Ahmad Ghazanfari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ahmad Ghazanfari has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
S. Emami
Department of Agricultural and Bioresource Engineering University of Saskatchewan, Saskatoon, SK, Canada
4 shared publicationsS. Panigrahi
Department of Agricultural and Bioresource Engineering University of Saskatchewan, Saskatoon, SK, Canada
4 shared publications- Lope G. Tabil
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, S7N 5A9, Canada
3 shared publications L. G. Tabil
Department of Agricultural and Bioresource Engineering , University of Saskatchewan , Saskatoon, Saskatchewan, Canada
2 shared publicationsMehdi Sarcheshmehpour
2 shared publications- Ali Mohebbi
Department of Chemical Engineering Faculty of Engineering Shahid Bahonar University of Kerman Kerman Iran
1 shared publication
Latest Publications
- 13 April 2020
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 56 (6) , 1152-1167
Improvement hydrocyclone separation of biodiesel impurities prepared from waste cooking oil using CFD simulation
Raw biodiesel usually contains a considerable amount of impurities that need to be separated. In this work, a 10-mm diameter Dorr-Oliver hydrocyclone was used to investigate the separate behavior of impurities from biodiesel prepared from waste cooking oil under different operational conditions. The experimental results showed a maximum impurity separation of 82.2% (v/v). The operational conditions including inlet mixture temperature, pressure drop across the hydrocyclone, and the percentage of inlet impurities were optimized using Taguchi method. Then, the hydrocyclone was modeled using CFD to optimize its dimensions. The experiments performed by the optimized hydrocyclone indicated an impurities separation of 90.76%.
- 13 April 2020
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 56 (6) , 1152-1167
Improvement hydrocyclone separation of biodiesel impurities prepared from waste cooking oil using CFD simulation
Raw biodiesel usually contains a considerable amount of impurities that need to be separated. In this work, a 10-mm diameter Dorr-Oliver hydrocyclone was used to investigate the separate behavior of impurities from biodiesel prepared from waste cooking oil under different operational conditions. The experimental results showed a maximum impurity separation of 82.2% (v/v). The operational conditions including inlet mixture temperature, pressure drop across the hydrocyclone, and the percentage of inlet impurities were optimized using Taguchi method. Then, the hydrocyclone was modeled using CFD to optimize its dimensions. The experiments performed by the optimized hydrocyclone indicated an impurities separation of 90.76%.
- 24 April 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 42 (18) , 2214-2226
A weighted principal component analysis approach for online quality determination of biodiesel using spectrophotometry data
Biodiesel fuels deteriorate when exposed to air or high temperatures. In this study, biodiesel was produced through transesterification of sunflower oil and kept at 25, 45, and 70°C for 28 days. The spectrophotometry graphs of the samples were prepared and used as inputs to three classification schemes of linear discrimination analysis, principal component analysis (PCA), and weighted PCA (WPCA) to categorize the fuels into three groups, based on their acid values. The resulting average recognition accuracies were 82%, 84%, and 96% for the three classifiers, respectively. The analysis of the classifiers outputs indicated that the wavelengths between 200 and 240 nm had the higher significant role in determining the quality of the fuels. The model assessment and error analysis of the results were performed using Hotelling T2 statistic and Q-residual index. The analysis indicated the WPCA model, at a 5% significance level, had higher power for accurately determining the quality of biodiesel samples using their spectrophotometry data.
- 24 April 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 42 (18) , 2214-2226
A weighted principal component analysis approach for online quality determination of biodiesel using spectrophotometry data
Biodiesel fuels deteriorate when exposed to air or high temperatures. In this study, biodiesel was produced through transesterification of sunflower oil and kept at 25, 45, and 70°C for 28 days. The spectrophotometry graphs of the samples were prepared and used as inputs to three classification schemes of linear discrimination analysis, principal component analysis (PCA), and weighted PCA (WPCA) to categorize the fuels into three groups, based on their acid values. The resulting average recognition accuracies were 82%, 84%, and 96% for the three classifiers, respectively. The analysis of the classifiers outputs indicated that the wavelengths between 200 and 240 nm had the higher significant role in determining the quality of the fuels. The model assessment and error analysis of the results were performed using Hotelling T2 statistic and Q-residual index. The analysis indicated the WPCA model, at a 5% significance level, had higher power for accurately determining the quality of biodiesel samples using their spectrophotometry data.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Environment and Waste Management
- Vol. 23 (2) , 179
Investigating composting progress of kitchen wastes using rate of change and cross-correlation approaches
Kitchen wastes usually require addition of some bulking agent for proper composting. In this study, mixtures of kitchen and pruning of elm trees were composted under three treatments of natural, low and high aeration rates. Temperature, ammonia, carbon monoxide, pH and volatile organic matter were monitored and analysed. The results indicated with increase in aeration rate, temperature of the treatments increased. The pH values of the treatments decreased initially to a minimum of 5.0 and then increased continuously. The emitted ammonia and CO initially rose but then continually decreased. The rate of change graphs showed two distinct phases of: 1) active; 2) constant rate for all measured factors. A correlation analysis on the five considered factors indicated the reduction in volatile organic matter and emitted CO and ammonia were highly negatively correlated with pH of the pile (r = −0.72), but their correlations with temperature were low.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Environment and Waste Management
- Vol. 23 (2) , 179
Investigating composting progress of kitchen wastes using rate of change and cross-correlation approaches
Kitchen wastes usually require addition of some bulking agent for proper composting. In this study, mixtures of kitchen and pruning of elm trees were composted under three treatments of natural, low and high aeration rates. Temperature, ammonia, carbon monoxide, pH and volatile organic matter were monitored and analysed. The results indicated with increase in aeration rate, temperature of the treatments increased. The pH values of the treatments decreased initially to a minimum of 5.0 and then increased continuously. The emitted ammonia and CO initially rose but then continually decreased. The rate of change graphs showed two distinct phases of: 1) active; 2) constant rate for all measured factors. A correlation analysis on the five considered factors indicated the reduction in volatile organic matter and emitted CO and ammonia were highly negatively correlated with pH of the pile (r = −0.72), but their correlations with temperature were low.
- 7 November 2017
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 35 (12) , 1226-1236
A novel kinetic modeling method for the stabilization phase of the composting process for biodegradation of solid wastes
Biomass degradation kinetics of the composting process for kitchen waste, pruned elm tree branches and sheep manure were studied to model changes in volatile solids (VS) over time. Three experimental reactors containing raw mixtures with a carbon to nitrogen (C/N) ratio of 27:1 and a moisture content of 65% were prepared. During the composting process two of the reactors used forced air and the third used natural aeration. The composting stabilization phases in all reactors were completed in 30 days. During this period, composting indexes such as temperature, moisture content and VS changes were recorded. Elementary reactions were used for kinetics modeling of the degradation process. Results showed that the numerical values of rate constant ( k) for zero-order ranged from 0.86 to 1.03 VS×day-1, for first-order models it ranged from 0.01 to 0.02 day-1, for second-order the range was from 1.36×10-5 to 1.78×10-5 VS-1×day-1 and for n-order the rate constant ranged from 0.031 to 0.095 VS(1-n)×day-1. The resulting models were validated by comparing statistical parameters. Evaluation of the models showed that, in the aerated reactors, the n-order models (less than 1) successfully estimated the VS changes. In the non-aeration reactor, for the second-order model good agreement was achieved between the simulated and actual quantities of VS. Also, half-life time provided a useful criterion for the estimation of expected time for completion of different phases of composting.
- 7 November 2017
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 35 (12) , 1226-1236
A novel kinetic modeling method for the stabilization phase of the composting process for biodegradation of solid wastes
Biomass degradation kinetics of the composting process for kitchen waste, pruned elm tree branches and sheep manure were studied to model changes in volatile solids (VS) over time. Three experimental reactors containing raw mixtures with a carbon to nitrogen (C/N) ratio of 27:1 and a moisture content of 65% were prepared. During the composting process two of the reactors used forced air and the third used natural aeration. The composting stabilization phases in all reactors were completed in 30 days. During this period, composting indexes such as temperature, moisture content and VS changes were recorded. Elementary reactions were used for kinetics modeling of the degradation process. Results showed that the numerical values of rate constant ( k) for zero-order ranged from 0.86 to 1.03 VS×day-1, for first-order models it ranged from 0.01 to 0.02 day-1, for second-order the range was from 1.36×10-5 to 1.78×10-5 VS-1×day-1 and for n-order the rate constant ranged from 0.031 to 0.095 VS(1-n)×day-1. The resulting models were validated by comparing statistical parameters. Evaluation of the models showed that, in the aerated reactors, the n-order models (less than 1) successfully estimated the VS changes. In the non-aeration reactor, for the second-order model good agreement was achieved between the simulated and actual quantities of VS. Also, half-life time provided a useful criterion for the estimation of expected time for completion of different phases of composting.
- 25 February 2017
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 9 (7) , 1213-1221
Optimizing the Production Parameters for Pellets Made from Pistachio Tree Pruning Using Multi-response Optimization
- 25 February 2017
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 9 (7) , 1213-1221
Optimizing the Production Parameters for Pellets Made from Pistachio Tree Pruning Using Multi-response Optimization
- 3 July 2010
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE B
- Vol. 11 (7) , 482-488
Finite element analysis and modeling of water absorption by date pits during a soaking process
Date pits for feed preparation or oil extraction are soaked in water to soften before milling or extrusion. Knowledge of water absorption by the date pits helps in better managing the soaking duration. In this research, the process of water absorption by date pits was modeled and analyzed using Fick’s second law of diffusion, finite element approach, and Peleg model. The moisture content of the pits reached to its saturation level of 41.5% (wet basis) after 10 d. The estimated coefficient of diffusion was 9.89×10−12 m2/s. The finite element model with a proposed ellipsoid geometry for a single date pit and the analytical model fitted better to the experimental data with R 2 of 0.98. The former model slightly overestimated the moisture content of the pits during the initial stages of the soaking and the latter model generally underestimated this variable through the entire stages of soaking process.
- 3 July 2010
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE B
- Vol. 11 (7) , 482-488
Finite element analysis and modeling of water absorption by date pits during a soaking process
Date pits for feed preparation or oil extraction are soaked in water to soften before milling or extrusion. Knowledge of water absorption by the date pits helps in better managing the soaking duration. In this research, the process of water absorption by date pits was modeled and analyzed using Fick’s second law of diffusion, finite element approach, and Peleg model. The moisture content of the pits reached to its saturation level of 41.5% (wet basis) after 10 d. The estimated coefficient of diffusion was 9.89×10−12 m2/s. The finite element model with a proposed ellipsoid geometry for a single date pit and the analytical model fitted better to the experimental data with R 2 of 0.98. The former model slightly overestimated the moisture content of the pits during the initial stages of the soaking and the latter model generally underestimated this variable through the entire stages of soaking process.
- 10 January 2008
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 42 (1) , 77-89
Thermal and Mechanical Properties of Blends and Composites from HDPE and Date Pits Particles
The date pits flour was used as a filling material in composition with high density polyethylene (HDPE). The blending proportions were: (1) 10% date pits, 90% HDPE; (2) 20% date pits, 80% HDPE; (3) 30% date pits, 70% HDPE; and (4) 40% date pits, 60% HDPE. Thermal conductivities, specific heat, and melt flow index of the blends were determined. The thermal conductivities ranged from 0.460 to 0.720 W/(m°C) and specific heats ranged from 1.10 to 5.30 kJ/(kg°C). The tensile and flexural tests on composite plates, fabricated by compress molding, indicated that strength and strain values decreased with increase in the percentage of date pits. There was no significant difference between flexural moduli of elasticity of the composites, but tensile modulus had the highest value at 30% blend. Moduli of elasticity of the composites were lower than the plates prepared from virgin HDPE at 180°C. It was presumed that high temperature processing of pure HDPE altered its original properties and consequently increased its modulus of elasticity.
- 10 January 2008
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 42 (1) , 77-89
Thermal and Mechanical Properties of Blends and Composites from HDPE and Date Pits Particles
The date pits flour was used as a filling material in composition with high density polyethylene (HDPE). The blending proportions were: (1) 10% date pits, 90% HDPE; (2) 20% date pits, 80% HDPE; (3) 30% date pits, 70% HDPE; and (4) 40% date pits, 60% HDPE. Thermal conductivities, specific heat, and melt flow index of the blends were determined. The thermal conductivities ranged from 0.460 to 0.720 W/(m°C) and specific heats ranged from 1.10 to 5.30 kJ/(kg°C). The tensile and flexural tests on composite plates, fabricated by compress molding, indicated that strength and strain values decreased with increase in the percentage of date pits. There was no significant difference between flexural moduli of elasticity of the composites, but tensile modulus had the highest value at 30% blend. Moduli of elasticity of the composites were lower than the plates prepared from virgin HDPE at 180°C. It was presumed that high temperature processing of pure HDPE altered its original properties and consequently increased its modulus of elasticity.
- 1 December 2006
- Published by Taylor & Francis in Drying Technology
- Vol. 24 (12) , 1643-1648
Thin-Layer Drying of Flax Fiber: III. Influence of Layer Thickness on Drying Parameters
Wet flax fiber was dried after rinsing at four layer thicknesses of 5, 10, 15, and 20 mm using four drying air temperatures of 30, 50, 70, and 100°C. The coefficients of diffusion of flax fiber at different drying conditions were estimated using a three-term series solution of Fick's second law of diffusion. The Page model was used to model the drying characteristic curves. The estimated coefficient of diffusion of the flax fiber and the drying constant of the Page model were both linearly proportional to drying air temperature and increased exponentially with the thickness of the drying layer.
- 1 December 2006
- Published by Taylor & Francis in Drying Technology
- Vol. 24 (12) , 1643-1648
Thin-Layer Drying of Flax Fiber: III. Influence of Layer Thickness on Drying Parameters
Wet flax fiber was dried after rinsing at four layer thicknesses of 5, 10, 15, and 20 mm using four drying air temperatures of 30, 50, 70, and 100°C. The coefficients of diffusion of flax fiber at different drying conditions were estimated using a three-term series solution of Fick's second law of diffusion. The Page model was used to model the drying characteristic curves. The estimated coefficient of diffusion of the flax fiber and the drying constant of the Page model were both linearly proportional to drying air temperature and increased exponentially with the thickness of the drying layer.
- 1 December 2006
- Published by Taylor & Francis in Drying Technology
- Vol. 24 (12) , 1637-1642
Thin-Layer Drying of Flax Fiber: II. Modeling Drying Process Using Semi-Theoretical and Empirical Models
Thin-layer drying experiments were performed for drying flax fiber under four different drying conditions. In all drying treatments the absolute humidity of drying air was 0.0065 kg of water per kg of dry air, but the drying temperature were 30, 50, 70, and 100°C. The drying process was modeled using the drying data and five semi−theoretical and empirical models cited in different literatures. From the five tested models, the Page model gave the best fitting for experimental data with R 2 equal to 0.99, for all treatments. The estimated drying constants at different drying temperatures were highly correlated with drying air temperature. The drying constants were also highly correlated with the calculated coefficient of diffusions.
- 1 December 2006
- Published by Taylor & Francis in Drying Technology
- Vol. 24 (12) , 1637-1642
Thin-Layer Drying of Flax Fiber: II. Modeling Drying Process Using Semi-Theoretical and Empirical Models
Thin-layer drying experiments were performed for drying flax fiber under four different drying conditions. In all drying treatments the absolute humidity of drying air was 0.0065 kg of water per kg of dry air, but the drying temperature were 30, 50, 70, and 100°C. The drying process was modeled using the drying data and five semi−theoretical and empirical models cited in different literatures. From the five tested models, the Page model gave the best fitting for experimental data with R 2 equal to 0.99, for all treatments. The estimated drying constants at different drying temperatures were highly correlated with drying air temperature. The drying constants were also highly correlated with the calculated coefficient of diffusions.