RKRong-Ming Ko

Rong-Ming Ko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rong-Ming Ko has a total of 109 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Exploiting the Polymorphic Nature of Ga 2 O 3 for High-Performance Sn δ-Doped Power MOSFETs via Multiple Single-Crystalline Layers Engineering

    by Hao-Chun Hung, Fang-Yu Hsu, Chien-Sheng Cheng, Chun-Chia Lin, Kai-Ting Chang, Syuan-Hao Lin, Rong-Ming Ko, Han-Yin Liu, Chin-Sung Lee, Wei-Chou Hsu

  • Open Access

    Low-Leakage and High-Breakdown Enhancement-Mode InAlGaN/GaN HEMTs Using a Non-Recessed Mist-CVD Li-Doped NiO/Al 2 O 3 p-Gate Stack

    by Yan-Kuei Wu, Yu-Hsuan Chen, Hao-Chun Hung, Rong-Ming Ko, Wei-Chou Hsu

    Enhancement-mode (E-mode) InAlGaN/GaN high-electron-mobility transistors (HEMTs) are highly desirable for fail-safe power and RF applications; however, achieving stable normally-off operation without inducing plasma damage remains challenging due to the strong polarization effects in InAlGaN barriers. In this work, non-recessed E-mode InAlGaN/GaN HEMTs enabled by a mist chemical vapor deposition (mist-CVD)–grown Li-doped NiO/Al2O3 p-gate stack are demonstrated. The Al2O3 interlayer serves as a low-damage interface buffer and leakage-suppression dielectric, while the p-type Li-doped NiO layer provides active electrostatic modulation to effectively deplete the polarization-induced two-dimensional electron gas without gate recessing. Compared with undoped p-NiO and Al2O3-only gate configurations, the Li-doped NiO (p-Li:NiO) device exhibits clear enhancement-mode operation with the threshold voltage shifting from −2.36 V to +0.32 V. A high maximum transconductance of 498 mS/mm and an increased saturation drain current of 523 mA/mm are achieved, together with a substantially suppressed gate leakage current of 9.8 × 10-9 mA/mm at VG = −10 V. Moreover, the p-Li:NiO-gated HEMT demonstrates an exceptional off-state breakdown voltage of 2423 V (ID = 1 nA/mm), resulting in a Baliga’s figure of merit of 2.14 GW/cm2. Long-term DC bias stress measurements up to 15,000 s reveal minimal drain-current degradation and excellent threshold-voltage stability, confirming the robustness of the proposed gate stack. These results establish mist-CVD Li-doped NiO/ Al2O3 p-gate engineering as a reliable and process-compatible solution for high-performance, non-recessed enhancement-mode InAlGaN/GaN HEMTs targeting next-generation GaN power electronic applications.


  • Effect of Mg Doping on β -Ga 2 O 3 UVC Photodetectors Deposited by Ultrasonic Spray Pyrolysis

    by Shun-Cheng Shih, Chien-Sheng Cheng, Han-Yin Liu, Hao-Chun Hung, Rong-Ming Ko, Wei-Chou Hsu

    This study investigates a comparative analysis of metal–semiconductor–metal (MSM) photodetectors (PDs) based on β-Ga₂O₃ thin films with varying levels of Mg doping. Thin films with Mg / (Mg + Ga) ratios of 0%, 5%, and 10% were deposited on c-plane sapphire substrates using ultrasonic spray pyrolysis deposition (USPD). Structural, chemical, optical, and morphological properties were systematically characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV–visible (UV–Vis) spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and photoluminescence (PL) spectroscopy. Results indicate that increasing Mg doping level significantly reduces the oxygen vacancy concentration and improves the surface smoothness, while simultaneously widening the optical bandgap from 4.82 to 5.25 eV. Device measurements show that the PD based on 5% Mg-doped β-Ga₂O₃ achieved the highest photoresponsivity of 2.54 × 10⁴ A/W. In contrast, the 10% Mg-doped PD exhibited the lowest dark current (1.1 × 10⁻¹¹ A), along with a high photo-to-dark current ratio (PDCR) of 4.4 × 10⁶, a UV-to-visible rejection ratio of 4.8 × 104, and a detectivity of 1.4 × 10¹⁷ Jones. These findings demonstrate strong potential of USPD-grown Mg-doped β-Ga₂O₃ thin films for next-generation UVC PDs.


  • High-Performance UV Photodetectors Based on Mg Doping Mixed α/ε Mg:Ga 2 O 3 Thin Films Prepared by Mist-CVD

    by Chien-Sheng Cheng, Hao-Chun Hung, Shun-Cheng Shih, Han-Yin Liu, Rong-Ming Ko, Wen-Chau Liu, Wei-Chou Hsu

    This study investigates the impact of Mg doping on α/ε-Ga2O3 thin films for ultraviolet photodetectors (UV-PDs), focusing on phase stabilization, defect suppression, and optoelectronic enhancement. Through phase engineering, a vertically stacked α/ε-phase structure was formed, integrating the stability of α-Ga2O3 and the strong UV absorption of ε-Ga2O3 for enhanced photodetector performance. Mg incorporation plays a dual role: it stabilizes the mixed-phase configuration and modulates the defect landscape by suppressing oxygen vacancies and introducing gain-contributing acceptor states. This combination of structural and defect engineering significantly improves carrier dynamics and contributes to enhanced sensitivity, selectivity, and long-term reliability. The resulting Mg:Ga2O3 devices exhibit an ultralow dark current of 8.0×10-13 A, a photo-to-dark current ratio of 2.9×107, and a high responsivity of 9,475 A/W at 220 nm—representing nearly an order-of-magnitude improvement over undoped counterparts. The external quantum efficiency reaches 5.3×106 %, and long-term stability is confirmed with negligible degradation after 600 days of ambient storage. These findings demonstrate that phase-engineered Mg:Ga2O3 offers a robust and scalable platform for high-performance deep-UV detection.


  • Fabrication of β-Ga₂O₃ Schottky Photodetectors With ε-Ga₂O₃ Cap Layer via Temperature-Lowering Process Mist-CVD Heteroepitaxy

    by Hao-Chun Hung, Chia-Cheng Hsu, Ching-Yu Cheng, Yin-Chu Hsiao, Chien-Sheng Cheng, Rong-Ming Ko, Han-Yin Liu, Wei-Chou Hsu

    In this study, high-performance single-crystal gallium oxide (Ga2O3) stack Schottky photodiodes were successfully fabricated using a mist chemical vapor deposition (mist-CVD) process with a temperature-lowering process. By combining X-ray diffraction and electrical analysis, it was found that the low-temperature growth of the cap layer induces a phase transition of β-Ga2O3 epitaxially grown on the c plane to the ε-type. This transition provides the device with a higher energy barrier and excellent photodetection performance. The single-crystal unintentionally doped (UID) ε-Ga2O3 cap layer and single-crystal β-Ga2O3:Sn stacked on c plane sapphire substrates exhibited notable photoresponse properties (Rλ = 448.41 A/W). Compared to Schottky photodiodes with a UID β-Ga2O3 cap layer and β-Ga2O3:Sn stack, the ε-Ga2O3-based device demonstrates a higher effective Schottky barrier high (0.84 eV), superior rectification characteristics (2.02 × 106), a higher photocurrent-to-dark current ratio (PDCR = 4.12 × 104), and shorter rise and fall response times (tr/tf = 2.4/9.8 s). The Ga2O3 photodiode fabricated using this method achieves higher performance without the need for another additional material stacking, indicating its potential for significant research and application value in the future.


  • Open Access

    Improved Resistive Switching Characteristics by O2 Plasma Treatment in Tri-Layer HfO2/Al2O3/HfO2 RRAM

    by Shyh-Jer Huang, Wei-Hsuan Hsieh, Rong-Ming Ko, Zi-Hao Wang, Yan-Kuin Su

    In this study, a tri-layer HfO2/Al2O3/HfO2 (7/6/7 nm) structure was fabricated using a cost-effective RF sputtering process and treated with oxygen plasma to serve as the resistive switching (RS) active layer for RRAM devices. Compared with a single-layer HfO2 and an untreated tri-layer structure, the oxygen plasma-treated device exhibited significantly enhanced performance. These improvements include a higher ON/OFF current ratio, extended endurance exceeding 1600 cycles, and stable retention beyond 104 seconds. Furthermore, multilevel resistive switching behavior was reliably demonstrated by modulating the compliance current. The results highlight the effectiveness of oxygen plasma treatment in improving switching uniformity and electrical stability, while maintaining a scalable and industry-friendly fabrication process. This work underscores the potential of plasma-treated tri-layer structures for high-density, multilevel non-volatile memory applications.


  • Heteroepitaxial Growth of Sn δ-Doped β-Ga₂O₃ MOSFETs on c-Plane Sapphire via Nonvacuum Mist-CVD Process

    by Hao-Chun Hung, Yin-Chu Hsiao, Ching-Yu Cheng, Chia-Cheng Hsu, Fang-Yu Hsu, Rong-Ming Ko, Han-Yin Liu, Wei-Chou Hsu

    The heteroepitaxy process for growing thin films of single crystal β-phase gallium oxide (β-Ga2O3) on c-plane sapphire substrates was conducted using nonvacuum process mist-chemical vapor deposition. The Sn delta (δ)-doping technique was employed to improve the doping concentration, output current, and gate controllability. The use of tetramethylammonium hydroxide (TMAH) to treat the surface of β-Ga2O3 results in improving the surface morphology, which reduces contact resistance between the source/drain electrode and β-Ga2O3. Experimental results show that the β-Ga2O3 MOSFET with Sn δ-doped layer exposed for 80 s and treatment with TMAH for 5 min proposed in this work exhibit excellent electrical properties, including VTH of -7.5 V, IDS,max of 3.71 mA/mm, a subthreshold swing (SS) of 313.26 mV/dec, Ron,sp of 0.6 Ω⋅cm2, an OFF-state breakdown voltage of 1085 V, and a power figure of merit (PFOM) of 1.96 MW/cm2.


  • A Study of Different Annealing Ambiences on the Performance of ZnGa2O4 UVC Photodetectors by Ultrasonic Spray Pyrolysis Deposition

    by Shun-Cheng Shih, Chung-Yu Guo, Han-Yin Liu, Rong-Ming Ko, Wei-Chou Hsu

    This study presents ZnGa 2 O 4 thin films are prepared on c-plane sapphire by ultrasonic spray pyrolysis deposition and post deposition annealing techniques. The post-annealing process was carried out at temperature of 800 °C in various ambiences, such as oxygen, nitrogen, and air. A systematic analysis was conducted on the material properties, such as crystalline quality and optical performance of ZnGa 2 O 4 thin films after annealing. The material analyses indicate that the crystallinity, surface roughness, oxygen vacancy, and energy bandgap of the ZnGa 2 O 4 were significantly improved through annealing. The ZnGa 2 O 4 photodetector annealed at air shows the largest photo/dark current ratio of ~10 6 and a high maximum responsivity of 24.7 A/W at a wavelength of 240 nm and bias of 5 V. These results suggest that the potential of spinel ZnGa 2 O 4 thin films in applications of UVC detection.


  • Open Access

    Using thin-film transistor with thick oxygen-doped Si–Zn–Sn–O channel and patterned Pt/NiO capping layer to enhance ultraviolet light sensing performance

    by Rong-Ming Ko, Shui-Jinn Wang, Yu-Hao Chen, Chang-Yu Liao, Chien-Hung Wu

    Improving the photodetection performance of thin-film transistor (TFT)-based UV photodetectors (UVPDs), using thick channel layers to promote photocurrent (I ph) or using thin channel layers to suppress dark current (I dark) is typically a trade-off. In this work, UVPDs based on oxygen-doped Si-Zn-Sn-O (SZTO) TFT with a stack of Pt/NiO capping layers (CLs) to release the trade-off between I dark and I ph are demonstrated. The Pt CL creates a wide depletion region in the channel layer to allow the use of thick channels, but still maintains low I dark, while the NiO CL forms a pn heterojunction to provide additional photogenerated carriers and enhance I ph under UV irradiation. Experimental results show that the proposed 95 nm-thick oxygen-doped SZTO TFT with a stack of Pt/NiO dual CLs exhibits an excellent photoresponsivity of 2026 A W−1 and photosensitivity of 9.3 × 107 A A−1, which are about 76× and 82.5× higher than a conventional 45 nm-thick SZTO TFT under 275 nm UV irradiation.


  • Open Access

    Enhancing photodetection performance of UV photodetectors with stacked Pt/NiO dual capping layers on IGZO thin-film transistors

    by Rong-Ming Ko, Shui-Jinn Wang, Sin-Jhih Huang, Chien-Hung Wu, Wei-Han Chen, Hao-Che Cheng

    This paper proposes a solution to mitigate the trade-off between dark and photocurrents in the indium gallium zinc oxide (IGZO) thin-film transistor (TFT) applications, such as ultraviolet photodetectors, by using a stacked Pt/NiO dual capping layer (CL). The Pt CL forms a Schottky contact with the IGZO channel, which maximizes the depletion width on the channel layer and allows the use of a thicker channel to suppress both dark current and channel resistance. On the other hand, the NiO CL forms a pn heterojunction with the IGZO channel, which provides additional space for generating electron–hole pairs and is forward biased by the photovoltaic voltage under UV irradiation, resulting in a further negative shift in the threshold voltage and a significant increase in photocurrent. Experimental results show that the proposed CL scheme exhibits excellent photoresponsivity, photosensitivity, and specific detectivity in a 40 nm-thick IGZO TFT, with the values of 1888 A/W, 3.37 × 108 A/A, and 3.99 × 1016 Jones, respectively, which are about 55%, 83%, and 68% higher than a traditional 30 nm-thick IGZO TFT using only NiO CL under 275 nm UV irradiation.