Jonathan Coburn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jonathan Coburn has a total of 176 co-authors. Here are the top co-authors by number of shared publications:
- Tyler Abrams
General Atomics 1 , San Diego, California 92121
6 shared publications - Dmitry L. Rudakov
University of California
5 shared publications - Charles Lasnier
Lawrence Livermore National Laboratory
4 shared publications - Claudio Marini
University of California San Diego
4 shared publications - Richard A. Pitts
ITER Organization
4 shared publications - Ryan Hood
Sandia National Laboratory
4 shared publications
Latest Publications
- Open Access
- 5 November 2026
- Published by IOP Publishing in Nuclear Fusion
Performance and damage mechanisms of dispersion-strengthened tungsten under H-mode plasma in DIII-D
Dispersion strengthened tungsten (DSW) alloys are promising materials for plasma facing components, displaying improved mechanical properties and microstructure stability compared to pure tungsten. In this work, the performance of DSW reinforced with 1 wt% transition-metal carbide (TaC, TiC, or ZrC) has been examined under H-mode plasma in the DIII-D tokamak. DSW samples were mounted both flush with the divertor floor and at a 10° angle towards the incoming plasma fluxes to further increase the heat and particle loading. To simulate the impact of prolonged tokamak operation, similar plasma exposures were repeated on two additional sets of DSW samples: one set pre-implanted with 10 22 m -2 helium, and another set heated in-situ to an additional 500°C. Flush mounted samples exhibited good surface stability, with no evidence of melting or cracking regardless of composition or treatment. Carbon redeposition was observed on most samples, likely due to the graphite environment of DIII-D. Under coupled thermal loading and helium implantation, surface nanostructuring developed in some DSW samples; however, DSW containing tantalum dispersion phases showed strong resistance to such surface modification. In contrast, obvious surface melting was observed on 10° angled samples containing TaC and ZrC dispersoids, likely associated with dispersoid oxidation during fabrication, which reduced thermal conductivity and promoted elevated surface temperatures during plasma exposure. The grain morphology of DSW containing TiC remained largely unchanged, although near-surface dispersoids on the angled TiC sample were missing after plasma exposure. The loss is associated with oxidation of the dispersoids during fabrication, followed by sublimation during plasma exposure. Through systematic comparison of DSW performance under H-mode plasma conditions, this study identifies key degradation mechanisms and highlights strategies to improve the performance of DSW as plasma facing materials.
- 5 November 2026
- Published by IOP Publishing in Nuclear Fusion
Open AccessPerformance and damage mechanisms of dispersion-strengthened tungsten under H-mode plasma in DIII-D
Dispersion strengthened tungsten (DSW) alloys are promising materials for plasma facing components, displaying improved mechanical properties and microstructure stability compared to pure tungsten. In this work, the performance of DSW reinforced with 1 wt% transition-metal carbide (TaC, TiC, or ZrC) has been examined under H-mode plasma in the DIII-D tokamak. DSW samples were mounted both flush with the divertor floor and at a 10° angle towards the incoming plasma fluxes to further increase the heat and particle loading. To simulate the impact of prolonged tokamak operation, similar plasma exposures were repeated on two additional sets of DSW samples: one set pre-implanted with 10 22 m -2 helium, and another set heated in-situ to an additional 500°C. Flush mounted samples exhibited good surface stability, with no evidence of melting or cracking regardless of composition or treatment. Carbon redeposition was observed on most samples, likely due to the graphite environment of DIII-D. Under coupled thermal loading and helium implantation, surface nanostructuring developed in some DSW samples; however, DSW containing tantalum dispersion phases showed strong resistance to such surface modification. In contrast, obvious surface melting was observed on 10° angled samples containing TaC and ZrC dispersoids, likely associated with dispersoid oxidation during fabrication, which reduced thermal conductivity and promoted elevated surface temperatures during plasma exposure. The grain morphology of DSW containing TiC remained largely unchanged, although near-surface dispersoids on the angled TiC sample were missing after plasma exposure. The loss is associated with oxidation of the dispersoids during fabrication, followed by sublimation during plasma exposure. Through systematic comparison of DSW performance under H-mode plasma conditions, this study identifies key degradation mechanisms and highlights strategies to improve the performance of DSW as plasma facing materials.
- Open Access
- 10 May 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Retention and surface morphology evaluation of fine-grain dispersion-strengthened tungsten for plasma-facing component applications
- 10 May 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Open AccessRetention and surface morphology evaluation of fine-grain dispersion-strengthened tungsten for plasma-facing component applications
- Open Access
- 14 January 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 46
Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D
- 14 January 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 46
Open AccessOverview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D
- Open Access
- 5 September 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Recrystallization, cracking, and erosion of dispersoid-strengthened tungsten materials during exposure to divertor plasmas
- 5 September 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Open AccessRecrystallization, cracking, and erosion of dispersoid-strengthened tungsten materials during exposure to divertor plasmas
- Open Access
- 9 June 2025
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 81 (7) , 642-660
Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D
- 9 June 2025
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 81 (7) , 642-660
Open AccessThree-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D
- 1 March 2025
- Published by Office of Scientific and Technical Information (OSTI)
High Durability Plasma Facing Composites
- 1 March 2025
- Published by Office of Scientific and Technical Information (OSTI)
High Durability Plasma Facing Composites
- Open Access
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Sandia National Laboratories Boundary Physics Research at DIII-D
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessSandia National Laboratories Boundary Physics Research at DIII-D