ANAmjad Nawaz

Amjad Nawaz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Amjad Nawaz has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High-Fidelity OpenMC Neutronic Verification of the gFHR Benchmark with Double-Heterogeneity Representations and HPC Scalability

    by Muhammad Aqib Yasin, Awais Zahur, Amjad Nawaz, Anwar Hussain, Muhammad Rizwan Ali

    Pebble-bed reactors pose significant challenges for high-fidelity neutronics modeling owing to the double-heterogenous TRISO fuel and stochastic pebble arrangement. The generic fluoride salt-cooled high-temperature reactor (gFHR) benchmark provides an open reference problem for assessing reactor physics codes. However, its systematic evaluation using OpenMC has not previously been reported. Hence, this study develops and verifies a continuous-energy OpenMC model for gFHR benchmark and systematically investigates the neutronic and computational effects of representing double heterogeneity at the core level. In addition to fully stochastic placement, simple hexagonal (HEX) and hexagonal close-packed (HCP) lattice geometries are used to construct five representations of the double-heterogeneous fuel structure: fully stochastic, HEX-HEX, HCP-HCP, HEX-Stochastic, and HCP-Stochastic. The calculated effective multiplication factors agree well with benchmark results across all five representations. Radial and axial power distributions show good agreement with reference solutions. The comparisons of neutron flux distributions reveal local differences among geometry representations near the pebble-bed/reflector interfaces despite similar core-averaged neutron spectra. Significant differences in computational cost are observed among the geometry representations. The HEX-HEX and HCP-HCP configurations provide 71× and 16× speedups, respectively, relative to the fully stochastic model. Parallel calculations of the fully stochastic model using up to 8 nodes and 704 cores achieve a MPI speedup of 7.52×, with the wall-clock time decreasing from 13 h to 1.8 h. These results demonstrate that OpenMC can accurately reproduce the neutronic behavior of the gFHR benchmark and provide quantitative accuracy-cost guidance for geometry representation in future gFHR analyses.

  • Open Access

    Evaluation of Using Reflector Drums as an Alternate Reactivity Control Mechanism in PWR-type Small Modular Reactors

    by Safoora Rana, Alam Nawaz Khan Wardag, Sajjad Tahir, Rustam Khan, Anwar Hussain, Amjad Nawaz, Sikander M. Mirza

    Development of simplified and inherently safe reactivity control mechanisms is still a challenge in many compact Small Modular Reactors (SMRs), despite significant progress. One such approach is the use of rotating reflector drums, which have been extensively employed in space reactor systems, but their application to light-water SMRs remains unexplored. This study investigates the application of rotating reflector drums as a primary reactivity control system in a light water SMR by quantifying achievable reactivity swing and shutdown margin. A 5 MWth nuclear heating reactor (NHR-5) design was used as a base design model, to analyze different configurations of reflector drums and to perform their neutronic simulations using Monte Carlo code. According to the current results, complete reflector drum rotation can provide sufficient reactivity swing to shut down the reactor and provides operational control within limits. This model uses beryllium filled reflector drums, with approximately 1224 pcm reactivity worth, which eliminates the rod ejection accidents, increases the fuel cycle length and reduces the risk of rapid reactivity insertion and mechanical complexity and consequently enhances the reactor safety as compared to the control rod mechanism.

  • Open Access

    The Investigation of Nonavailability of Passive Safety Systems Effects on Small Break LOCA Sequence in AP1000 Using RELAP5 MOD 4.0

    by Anwar Hussain, Amjad Nawaz

    The passive safety systems of AP1000 are designed to operate automatically at desired set-points. However, the unavailability or failure to operate of any of the passive safety systems will change the accident sequence and may affect reactor safety. The analysis in this study is based on some hypothetical scenarios, in which the passive safety system failure is considered during the loss of coolant accidents. Four different cases are assumed, that is, with all passive systems, without actuation of one of the accumulators, without actuation of ADS stages 1–3, and without actuation of ADS stage 4. The actuation of all safety systems at their actuation set-points provides adequate core cooling by injecting sufficient water inventory into reactor core. The LOCA with actuation of one of the accumulators cause early actuation of ADS and IRWST. In case of LOCA without ADS stages 1–3, the primary system depressurization is relatively slow and mixture level above core active region drops much earlier than IRWST actuation. The accident without ADS stage 4 actuation results in slow depressurization and mixture level above core active region drops earlier than IRWST injection. Moreover, the comparison of cladding surface temperature is performed in all cases considered in this work.


  • Modification of thermal hydraulic code, THEATRe, with fuel rod behavior models and its application to reactivity-initiated accident (RIA)

    by Amjad Nawaz, Hidekazu Yoshikawa, Ming Yang, Anwar Hussain

    During reactor operation, many complex changes occur in fuel rod which affects its thermal, mechanical and material properties. These changes also affect the reactor response to the transient and accident situations. Realistic simulation of fuel rod behavior under transients such as reactivity-initiated accident (RIA) is of great significance. In this study, thermal hydraulic analysis code THEATRe (Thermal Hydraulic Engineering Analysis Tool in Real-time) has been modified by addition of fuel rod behavior models for dynamic simulation of nuclear reactor. Transient changes in gas-gap parameters were taken into account by modeling the gas-gap behavior. Thermo-mechanical behavior of fuel rod is modeled to take into account the thermal, elastic and plastic deformation. To simulate RIA, point reactor kinetics model is also incorporated in the THEATRe code. To demonstrate the transient fuel rod behavior, AP1000 reactor is modeled and three hypothetical RIA cases are simulated. The RIA is considered at three different reactor power levels, i.e. 100, 50 and 1% of nominal power. The investigated parameters are fuel temperature, cladding stress and strain, fuel and cladding thermal conductivity and heat transfer coefficient in gas-gap. Modified code calculates the fuel rod temperatures according to updated fuel, clad and gas-gap parameters at the onset of steady-state operation and during the transient. The modified code provides lower steady-state fuel temperature as compared to the original code. Stress and strain analyses indicate that the hoop and radial strain is higher at high power locations of the fuel rod; therefore, gap closure process will initially occur in the central portion of the fuel rod and it should be given more emphasis in the safety analysis of the fuel rod and nuclear reactor during accidents and transients.