Moaaz Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Moaaz Ahmed has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Amine Bermak
Hamad Bin Khalifa University
19 shared publications Wei Xu
Hong Kong University of Science and Technology, Dept. of Mechanical and Aerospace Engineering, Hong Kong SAR
6 shared publications- Bo Wang
College of Science and Engineering, Hamad bin Khalifa University, Doha, Qatar
5 shared publications Yi-Kuen Lee
HKUST, Dept of MAE, Hong Kong SAR, China
5 shared publications- Mingzheng Duan
The Hong Kong University of Science and Technology
4 shared publications Saqib Mohamad
Department of Electronic and Computer Engineering, Hong Kong University of Science and Technology, Hong Kong, China
4 shared publications
Latest Publications
- Open Access
- 13 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (14) , 14196-14204
A Laser Doppler Blood Flow Measurement System With a 151.4 dBΩ Gain and 0.05% Nonlinearity for PAD Patients
This article presents a compact blood flow measurement system exploiting the Doppler effect and photocurrent sensing technique for wearable health monitoring. Specifically, it helps the patients suffering from peripheral artery disease (PAD) to monitor the blood flow continuously without involving a physician or medical expert. The system prototype integrates a laser diode, a photodiode, and an analog front-end (AFE) on a 54 mm $\times64$ mm three-layer PCB using discrete components for proof of concept. The front-end is designed with two output modes providing simultaneous current-to-voltage and current-to-frequency conversion without requiring an external clock source. Moreover, this system does not require optical filters or fibers, dynamic artifacts are therefore significantly reduced. Drawing 33 mA current from a 3.3-V supply, the developed system offers a transimpedance gain of 151.4 dB $\Omega $ for the voltage mode output. For the frequency output, a nonlinearity of 0.05% is achieved.
- 13 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (14) , 14196-14204
Open AccessA Laser Doppler Blood Flow Measurement System With a 151.4 dBΩ Gain and 0.05% Nonlinearity for PAD Patients
This article presents a compact blood flow measurement system exploiting the Doppler effect and photocurrent sensing technique for wearable health monitoring. Specifically, it helps the patients suffering from peripheral artery disease (PAD) to monitor the blood flow continuously without involving a physician or medical expert. The system prototype integrates a laser diode, a photodiode, and an analog front-end (AFE) on a 54 mm $\times64$ mm three-layer PCB using discrete components for proof of concept. The front-end is designed with two output modes providing simultaneous current-to-voltage and current-to-frequency conversion without requiring an external clock source. Moreover, this system does not require optical filters or fibers, dynamic artifacts are therefore significantly reduced. Drawing 33 mA current from a 3.3-V supply, the developed system offers a transimpedance gain of 151.4 dB $\Omega $ for the voltage mode output. For the frequency output, a nonlinearity of 0.05% is achieved.
- Open Access
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 23 (10) , 18145-18154
Multidomain Suppression of Ambient Light in Visible Light Communication Transceivers
Visible light communication (VLC) transceivers suffer from optical interference and ambient light saturation, which severely affect the reception of optical signals. In this paper, we discuss various techniques for the suppression of ambient light in electronic, optical, communication and wavelength domains with focus on VLC systems for vehicular communication. Designing transceivers for outdoor VLC systems is challenging due to the dynamic environment and the time-varying nature of interference from different types of ambient light sources. This is a unique study that addresses the problem of optical interference in multiple physical domains and offers qualitative insights in a systematic manner.
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 23 (10) , 18145-18154
Open AccessMultidomain Suppression of Ambient Light in Visible Light Communication Transceivers
Visible light communication (VLC) transceivers suffer from optical interference and ambient light saturation, which severely affect the reception of optical signals. In this paper, we discuss various techniques for the suppression of ambient light in electronic, optical, communication and wavelength domains with focus on VLC systems for vehicular communication. Designing transceivers for outdoor VLC systems is challenging due to the dynamic environment and the time-varying nature of interference from different types of ambient light sources. This is a unique study that addresses the problem of optical interference in multiple physical domains and offers qualitative insights in a systematic manner.
- 29 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Deep Learning-based Face Mask Usage Detection on Low Compute Resource Devices
The advent of the COVID-19 pandemic has brought several never-before-seen changes in the daily lives of people around the globe. As a way to curb the spreading of the disease, wearing face masks has become mandatory in the majority of public places. To solve the necessity of face mask detection in such situations, there have been only a handful of research endeavors up to this date. Computer vision has advanced multi-fold with the advent of AlexNet architecture. With a motivation to go deeper with the neural network architecture, the concept of Depthwise Separable Convolutions and projection layer was developed in MobileNetV1. In this work, a novel lightweight deep learning model based on Single Shot Detector (SSD) MobileNetV2 architecture is proposed for face mask detection using images and video streams of crowds aiming its utilization on low compute re-source environment. An open benchmark face mask dataset, with 4095 images including masked and no mask images, is utilized to train the model for detection. The model is initialized using transfer learning with the freezing of base layers. The proposed methodology can efficiently aid in tracking and enforcing social distancing rules in crowded places with the use of surveillance cameras. On the different benchmarks that we have tested, the model proved to be highly successful and has achieved an accuracy rate of 99.39% and an F1 score of 0.995.
- 29 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Deep Learning-based Face Mask Usage Detection on Low Compute Resource Devices
The advent of the COVID-19 pandemic has brought several never-before-seen changes in the daily lives of people around the globe. As a way to curb the spreading of the disease, wearing face masks has become mandatory in the majority of public places. To solve the necessity of face mask detection in such situations, there have been only a handful of research endeavors up to this date. Computer vision has advanced multi-fold with the advent of AlexNet architecture. With a motivation to go deeper with the neural network architecture, the concept of Depthwise Separable Convolutions and projection layer was developed in MobileNetV1. In this work, a novel lightweight deep learning model based on Single Shot Detector (SSD) MobileNetV2 architecture is proposed for face mask detection using images and video streams of crowds aiming its utilization on low compute re-source environment. An open benchmark face mask dataset, with 4095 images including masked and no mask images, is utilized to train the model for detection. The model is initialized using transfer learning with the freezing of base layers. The proposed methodology can efficiently aid in tracking and enforcing social distancing rules in crowded places with the use of surveillance cameras. On the different benchmarks that we have tested, the model proved to be highly successful and has achieved an accuracy rate of 99.39% and an F1 score of 0.995.
- 1 June 2021
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 323
Inkjet printing of multi-stripes based deflection monitoring sensor on flexible substrate
- 1 June 2021
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 323
Inkjet printing of multi-stripes based deflection monitoring sensor on flexible substrate
- 26 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 168-172
A 10-bit Pulse Width Modulation Based Analog to Digital Converter
A 10-bit pulse width modulated analog to digital converter (ADC) is proposed in this paper. The ADC is based on simple analog blocks and designed to operate as a back-end digital interface for sensor readout circuits. Our design incorporates simple blocks such as a chopped comparator and a 10-bit digital counter with few switches and passive elements to implement a very functional and versatile ADC for bridge readout circuits. Designed and simulated in 0.18µm CMOS process, the ADC consumes 55µA supply current and achieves an linearity of around 9-bits without any jitter compensation. The simulated DNL error is less than ±1 LSB for this ADC.
- 26 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 168-172
A 10-bit Pulse Width Modulation Based Analog to Digital Converter
A 10-bit pulse width modulated analog to digital converter (ADC) is proposed in this paper. The ADC is based on simple analog blocks and designed to operate as a back-end digital interface for sensor readout circuits. Our design incorporates simple blocks such as a chopped comparator and a 10-bit digital counter with few switches and passive elements to implement a very functional and versatile ADC for bridge readout circuits. Designed and simulated in 0.18µm CMOS process, the ADC consumes 55µA supply current and achieves an linearity of around 9-bits without any jitter compensation. The simulated DNL error is less than ±1 LSB for this ADC.
- Open Access
- 7 May 2021
- Published by IntechOpen
Vacuum-Free Fabrication of Transparent Electrodes for Soft Electronics
Optoelectronic devices are advancing from existing rigid configurations to deformable configurations. These developing devices need transparent electrodes (TEs) having high mechanical deformability while preserving the high electrical conductivity and optical transparency. In agreement with these requirements, vacuum-fabricated conventional TEs based on transparent conducting oxides (TCOs) are receiving difficulties due to its low abundance, film brittleness, and low optical transmittance. Novel solution-processed TE materials including regular metal meshes, metal nanowire (NW) grids, carbon materials, and conducting polymers have been studied and confirmed their capabilities to address the limitations of the TCO-based TEs. This chapter presents a comprehensive review of the latest advances of these vacuum-free TEs, comprising the electrode material classes, the optical, electrical, mechanical and surface feature properties of the soft TEs, and the vacuum-free practices for their fabrication.
- 7 May 2021
- Published by IntechOpen
Open AccessVacuum-Free Fabrication of Transparent Electrodes for Soft Electronics
Optoelectronic devices are advancing from existing rigid configurations to deformable configurations. These developing devices need transparent electrodes (TEs) having high mechanical deformability while preserving the high electrical conductivity and optical transparency. In agreement with these requirements, vacuum-fabricated conventional TEs based on transparent conducting oxides (TCOs) are receiving difficulties due to its low abundance, film brittleness, and low optical transmittance. Novel solution-processed TE materials including regular metal meshes, metal nanowire (NW) grids, carbon materials, and conducting polymers have been studied and confirmed their capabilities to address the limitations of the TCO-based TEs. This chapter presents a comprehensive review of the latest advances of these vacuum-free TEs, comprising the electrode material classes, the optical, electrical, mechanical and surface feature properties of the soft TEs, and the vacuum-free practices for their fabrication.
- Open Access
- 28 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 12 (4) , 1-11
Fast Detection and Tracking of a Moving Transmitter via Visible Light Communication Link
We propose a passive detection and tracking methodology for CamCom receivers in intelligent transport systems. The implemented architecture maximizes the data rate and can maintain a BER of 1.9 104 while passively detecting and tracking the moving transmitter undergoing worst-case road vibration of 30.6 mm/s. The proposed methodology is also independent of the size and shape of the transmitter and thus finds promising application in intelligent transport systems.
- 28 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 12 (4) , 1-11
Open AccessFast Detection and Tracking of a Moving Transmitter via Visible Light Communication Link
We propose a passive detection and tracking methodology for CamCom receivers in intelligent transport systems. The implemented architecture maximizes the data rate and can maintain a BER of 1.9 104 while passively detecting and tracking the moving transmitter undergoing worst-case road vibration of 30.6 mm/s. The proposed methodology is also independent of the size and shape of the transmitter and thus finds promising application in intelligent transport systems.
- 16 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (2) , 1-4
A Three-Dimensional Integrated Micro Calorimetric Flow Sensor in CMOS MEMS Technology
This letter presents a three-dimensional (3D) integrated Molybdenum (Mo) Thermoresistive Micro Calorimetric Flow (TMCF) sensor in a 0.18 μm CMOS MEMS technology. The sensor consists of a MEMS structure which is fabricated inside a sealed micro channel and a constant temperature (CT) control circuit implemented on the CMOS wafer. The MEMS structure and CMOS circuit are 3D integrated at the wafer level. For the N2 gas flow, the proposed flow sensor achieves a high sensitivity of 0.71 mV/(m/s) and a wide bidirectional detection ability of -26 ~ 26 m/s. Moreover, an Equivalent Circuit Model (ECM) is proposed in this letter, which depicts the nonlinear output/overheated temperature (Vout/μTh) sensor response to the input gas flow. This model would be an efficient tool for the design and optimization of high-performance System on Chip (SoC) calorimetric flow sensors.
- 16 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (2) , 1-4
A Three-Dimensional Integrated Micro Calorimetric Flow Sensor in CMOS MEMS Technology
This letter presents a three-dimensional (3D) integrated Molybdenum (Mo) Thermoresistive Micro Calorimetric Flow (TMCF) sensor in a 0.18 μm CMOS MEMS technology. The sensor consists of a MEMS structure which is fabricated inside a sealed micro channel and a constant temperature (CT) control circuit implemented on the CMOS wafer. The MEMS structure and CMOS circuit are 3D integrated at the wafer level. For the N2 gas flow, the proposed flow sensor achieves a high sensitivity of 0.71 mV/(m/s) and a wide bidirectional detection ability of -26 ~ 26 m/s. Moreover, an Equivalent Circuit Model (ECM) is proposed in this letter, which depicts the nonlinear output/overheated temperature (Vout/μTh) sensor response to the input gas flow. This model would be an efficient tool for the design and optimization of high-performance System on Chip (SoC) calorimetric flow sensors.
- 10 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (9) , 3415-3424
Fully Integrated Bidirectional CMOS-MEMS Flow Sensor With Low Power Pulse Operation
- 10 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (9) , 3415-3424
Fully Integrated Bidirectional CMOS-MEMS Flow Sensor With Low Power Pulse Operation
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A Dual-mode Flow Measurement System for Large Sensing Range with High Accuracy
This paper presents a smart system for large flow range measurement, consisting of a dual-mode MEMS flow sensor and the readout IC. During high flow rate (> 25 m/s), the output of the dual-mode sensor is directly digitized by a switched-capacitor incremental delta-sigma ADC with 12-bits resolution due to its large output amplitude. While in low flow rate, the sensor output is first amplified by a capacitively-coupled instrumentation amplifier (CCIA) before digitization. A comparator is employed to enable a dynamic switching between two operation modes based on the flow rate. The readout IC can handle a large input up to 800 mV and consumes a current as low as 114 μA. The simulation results show the measurement system achieves a maximum sensing flow rate of 73 m/s while contributes a maximum measurement error rate of 300 ppm which is considerably lower than the industry standard of 3%.
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A Dual-mode Flow Measurement System for Large Sensing Range with High Accuracy
This paper presents a smart system for large flow range measurement, consisting of a dual-mode MEMS flow sensor and the readout IC. During high flow rate (> 25 m/s), the output of the dual-mode sensor is directly digitized by a switched-capacitor incremental delta-sigma ADC with 12-bits resolution due to its large output amplitude. While in low flow rate, the sensor output is first amplified by a capacitively-coupled instrumentation amplifier (CCIA) before digitization. A comparator is employed to enable a dynamic switching between two operation modes based on the flow rate. The readout IC can handle a large input up to 800 mV and consumes a current as low as 114 μA. The simulation results show the measurement system achieves a maximum sensing flow rate of 73 m/s while contributes a maximum measurement error rate of 300 ppm which is considerably lower than the industry standard of 3%.