНТАЛЬНІ ДОСЛІДЖЕННЯ ПРОЦЕСУ РІЗАННЯ ҐРУНТУ НАКОНЕЧНИКОМ З ДИНАМІЧНОЮ РІЖУЧОЮ КРОМКОЮ

    by М.о. Пристайло, М.м. Балака, А.г. Поліщук, І.п. Гонта

    The experimental study results of the of soil cutting with dynamic cutting edge tip and the pneumatic accumulator are presented in the paper. Recent research and publications indicate increasing attention to improving the energy efficiency of earthmoving processes through adaptive and energy-storing working elements; however, existing theoretical models remain insufficiently accurate for predicting force interaction parameters in complex soil–tool systems. This creates the need for experimental verification and refinement of analytical approaches. The purpose of the study is to experimentally determine the cutting resistance force and to establish its dependence on the pressure level in the pneumatic accumulator. The main research methods include physical modeling using the paraffin-based soil analogue, strain-gauge measurements, and mathematical processing of experimental data with subsequent comparative analysis against theoretical predictions. The obtained results demonstrate the pronounced nonlinear dependence of cutting force on pressure, characterized by the U-shaped curve. It was found that the system exhibits an optimal pressure range, within which the minimum cutting resistance and the most energy-efficient operating regime are achieved. Outside this range, both low and excessive pressure levels lead to increased cutting resistance due to insufficient damping or excessive system rigidity. The comparison between experimental and theoretical results showed good agreement, with the deviation of up to 11%, confirming the adequacy of the proposed theoretical model. The results obtained can be used for the design and optimization of working elements of construction machinery aimed at reducing energy consumption and improving operational efficiency.

  • Open Access

    Optimization of soil cutting process by ripper tip with dynamic cutting edge

    by Mykola Prystailo, Maksym Balaka, Andrii Polischuk, Andrii Kozak, Ihor Honta

    The mechanical processes of interaction between the ripper tip with the dynamic cutting edge on the pneumatic accumulator and the soil massif are investigated in the paper. Rheological models of the soil are considered, describing its elastic and viscoelastic properties, as well as the regularities of deformation under the action of the working element. The movement speed of the ripper tip, the dynamics of changes in cutting force, and the formation nature of the compressed zone for different soil categories are investigated based on the combination of analytical methods and experimental tests. The results obtained allowed us to establish the influence regularities of the ripper tip parameters on power loads, energy consumption and stability of the technological process. It is shown that the ripper tip use with the dynamic cutting edge on the pneumatic accumulator contributes to the decrease in peak and average loads, the decrease in friction forces and vibration oscillations. This leads to an increase in energy efficiency, the decrease in dynamic shocks and the increase in the resource of the working element. It’s found that the maximum effect is achieved during the development of light and medium-density soils, where the greatest reduction in cutting force and the highest process stability are observed. The energy effect is less pronounced for strong soils, but the positive effect on load stabilization is preserved. The practical significance of the results obtained lies in the possibility of improving the designs of ripper tips, substantiating rational modes of their operation. It also aims at increasing the efficiency of technological processes during preparatory works in transport and industrial construction, mining and the agricultural sector.

  • Open Access

    Innovative ways to improve machines for preliminary work given the needs of the modern construction industry

    by Mykola Prystailo, Maksym Balaka, Valentyn Mozharivskyi, Volodymyr Drachuk, Ihor Honta, Микола Пристайло, Валентин Можарівський, Ігор Гонта

    The bulldozer-ripper is the main machine during preliminary work. The creation of high-performance machines is carried out in two directions: the production of fundamentally new working elements and machines based on the use of fundamental scientific achievements and the improvement of existing working elements, and traditional type machines that are in operation. The creation of working elements for ripper-picks is a perspective development direction of machines designed for ripping frozen and hard soils. They would make it possible to significantly increase the productivity of ripping work through the rational use of the base machine traction force. We applied the superposition principle of the impact on the working medium of several factors concurrently for this, such as static and dynamic loads, through the energy accumulation and its subsequent use to create a high-speed power impulse on the cutting edge to ensure the preliminary formation of the compressed zone in the soil massif. This will lead to the power intensity reduction of the static load on the soil element separation.