NFNatalia Mikhailivna Fialko

Natalia Mikhailivna Fialko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Natalia Mikhailivna Fialko has a total of 180 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Increasing fuel efficiency of waste incombustion boiler plants

    by N. M Fialko, R. O Navrodska, S. I Shevchuk, G. O Gnedash, I. M Zhuchenko

    Purpose. The goal is to increasing the thermal efficiency of a water heating boiler burning solid household waste or fuels made from it. Methodology. Known and developed by the authors, methods for thermal calculation of heat exchangers were used. Findings. The modern heat-recovery technology based on the use of a complex system has been proposed for the useful use of waste heat from combustion products of household waste incineration plants and fuels based on it. This system is designed to heat combustion air and heating network water in the corresponding modular heat exchangers-heat recovery units. Original technical solutions for these heat-recovery units have been developed with the possibility of operation on dusty gas flows. Calculation studies have been carried out on the effectiveness of the use of the specified system. The patterns of changes in the main characteristics of the heat-recovery system have been determined, namely: its heat productivity, final temperature levels of the used heat-transfer agents and the volumes of condensate formed during deep cooling of waste gases. The level of flue gas temperature reduction in the entire heat-recovery system is 126.9‒197.1 °C. Therefore, the use of the proposed heat-recovery system and the equipment used is an effective measure to significantly increase the efficiency of incineration of solid household waste and fuels based on it. Originality. First proposed, a complex heat-recovery system designed to heat combustion air and heating water has been proposed for a waste incineration boiler, and its energy efficiency has been investigated. Practical value. The obtained research results will be used to increase the efficiency of incineration of solid household waste and fuels from it in relevant installations.

  • Open Access

    Self-lubricating Composite Nanocoatings Based on Magnesium Reagents

    by Vitaliy Shchepetov, Nataliia Fialko, Constantine Zvorykin

    One area of innovative development is the development of tribotechnical coatings with optimal physical and mechanical properties for specific applications. Magnesium compounds are a promising base material. In particular, the ternary compound of aluminum, magnesium, and boron, which, when further alloyed, forms a composition that provides self-lubricating properties under friction. The aim of this study is to investigate the wear sequences of a composite based on the ternary compound aluminum-magnesium-boron and to investigate the phase composition and structure formation of surface layers capable of self-lubrication. The base material was a ternary compound of aluminum, magnesium, and boron, to which alloyed impurities of titanium, nickel, zirconium, chromium, and other elements were added. The powder mixture for detonation spraying was obtained through mechanochemical synthesis. The tribotechnical properties of the coatings were studied using an end-face method in continuous sliding mode under a constant load. The coating analysis was based on the use of a modern physicochemical analysis system. The developed lubricating coatings are characterized by high antifriction properties and, in terms of operational potential, open up the possibility of using them in the production of modern tribological systems.

  • Open Access

    Revealing the influence of methods for producing polymer micro- and nanocomposites with different polymer matrices on their thermal conductivity properties

    by Nataliia Fialko, Nataliia Meranova, Julii Sherenkovskii, Volodymyr Korzhyk, Roman Serhiienko, Maksym Lazarenko, Sergiy Ryzhkov, Roman Dinzhos

    The thermal conductivity properties of polymer micro- and nanocomposites depending on different production methods have been investigated in this study. The task addressed relates to the synthesis of such composites with a wide range of thermal conductivity properties, the application of which is promising in various fields of science and technology. This task has been solved by performing a set of systematic studies and by conducting corresponding comparative analysis of the results for a wide range of micro- and nanocomposites obtained by different methods. A cycle of experimental studies produced results for composites based on polyvinyl chloride, polyethylene, polypropylene, polycarbonate, and polyamide 6, when filled with carbon nanotubes and microparticles of aluminum and carbon black. When making composites, two methods were used, the first of which is based on mixing components in dry form, the second – in the polymer melt. The dependence of the thermal conductivity properties of composites based on polyvinyl chloride on their production methods was analyzed. It is shown that when using the first of the above methods, relatively low-thermal-conductivity modifications of the studied composites occur, and when using the second method, relatively high values of their thermal conductivity occur. These patterns are explained by the fact that when using the second method, the efficiency of formation of percolation clusters and networks of filler particles is increased, and therefore the thermal conductivity of materials increases. The influence of methods for obtaining composites with different polymer matrices on their thermal conductivity properties was analyzed. Promising areas of application of the proposed composites are power engineering, electric transport, electronics, cooling systems, etc. Their practical use focuses on the latest technologies and equipment

  • Open Access

    BIOETHANOL AS A STRATEGICALLY IMPORTANT FACTOR IN ENERGY AND ENVIRONMENTAL SECURITY OF UKRAINE

    by O.M. Obodovych, O.E. Stepanova, N.M. Fialko

    The article provides a review of literature on the problem of improving motor fuels by adding bioethanol to gasoline with subsequent cavitation treatment of this mixture. A review and analysis of literature data on the processing of lignocellulosic raw materials and its waste into fuel bioethanol and the possibility of its use in a mixture with gasoline for internal combustion engines in the conditions of the Ukrainian economy are conducted. The use of rotary-pulsation devices developed at the Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine for mixing and homogenizing gasoline-alcohol solutions in order to increase their stability and prevent stratification is proposed. The most common is the addition of bioethanol to gasoline in concentrations of 5, 10 and 15 %, which does not affect the operation of the internal combustion engine and allows significantly reducing exhaust emissions. The main difficulty in the production of second-generation bioethanol lies in the conversion of lignocellulosic raw materials, which involves the separation of cellulose, lignin and hemicellulose. The Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine has proposed innovative heat and mass exchange equipment to intensify this process. The other problem of the full use of bioethanol in the preparation of fuel mixtures (gasoline-bioethanol) is their stratification during long-term storage. The literature suggests the use of various types of cavitation devices to solve this problem. The Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine has developed a special design of a rotary-pulsation apparatus (RPA) designed for mixing and homogenizing gasoline-alcohol solutions in order to increase their stability and prevent stratification. Given the important role of bioethanol, it is advisable to adopt legislative initiatives that will have a simultaneous positive effect on several sectors of the economy. This will reduce the state's dependence on energy imports, increase the potential of the agricultural sector, provide additional impetus to the processing industry, and strengthen Ukraine's position in achieving environmental aims.

  • Open Access

    EFFICIENCY OF NEW COMPLEX HEAT-RECOVERY SYSTEMS OF HEATING BOILER UNITS

    by N. Fialko, R. Navrodska, G. Gnedash, S. Shevchuk

    The work is devoted to research on the development and scientific and technical justification of a new heat-recovery system designed to heat return heat-network water and combustion air. At using a traditional system of similar purpose, the heating transfer agent in heat exchangers-heat recovery units is the boiler waste gases. In this case, the water-heating heat-recovery exchanger is installed first in the gas flow, and the air-heating heat-recovery exchanger is installed second. The use of such a scheme for combining heat-recovery exchangers has certain disadvantages. Thus, deep cooling of waste gases with the formation of condensate during the cold period of the heating season is implemented in an air heater, which requires expensive corrosion-resistant materials for its construction. In addition, gas-heating air heaters, as is known, are very large in size, which complicates their placement in the usually cramped conditions of boiler houses. The aim of the work is to develop small-sized and material-intensive complex heat-recovery units for gas-fired eco-efficient heating boilers and to study their efficiency. The main tasks of the work were to develop a new complex heat-recovery system for a heating boiler using a water-heating air heater, devoid of the above-mentioned disadvantages, and to study its efficiency indicators. Known methods of thermal calculation of heating installations and the results of our own research on heat exchange during deep cooling of its metal capacity and compactness under the conditions of operation of eco-efficient boilers with waste gas recirculation were used. The material capacity m and compactness v of the system and its elements were estimated as the ratio of mass or volume to the amount of recovered power of waste gases of boiler installations. The results of the research of the main thermal indicators of the developed system are presented. The patterns of changes in the studied indicators during the heating period are established. The results obtained are compared with those corresponding to the traditional complex heat-recovery system equipped with a gas-heating air heater. It is shown that the use of the proposed system ensures: reliable operation of the air supply channels of the boiler plant due to heating of the combustion air in the water-heating heater of air to 32 ÷ 53 °С, which ensures the absence of condensate formation in these ducts, the resulting increase in the efficiency of the boiler plant of 1.5 ÷ 4.8 % due to the complex use of the recovered heat for heating the heating network water and combustion air, a decrease in the relative metal content of heat exchangers of heat-recovery unit and an increase in their compactness due to the developed heat-exchange surface, which is composed of a bundle of finned bimetallic pipes. In particular, the value of m of the water-heating air heater is 1,9 – 3,2 times smaller than the gas-heating analogue, which ensures a reduction in the total relative metal capacity of the proposed heat-recovery system by 1.4 ÷ 1.7 times, depending on the boiler operating mode and the proportion of waste gas recirculation. Accordingly, the value of the compactness index v is 2.0 ÷ 2.8 times lower for the air heater and 1.6 ÷ 1.9 times lower for the system as a whole.

  • RECIPROCATING GAS ENGINES IN THE DISTRIBUTED ENERGY SECTOR OF UKRAINE

    by A.A. Khalatov, S.G. Kobzar, I.I. Borysov, N.M. Fialko

    The war in Ukraine has posed new challenges for the country's energy sector. The Ukraine's integrated energy sector was built as a centralised system with large hub power plants and a high-voltage power transmission system. This configuration is vulnerable to enemy attacks. It is actually impossible to protect large power plants (especially thermal power plants and combined heat and power plants), and the destruction of these facilities leads to power outages for a large number of consumers. The purpose of this article is to consider the technical and economic aspects of the constructing distributed generation based on gas reciprocating engines to ensure a stable energy supply in Ukraine. Gas engine-based cogeneration systems are truly impressive in terms of their energy-saving capabilities and reduction of noise and vibration levels. Their main advantage is high energy conversion efficiency: compared to separate electricity and heat generation systems, cogeneration systems can save up to 40% of primary energy. Installing such systems in close proximity to consumers significantly reduces energy losses during transmission and distribution. In addition, thanks to low noise and vibration levels, such stations can be located close to end users, making them a convenient solution for urban and industrial areas. Engine exhaust gases have the highest potential. The typical exhaust gas temperature is around 460°C. Exhaust heat can generate medium-pressure steam for purposes such as heating boiler feed water, and low-pressure steam for processes such as sterilisation, pasteurisation, space heating, tank heating, humidification and others. In addition, supplementary combustion with natural gas can increase exhaust gas temperatures and heat transfer, allowing more steam to be produced at higher volumes and pressures, opening up even more possibilities. The modular design means relatively low capital investment in the 1 to 60 MW power range. The frequency and complexity of repairs depend on the type of engine (high- or medium-speed engine, number of cylinders, etc.) and the type of fuel used. In general, the engines are designed for continuous operation for 25–30 years at a rate of 8,000 hours per year, provided that scheduled maintenance and proper technical servicing are carried out. The main types and thermodynamic cycles of engines are analysed, and a comparison with gas turbine installations was made. It was found that a gas turbine is a more efficient solution for a ratio of electrical power to thermal power of less than 0.8. When the ratio of electrical power to thermal power is > ~ 0.8, gas engine systems generally achieve higher overall efficiency and significantly greater primary energy savings. Conclusions. The construction of distributed generation based on gas reciprocating engines allows solving the problem of stability of the Ukrainian energy system in a short time. Modern gas reciprocating engines are capable of operating efficiently on low- and medium-calorific gases, which can be obtained by thermal conversion of local fuels. In general, the development of decentralised energy is one of the main directions in the development of Ukraine's energy sector in the near future. This will increase the stability and reliability of the energy system and improve its ability to function uninterruptedly in wartime and post-war conditions.

  • COMPARATIVE ANALYSIS OF FLOW PATTERNS UNDER ISOTHERMAL CONDITIONS AND COMBUSTION IN MICRO-JET BURNERS WITH MULTI-ROW FUEL SUPPLY

    by N.M. Fialko, A. Klishch, Ju. Sherenkovskyi, N. Meranova, S. Aloshko, D. Gladkov

    The article presents the results of a comparative analysis of isothermal and nonisothermal flow characteristics in stabilizer-type burners with three-row fuel feed, designed for operation at variable excess air ratios. CFD modeling using the FLUENT software package was used as the research method. Simulation experiments were performed using the DDES approach with the Realizable k-є turbulence model. The modeling results revealed significant differences in the flow patterns for the compared situations. These differences include, in particular, the location of high-velocity zones in different regions of the channel. It is shown that the velocity behind the flame stabilizers is generally significantly higher during combustion due to flow acceleration caused by thermal expansion of the gases. This acceleration is found to begin downstream, the farther the gas supply openings are from the stall edge. Particular attention is paid to comparing the characteristics of recirculation zones in the aft region of flame stabilizers, which are responsible for stabilizing the combustion process, for isothermal and nonisothermal flow conditions. It is shown that the extent of these zones increases during combustion, while the maximum absolute velocity values within them decrease. Results are also presented for comparing velocity pulsation fields in the burner devices under study for reacting flows and isothermal flow. It is established that the level of these pulsations during combustion generally significantly exceeds the corresponding level for isothermal flow. The results of these studies can be widely used in selecting the design and operating parameters of the proposed burners.

  • Open Access

    DEVELOPMENT OF METHODS AND TECHNOLOGIES FOR COVERING PEAK LOADS IN THE ENERGY SECTOR OF UKRAINE

    by N.M. Fialko, О.I. Sigal, A.A. Khalatov, D.YU. Paderno, N.O. Meranova, S.V. Plashikhin, Yu.V. Sherenkovskiy

    The article presents the results of the analysis of a number of issues in the context of the problem of covering peak loads in the energy system of Ukraine. Information is provided on the features of the formation of these loads and their changes due to the full-scale invasion of Russia into Ukraine. The corresponding challenges associated with the integration of renewable energy sources into the energy system of Ukraine are considered. The specifics of the implementation of both traditional and innovative approaches to covering peak loads are analyzed, in particular the use of peak generating capacities, energy storage systems, smart grids and demand management, as well as the integration of renewable sources into the energy system in combination with energy storage devices or virtual power plants. The data on the comparison of the characteristics of different types of peak capacities in terms of peak load coverage efficiency are provided. Particular attention is paid to the consideration of the prospects for the development of peak load coverage technologies in Ukraine. It is indicated that in the short term, traditional approaches will have a certain advantage over innovative ones. As for innovative approaches, one of the most promising will be the use of battery systems. Approaches related to demand management and the use of renewable energy sources in combination with energy storage and virtual power plants will remain important. Based on the results of the analysis, a conclusion was made about the growing relevance of the problem of covering peak loads in the energy system of Ukraine, given the increase in these loads due to a number of reasons, including unavoidable ones. Bibl. 44, Fig. 3, Tab. 3.


  • FLOW STRUCTURE DURING COMBUSTION OF NATURAL GAS IN BURNERS WITH A THREE-ROW FUEL SUPPLY SYSTEM

    by N.M. Fialko, Ju. Sherenkovskyi, A. Klishch, N. Meranova, S. Aloshko, O. Martiuk

    The objective of the work is to establish the regularities of the flow of a single gas in micro-jet burner devices with a three-row fuel supply system. The burner devices under consideration are intended for operation under conditions of variable values of the total excess air coefficient, 1.1 ... 1.5. The objective of the study was to determine the effects of the influence of the row number of gas supply holes on various characteristics of the non-isothermal flow in the proposed burners. CFD modeling based on the DES approach was used as a research method. Based on the results of the comparative analysis of the flow characteristics when feeding fuel gas to different rows of gas supply holes, it is shown that these characteristics can significantly depend on the row number of the fuel supply. It was found that with an increase in the row number, the indicators of the recirculation zone behind the flame stabilizer change significantly. The levels of flow rates, velocity pulsations, etc. The research results can be used in the design of micro-flare burners of the stabilizer type.

  • ENSURING RELIABLE OF CHIMNEYS WASTE INCINERATORS WITH EXHAUST HEAT RECOVERY SYSTEMS

    by N. Fialko, R. Navrodska, I Zhuchenko, S. Shevchuk, G. Gnedash

    The work is devoted to research on the development and scientific and technical substantiation of measures to ensure anticorrosion protection of solid waste incineration plants chimneys. The reliability, strength, and durability of these chimneys are essential for the uninterrupted operation of the main equipment of these plants. One of the reasons for the chimneys destruction is a deviation from the design mode of their operation, in particular due to condensation on the internal surfaces of these gas exhaust channels. Among the factors that exacerbate non-compliance with the design conditions of chimneys operation is the use of modern heat recovery technologies that lead to a significant decrease in exhaust gas temperature and a decrease in their velocity in the chimneys. The purpose of the work is to develop and investigate the effectiveness of measures to prevent condensation in the chimneys of a waste incineration heating boiler under conditions of using the deep cooling exhaust gas technology. The main objectives of the work were to determine the efficiency indicators of preventing condensation in the chimney when using the method of reducing heat losses from the chimney hull under conditions of its modification by heat insulation or placement of an insertion gas exhaust pipe; to establish the regularity of changes in the main thermal and humidity indicators at the chimney mouth with the specified modifications when using the air method of preventing condensation in gas exhaust ducts. Known thermal calculation methods of heat installations and the results of our own research into heat exchange during deep cooling of exhaust gases of boiler plants were used. The results of research of the main indicators of the thermal and humidity state (dew point tdp and internal surface temperature ts at the chimney mouth) under the conditions of using combined heat recovery systems and using the method of reducing heat losses from the chimney hull through the specified modifications are presented. It is shown that this method does not prevent the condensate formation at the mouth of the reinforced concrete chimney in all operating modes of the considered boiler during the heating period. Condensation prevention is only realized at negative ambient temperatures corresponding to high boiler heat loads. The regularities of changes in the studied indicators in the case of the combined use of two thermal methods, namely: a) the air method, which consists in mixing a part σ of the air heated in the heat recovery system with the exhaust gases cooled in the heat recovery system; b) the method of reducing heat losses to the environment (by heat insulation of the chimney hull or installing an insertion gas exhaust pipe in it). Based on the analysis results of the studied indicators, it is shown that using these two methods ensures the safe operation of the considered chimney in all boiler modes. At the same time, the part of mixed air σ does not exceed 5 %, and the heat consumption coefficient g for the implementation of the methods is no higher than 5 % of the volume recovered heat.