Martin Claus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Martin Claus has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Stefan Blawid
UFPE
8 shared publications - Anibal Pacheco-Sanchez
Departamento de Electrnica y Tecnologa de Computadores, Universidad de Granada, Granada, Spain
7 shared publications Michael Schroter
Chair for Electron Devices and Integrated Circuits, Dresden University of Technology (TU Dresden), Dresden, Germany
4 shared publications- Sven Mothes
Department of Electrical Engineering and Information Technology, Technische Universität Dresden, Dresden, Germany
4 shared publications - Michael Schröter
Chair for Electron Devices and Integrated Circuits, Technical University Dresden, Dresden, Germany
3 shared publications - Igor Bejenari
Department of Electrical and Computer Engineering Technische Universität Dresden 01062 Germany. I
2 shared publications
Latest Publications
- 12 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4064-4074
Methods for Extracting the Temperature- and Power-Dependent Thermal Resistance for SiGe and III-V HBTs From DC Measurements: A Review and Comparison Across Technologies
Many different methods have been proposed in the literature for the extraction of the thermal resistance of heterojunction bipolar transistors (HBTs). This review presents a detailed evaluation and discussion of several widely used methods. Special emphasis is put on a generalized analysis of the underlying assumptions, suitable operating point range, and necessary measurement effort of each method. The accuracy of each method is determined by applying it to data based on circuit simulations of advanced SiGe and III-V HBT technologies. Experimental data from those technologies are used to highlight practical issues. A guideline for the selection of the most suitable method in practice is also given.
- 12 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4064-4074
Methods for Extracting the Temperature- and Power-Dependent Thermal Resistance for SiGe and III-V HBTs From DC Measurements: A Review and Comparison Across Technologies
Many different methods have been proposed in the literature for the extraction of the thermal resistance of heterojunction bipolar transistors (HBTs). This review presents a detailed evaluation and discussion of several widely used methods. Special emphasis is put on a generalized analysis of the underlying assumptions, suitable operating point range, and necessary measurement effort of each method. The accuracy of each method is determined by applying it to data based on circuit simulations of advanced SiGe and III-V HBT technologies. Experimental data from those technologies are used to highlight practical issues. A guideline for the selection of the most suitable method in practice is also given.
- 22 February 2022
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 9 (1) , 011418
Benchmarking contact quality in N-type organic thin film transistors through an improved virtual-source emission-diffusion model
Due to nonideal behavior, current organic thin film transistor technologies lack the proper models for essential characterization and thus suffer from a poorly estimated parameter extraction critical for circuit design and integration. Organic thin film transistors are often plagued by contact resistance, which is often less problematic in inorganic transistors; consequently, common models used for describing inorganic devices do not properly work with organic thin film transistors. In this work, we fabricate poly{[N,N′-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5′-(2,2′-bithiophene)} based organic thin film transistors with reduced contact resistance through the introduction of metallic interlayers between the semiconductor and gold contacts. The addition of 10 nm thick manganese interlayer provides optimal organic thin film transistor device performance with the lowest level of contact resistance. Improved organic thin film transistors were characterized using an improved organic virtual-source emission diffusion model, which provides a simple and effective method to extract the critical device parameters. The organic virtual-source emission diffusion model led to nearly perfect prediction using effective gate voltages and a gate dependant contact resistance, providing a significant improvement over common metal–oxide–semiconductor field-effect transistor models such as the Shichman–Hodges model.
- 22 February 2022
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 9 (1) , 011418
Benchmarking contact quality in N-type organic thin film transistors through an improved virtual-source emission-diffusion model
Due to nonideal behavior, current organic thin film transistor technologies lack the proper models for essential characterization and thus suffer from a poorly estimated parameter extraction critical for circuit design and integration. Organic thin film transistors are often plagued by contact resistance, which is often less problematic in inorganic transistors; consequently, common models used for describing inorganic devices do not properly work with organic thin film transistors. In this work, we fabricate poly{[N,N′-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5′-(2,2′-bithiophene)} based organic thin film transistors with reduced contact resistance through the introduction of metallic interlayers between the semiconductor and gold contacts. The addition of 10 nm thick manganese interlayer provides optimal organic thin film transistor device performance with the lowest level of contact resistance. Improved organic thin film transistors were characterized using an improved organic virtual-source emission diffusion model, which provides a simple and effective method to extract the critical device parameters. The organic virtual-source emission diffusion model led to nearly perfect prediction using effective gate voltages and a gate dependant contact resistance, providing a significant improvement over common metal–oxide–semiconductor field-effect transistor models such as the Shichman–Hodges model.
- 1 December 2021
- Published by Elsevier in Organic Electronics
- Vol. 99
Impact of injection limitations on the contact resistance and the carrier mobility of organic field effect transistors
- 1 December 2021
- Published by Elsevier in Organic Electronics
- Vol. 99
Impact of injection limitations on the contact resistance and the carrier mobility of organic field effect transistors
- Open Access
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 1 (1) , 275-287
CNTFET Technology for RF Applications: Review and Future Perspective
RF CNTFETs are one of the most promising devices for surpassing incumbent RF-CMOS technology in the near future. Experimental proof of concept that outperformed Si CMOS at the 130 nm technology has already been achieved with a vast potential for improvements. This review compiles and compares the different CNT integration technologies, the achieved RF results as well as demonstrated RF circuits. Moreover, it suggests approaches to enhance the RF performance of CNTFETs further to allow more profound CNTFET based systems e.g., on flexible substrates, highly dense 3D stacks, heterogeneously combined with incumbent technologies or an all-CNT system on a chip.
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 1 (1) , 275-287
Open AccessCNTFET Technology for RF Applications: Review and Future Perspective
RF CNTFETs are one of the most promising devices for surpassing incumbent RF-CMOS technology in the near future. Experimental proof of concept that outperformed Si CMOS at the 130 nm technology has already been achieved with a vast potential for improvements. This review compiles and compares the different CNT integration technologies, the achieved RF results as well as demonstrated RF circuits. Moreover, it suggests approaches to enhance the RF performance of CNTFETs further to allow more profound CNTFET based systems e.g., on flexible substrates, highly dense 3D stacks, heterogeneously combined with incumbent technologies or an all-CNT system on a chip.
- 3 April 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (5) , 055027
Multi-mode nanoFETs: From low power to high performance on demand
Dynamic power management at the lowest design level of electronic hardware, i.e. at the device or transistor level, is still a novelty. Instead, energy saving is usually achieved at the circuit level by switching off high performance components and activating low leakage transistors in the current paths. We discuss here performance projections of field-effect transistors providing multiple power modes. A multi-mode (mm) FET can be configured from GHz performance to ultralow leakage by adjusting the charge injection into the transistor channel between thermionic and band-to-band tunnel injection. Nanodevices with ultrathin doping-free channels are the enabler of this novel device concept that requires excellent electrostatic control of the charge type and density. Moreover, nanomaterials with charge carriers of low effective mass will improve the mode tuning of mmFETs. TCAD simulations show that the device current can be switched through nine orders of magnitude at a supply voltage of 0.5 V . The mmFET can also operate in a low dynamic power mode with reduced drive currents but delay times that still allow sub-MHz operation. These properties make mmFETs a promising technology for low power circuitry supplied only by energy harvesters. The possibility to further decrease the supply voltage by integrating a ferroelectric layer in the capacitor stack is also addressed.
- 3 April 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (5) , 055027
Multi-mode nanoFETs: From low power to high performance on demand
Dynamic power management at the lowest design level of electronic hardware, i.e. at the device or transistor level, is still a novelty. Instead, energy saving is usually achieved at the circuit level by switching off high performance components and activating low leakage transistors in the current paths. We discuss here performance projections of field-effect transistors providing multiple power modes. A multi-mode (mm) FET can be configured from GHz performance to ultralow leakage by adjusting the charge injection into the transistor channel between thermionic and band-to-band tunnel injection. Nanodevices with ultrathin doping-free channels are the enabler of this novel device concept that requires excellent electrostatic control of the charge type and density. Moreover, nanomaterials with charge carriers of low effective mass will improve the mode tuning of mmFETs. TCAD simulations show that the device current can be switched through nine orders of magnitude at a supply voltage of 0.5 V . The mmFET can also operate in a low dynamic power mode with reduced drive currents but delay times that still allow sub-MHz operation. These properties make mmFETs a promising technology for low power circuitry supplied only by energy harvesters. The possibility to further decrease the supply voltage by integrating a ferroelectric layer in the capacitor stack is also addressed.
- 1 January 2020
- Published by Elsevier in Solid-State Electronics
- Vol. 163
Understanding the metal-oxides induced reduction of the contact resistance in organic transistors
- 1 January 2020
- Published by Elsevier in Solid-State Electronics
- Vol. 163
Understanding the metal-oxides induced reduction of the contact resistance in organic transistors
- 16 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 19 (1536125X) , 47-51
Bias-Dependent Contact Resistance Characterization of Carbon Nanotube FETs
An extraction method for a bias-dependent contact resistance is presented and applied to simulation and experimental data of single- and multi-tube carbon nanotube field effect-transistors with different channel lengths and Schottky barrier heights. The method relies on the individual device characteristics and there is no need of fabrication of test structures or challenging model calibration. The extracted values correspond to reference values in the simulations and are as well similar to the ones obtained for the fabricated devices with other analytical and physics-based approaches. However, by revealing the bias-dependence of the extracted contact parameters it enables a characterization of the Schottky barriers at the contacts in more detail.
- 16 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 19 (1536125X) , 47-51
Bias-Dependent Contact Resistance Characterization of Carbon Nanotube FETs
An extraction method for a bias-dependent contact resistance is presented and applied to simulation and experimental data of single- and multi-tube carbon nanotube field effect-transistors with different channel lengths and Schottky barrier heights. The method relies on the individual device characteristics and there is no need of fabrication of test structures or challenging model calibration. The extracted values correspond to reference values in the simulations and are as well similar to the ones obtained for the fabricated devices with other analytical and physics-based approaches. However, by revealing the bias-dependence of the extracted contact parameters it enables a characterization of the Schottky barriers at the contacts in more detail.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 18 (1536125X) , 345-350
Practical Mobility Estimations for Transistors With 1-D Channels Based on the Landauer–Büttiker Equation
Practical mobility expressions are derived for transistors with one-dimensional (1D) semiconductors in the channel such as carbon nanotubes (CNTs) based on the 1D Landauer-Buttiker equation covering the ballistic as well as the non-ballistic transport regime. By decomposing the impact of serial resistances capturing the voltage drops across the metal-CNT interfaces and the supply lines as well as the impact associated with the quantum resistance, definitions for the mobility have been derived allowing a meaningful evaluation of the semiconductor material. The definitions involve measurable quantities in contrast to previous publications with hidden quantities and they are applied to synthetic and experimental data of single-tube CNT field-effect transistors of different channel lengths, Schottky barrier heights, diameters and doping. Peak extracted mobility values agree with results from a physics-based diameter-dependent mobility model. The length-independent channel mobility obtained in this work is a useful parameter for technology evaluation, especially for short channel devices.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 18 (1536125X) , 345-350
Practical Mobility Estimations for Transistors With 1-D Channels Based on the Landauer–Büttiker Equation
Practical mobility expressions are derived for transistors with one-dimensional (1D) semiconductors in the channel such as carbon nanotubes (CNTs) based on the 1D Landauer-Buttiker equation covering the ballistic as well as the non-ballistic transport regime. By decomposing the impact of serial resistances capturing the voltage drops across the metal-CNT interfaces and the supply lines as well as the impact associated with the quantum resistance, definitions for the mobility have been derived allowing a meaningful evaluation of the semiconductor material. The definitions involve measurable quantities in contrast to previous publications with hidden quantities and they are applied to synthetic and experimental data of single-tube CNT field-effect transistors of different channel lengths, Schottky barrier heights, diameters and doping. Peak extracted mobility values agree with results from a physics-based diameter-dependent mobility model. The length-independent channel mobility obtained in this work is a useful parameter for technology evaluation, especially for short channel devices.
- 18 December 2017
- Published by IOP Publishing in Nanotechnology
- Vol. 29 (3) , 035203
Polymer-based doping control for performance enhancement of wet-processed short-channel CNTFETs
The electrical transport properties of short-channel transistors based on single-walled carbon nanotubes (CNT) are significantly affected by bundling along with solution processing. We report that especially high off currents of CNT transistors are not only related to the incorporation of metallic CNTs but also to the incorporation of CNT bundles. By applying device passivation with poly(4-vinylpyridine), the impact of CNT bundling on the device performance can be strongly reduced due to increased gate efficiency as well as reduced oxygen and water-induced p-type doping, boosting essential field-effect transistor performance parameters by several orders of magnitude. Moreover, this passivation approach allows the hysteresis and threshold voltage of CNT transistors to be tuned.
- 18 December 2017
- Published by IOP Publishing in Nanotechnology
- Vol. 29 (3) , 035203
Polymer-based doping control for performance enhancement of wet-processed short-channel CNTFETs
The electrical transport properties of short-channel transistors based on single-walled carbon nanotubes (CNT) are significantly affected by bundling along with solution processing. We report that especially high off currents of CNT transistors are not only related to the incorporation of metallic CNTs but also to the incorporation of CNT bundles. By applying device passivation with poly(4-vinylpyridine), the impact of CNT bundling on the device performance can be strongly reduced due to increased gate efficiency as well as reduced oxygen and water-induced p-type doping, boosting essential field-effect transistor performance parameters by several orders of magnitude. Moreover, this passivation approach allows the hysteresis and threshold voltage of CNT transistors to be tuned.
- 7 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (6) , 704-708
Projected Tolerances of Carbon Nanotube Current-Mode Logic to Process Variability
Radio frequency (RF) analog applications present an interesting opportunity for carbon nanotube (CNT) based electronics. Extrinsic peak operating frequencies of up to 40 GHz for CNTFETs manufactured on wafer scale employing very moderate dimensions have been already demonstrated. However, as in any emergent technology, variability of the fabricated devices is significant. Therefore, predictions about the behavior of benchmark circuits at the process corners are required to further stimulate complex RF design and fabrication. We report here on the projected tolerance of a current-mode logic (CML) buffer/inverter designed for 2.4GHz (5 Gbit s⁻¹), 1.8V supply voltage, 1.8 tail current and a 600mV voltage swing. The single CML stage is very robust against variations in CNT density but vulnerable to source-drain shorts introduced by metallic tubes in the channel. A corresponding five-stage CML ring oscillator shows considerably reduced output voltage swing beyond two percent metallic tube fraction indicating the importance of metallic tube reduction by technology dependent strategies like pre-sorting, post-elimination or type-selective growth.
- 7 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (6) , 704-708
Projected Tolerances of Carbon Nanotube Current-Mode Logic to Process Variability
Radio frequency (RF) analog applications present an interesting opportunity for carbon nanotube (CNT) based electronics. Extrinsic peak operating frequencies of up to 40 GHz for CNTFETs manufactured on wafer scale employing very moderate dimensions have been already demonstrated. However, as in any emergent technology, variability of the fabricated devices is significant. Therefore, predictions about the behavior of benchmark circuits at the process corners are required to further stimulate complex RF design and fabrication. We report here on the projected tolerance of a current-mode logic (CML) buffer/inverter designed for 2.4GHz (5 Gbit s⁻¹), 1.8V supply voltage, 1.8 tail current and a 600mV voltage swing. The single CML stage is very robust against variations in CNT density but vulnerable to source-drain shorts introduced by metallic tubes in the channel. A corresponding five-stage CML ring oscillator shows considerably reduced output voltage swing beyond two percent metallic tube fraction indicating the importance of metallic tube reduction by technology dependent strategies like pre-sorting, post-elimination or type-selective growth.