Ibrahim Kutay Yilmazcoban
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ibrahim Kutay Yilmazcoban has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Fatih Balıkoğlu
Mechanical Engineering , Balikesir University , Balikesir , Türkiye
3 shared publications - Kaan Ferikel
Mechanical Engineering , 52992 Sakarya University , Sakarya , Türkiye
3 shared publications Abdullah Mimaroglu
Sakarya University, Engineering Faculty, Mechanical Eng. Dept., Esentepe Campus, 54187 Sakarya, Turkey
2 shared publications- Ahmet Cagatay Cilingir
Sakarya University, Faculty of Engineering
2 shared publications - Can Çivi
Celal Bayar Üniversitesi
2 shared publications - Mehmet Özer
BALIKESIR UNIVERSITY, BİGADİÇ VOCATIONAL SCHOOL, DEPARTMENT OF TRANSPORTATION SERVICES
2 shared publications
Latest Publications
- Open Access
The Bending Impact of the Failure Investigation of the Polymer-Reinforced Composite Protection Bars
It is well established that an anti-intrusion beam is a passive safety system that serves an essential role for passengers during collisions. In this study, the influence of internal reinforcements on the bending failure of a cylindrical aluminum tube was systematically investigated through a series of composite beam tests. Polymeric materials, including cast polyamide (PA6) and polypropylene (PP), with varying wall thicknesses, were deemed suitable for use as the inner reinforcement of the Al 6063-T6 tube. The test setup, which simulates impact conditions experienced by structural components in full-scale crash tests, is a powerful tool for the bending impacts in the study. To describe the connection between bending impact and quasi-static loading of composite beams, each method is compared to clarify the composite’s failure behavior. An explicit Finite Element Analysis (FEA) of impact scenarios has been performed to understand the deformation behavior of polymer-reinforced composites and to determine the absorbed impact energy, thereby clarifying which specimen is better able to absorb bending impact energy. Primarily, three polymer-reinforced specimens were accepted with a hollow Al tube. After initial tests and simulations, the expected parametric study could not be achieved except for one. Then, three more combinations were offered. For one of the three specimens, the thickness of the central reinforcement PP was increased until a fully developed shaft was produced, resulting in better-than-expected bending impact-absorbing performance. The results indicate that the energy level of the inner reinforcements with polymeric materials increased 8.8 times, to about 750 J, compared to the plain Al tube (85 J) under bending impact loads. The numerical simulations are relevant and reliable for the details of the specimens’ impact process and show good agreement with the experimental results. Finally, depending on the content, this research, rather than focusing on the fundamental concept of polymer-reinforced aluminum crash tubes, focuses on the specific dynamic bending impact evaluation of the Al, PA6, and PP configuration and the design insight that hollow PP reinforcement can accelerate fracture. In contrast, a fully filled PP core inside a PA6 sleeve can suppress splitting and substantially improve impact energy absorption.
Open AccessThe Bending Impact of the Failure Investigation of the Polymer-Reinforced Composite Protection Bars
It is well established that an anti-intrusion beam is a passive safety system that serves an essential role for passengers during collisions. In this study, the influence of internal reinforcements on the bending failure of a cylindrical aluminum tube was systematically investigated through a series of composite beam tests. Polymeric materials, including cast polyamide (PA6) and polypropylene (PP), with varying wall thicknesses, were deemed suitable for use as the inner reinforcement of the Al 6063-T6 tube. The test setup, which simulates impact conditions experienced by structural components in full-scale crash tests, is a powerful tool for the bending impacts in the study. To describe the connection between bending impact and quasi-static loading of composite beams, each method is compared to clarify the composite’s failure behavior. An explicit Finite Element Analysis (FEA) of impact scenarios has been performed to understand the deformation behavior of polymer-reinforced composites and to determine the absorbed impact energy, thereby clarifying which specimen is better able to absorb bending impact energy. Primarily, three polymer-reinforced specimens were accepted with a hollow Al tube. After initial tests and simulations, the expected parametric study could not be achieved except for one. Then, three more combinations were offered. For one of the three specimens, the thickness of the central reinforcement PP was increased until a fully developed shaft was produced, resulting in better-than-expected bending impact-absorbing performance. The results indicate that the energy level of the inner reinforcements with polymeric materials increased 8.8 times, to about 750 J, compared to the plain Al tube (85 J) under bending impact loads. The numerical simulations are relevant and reliable for the details of the specimens’ impact process and show good agreement with the experimental results. Finally, depending on the content, this research, rather than focusing on the fundamental concept of polymer-reinforced aluminum crash tubes, focuses on the specific dynamic bending impact evaluation of the Al, PA6, and PP configuration and the design insight that hollow PP reinforcement can accelerate fracture. In contrast, a fully filled PP core inside a PA6 sleeve can suppress splitting and substantially improve impact energy absorption.
- Open Access
- 19 March 2026
- Published by MDPI AG in Preprints.org
The Bending Impact of the Failure Investigation of the Polymer-Reinforced Composite Protection Bars
It is well established that an anti-intrusion beam is a passive safety system that serves an essential role for passengers during collisions. In this study, the influence of internal reinforcements on the bending failure of a cylindrical aluminum tube was systematically investigated through a series of composite beam tests. Polymeric materials, including cast polyamide (PA6) and polypropylene (PP), with varying wall thicknesses, were deemed suitable for use as the inner reinforcement of the Al 6063-T6 tube. The test setup, which simulates impact conditions experienced by structural components in full-scale crash tests, is a powerful tool for the bending impacts in the study. To describe the connection between bending impact and quasi-static loading of composite beams, each method is compared to clarify the composite’s failure behavior. An explicit Finite Element Analysis (FEA) of impact scenarios has been performed to understand the deformation behavior of polymer-reinforced composites and to determine the absorbed impact energy, thereby clarifying which specimen is better able to absorb bending impact energy. Primarily, 3 polymer-reinforced specimens were accepted with a hollow Al tube. After initial tests and simulations, the expected optimization could not be achieved except for one. Then, 3 more combinations were offered. For one of the three specimens, the thickness of the central reinforcement PP was increased until a fully developed shaft was produced, resulting in better-than-expected bending impact-absorbing performance. The results indicate that the energy level of the inner reinforcements with polymeric materials increased 8.8 times, to about 750 J, compared to the plain Al tube (85J) under bending impact loads. The numerical simulations are relevant and reliable for the details of the specimens’ impact process and show good agreement with the experimental results. Finally, depending on the content, this research, rather than focusing on the fundamental concept of polymer-reinforced aluminum crash tubes, focuses on the specific dynamic bending-impact evaluation of the Al, PA6, and PP configuration and the design insight that hollow PP reinforcement can accelerate fracture. In contrast, a fully filled PP core inside a PA6 sleeve can suppress splitting and substantially improve impact energy absorption.
- 19 March 2026
- Published by MDPI AG in Preprints.org
Open AccessThe Bending Impact of the Failure Investigation of the Polymer-Reinforced Composite Protection Bars
It is well established that an anti-intrusion beam is a passive safety system that serves an essential role for passengers during collisions. In this study, the influence of internal reinforcements on the bending failure of a cylindrical aluminum tube was systematically investigated through a series of composite beam tests. Polymeric materials, including cast polyamide (PA6) and polypropylene (PP), with varying wall thicknesses, were deemed suitable for use as the inner reinforcement of the Al 6063-T6 tube. The test setup, which simulates impact conditions experienced by structural components in full-scale crash tests, is a powerful tool for the bending impacts in the study. To describe the connection between bending impact and quasi-static loading of composite beams, each method is compared to clarify the composite’s failure behavior. An explicit Finite Element Analysis (FEA) of impact scenarios has been performed to understand the deformation behavior of polymer-reinforced composites and to determine the absorbed impact energy, thereby clarifying which specimen is better able to absorb bending impact energy. Primarily, 3 polymer-reinforced specimens were accepted with a hollow Al tube. After initial tests and simulations, the expected optimization could not be achieved except for one. Then, 3 more combinations were offered. For one of the three specimens, the thickness of the central reinforcement PP was increased until a fully developed shaft was produced, resulting in better-than-expected bending impact-absorbing performance. The results indicate that the energy level of the inner reinforcements with polymeric materials increased 8.8 times, to about 750 J, compared to the plain Al tube (85J) under bending impact loads. The numerical simulations are relevant and reliable for the details of the specimens’ impact process and show good agreement with the experimental results. Finally, depending on the content, this research, rather than focusing on the fundamental concept of polymer-reinforced aluminum crash tubes, focuses on the specific dynamic bending-impact evaluation of the Al, PA6, and PP configuration and the design insight that hollow PP reinforcement can accelerate fracture. In contrast, a fully filled PP core inside a PA6 sleeve can suppress splitting and substantially improve impact energy absorption.
- Open Access
- 23 January 2026
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (4) , 700-714
Ballistic performance of multi-layered armor combinations under 7.62 × 51 mm FMJ bullet impact
This work performed a nonlinear numerical analysis of Armox 500T and Hardox 450 armor steels, Kevlar 29/epoxy laminate, and aluminum honeycomb materials under ballistic conditions, validating the results via experimental data. The ballistic performance of 20 distinct armor configurations was investigated, including monolithic steel, steel-composite, and steel-composite-honeycomb panels produced by various material arrangements. Ballistics tests were conducted using 7.62 × 51 mm full metal jacket bullets with a muzzle velocity of 838 ± 15 m s −1 under the NIJ 0108.01 III protection level standard. The effect of Kevlar29/epoxy layer thickness in multi-layered panels was examined extensively. The results showed that the ballistic performance of the composite armors was significantly improved due to the combination of monolithic steel plates with Kevlar 29/epoxy and aluminum honeycomb layers. Steel-Kevlar 29/epoxy and steel-Kevlar 29/epoxy-honeycomb multi-layered plates provide identical ballistic protection to monolithic steel counterparts while being 51 wt.% and 57 wt.% lighter than monolithic steel armor. Comprehensive finite element simulations of the ballistic impact events were conducted to elucidate the phenomena of defeat and penetration with greater precision.
- 23 January 2026
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (4) , 700-714
Open AccessBallistic performance of multi-layered armor combinations under 7.62 × 51 mm FMJ bullet impact
This work performed a nonlinear numerical analysis of Armox 500T and Hardox 450 armor steels, Kevlar 29/epoxy laminate, and aluminum honeycomb materials under ballistic conditions, validating the results via experimental data. The ballistic performance of 20 distinct armor configurations was investigated, including monolithic steel, steel-composite, and steel-composite-honeycomb panels produced by various material arrangements. Ballistics tests were conducted using 7.62 × 51 mm full metal jacket bullets with a muzzle velocity of 838 ± 15 m s −1 under the NIJ 0108.01 III protection level standard. The effect of Kevlar29/epoxy layer thickness in multi-layered panels was examined extensively. The results showed that the ballistic performance of the composite armors was significantly improved due to the combination of monolithic steel plates with Kevlar 29/epoxy and aluminum honeycomb layers. Steel-Kevlar 29/epoxy and steel-Kevlar 29/epoxy-honeycomb multi-layered plates provide identical ballistic protection to monolithic steel counterparts while being 51 wt.% and 57 wt.% lighter than monolithic steel armor. Comprehensive finite element simulations of the ballistic impact events were conducted to elucidate the phenomena of defeat and penetration with greater precision.
- 3 December 2024
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 27 (4) , 1621-1632
HARDOX 450, ALUMİNYUM BALPETEĞİ VE ARAMİD/EPOKSİ TABAKALI HİBRİT ZIRH PLAKALARININ BALİSTİK DAVRANIŞININ İNCELENMESİ
Bu çalışmada, Hardox 450 çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinden oluşan tekli ve çoklu hibrit zırh yapılarının balistik performansı araştırılmıştır. Test levhalarına 833 ± 15 m/s namlu çıkış hızına sahip 7.62 tam metal kaplama mermi ile deneysel balistik testler gerçekleştirilmiştir. Balistik test uygulanacak levhalar 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Test levhaları dört kenarından sabitlenmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Deneysel çalışmalarda, vurma yüzeyine göre sırasıyla 4 mm Hardox 450, 24 kat Aramid /epoksi laminat kompozit ve 10 mm Alüminyum bal peteğinden oluşan hibrit zırh yapısı darbe enerjisine balistik direnç gösterememiştir. Öte yandan tekli yapı olarak kullanılan 6 mm Hardox 450 zırh plakası darbe enerjisine balistik direnç sergilemiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmış; arka yüzey çöküntü miktarı ve sönümlenen enerji miktarları karşılaştırmalı olarak verilmiştir.
- 3 December 2024
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 27 (4) , 1621-1632
HARDOX 450, ALUMİNYUM BALPETEĞİ VE ARAMİD/EPOKSİ TABAKALI HİBRİT ZIRH PLAKALARININ BALİSTİK DAVRANIŞININ İNCELENMESİ
Bu çalışmada, Hardox 450 çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinden oluşan tekli ve çoklu hibrit zırh yapılarının balistik performansı araştırılmıştır. Test levhalarına 833 ± 15 m/s namlu çıkış hızına sahip 7.62 tam metal kaplama mermi ile deneysel balistik testler gerçekleştirilmiştir. Balistik test uygulanacak levhalar 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Test levhaları dört kenarından sabitlenmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Deneysel çalışmalarda, vurma yüzeyine göre sırasıyla 4 mm Hardox 450, 24 kat Aramid /epoksi laminat kompozit ve 10 mm Alüminyum bal peteğinden oluşan hibrit zırh yapısı darbe enerjisine balistik direnç gösterememiştir. Öte yandan tekli yapı olarak kullanılan 6 mm Hardox 450 zırh plakası darbe enerjisine balistik direnç sergilemiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmış; arka yüzey çöküntü miktarı ve sönümlenen enerji miktarları karşılaştırmalı olarak verilmiştir.
- Open Access
- 15 September 2024
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 14 (3) , 1176-1191
Armox 500T Zırh Çeliği İçeren Hibrit Zırh Plakalarının 7.62 mm Tam Metal Kaplama Mermi Karşısındaki Balistik Davranışının Deneysel ve Sayısal Olarak Araştırılması
Bu çalışmada, Armox 500T zırh çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinin tekli ve çoklu hibrit zırh yapıları çeşitli kombinasyonlarla bir araya getirilmiş ve balistik performansları araştırılmıştır. Deneysel çalışma, namlu çıkış hızı 847 ± 10 m/s olan 7.62×51 mm tam metal kaplama mermi ile balistik testler gerçekleştirilmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Balistik test levhaları 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmıştır. Deneysel çalışmalarda, monolitik çelik ve hibrit oluşan zırh yapısı balistik koruma sağlamamıştır. Bununla birlikte, metal ve kompozit levhaların hibritleşmesi ile sönümlenen balistik darbe enerji miktarı artırmıştır. Ayrıca, çalışmaya dahil edilen tüm zırh kombinasyonları ağırlık ve kalınlık açısından değerlendirilmiş birbirlerine üstünlükleri belirlenmeye çalışılmıştır. Hibritleşme ile elde edilen enerji sönümleme değerleri, plakaların ağırlığındaki artışa göre daha büyük bir yüzdesel artış sergilemiştir. Zırh kombinasyonlarının sonlu elemanlar analizi neticeleri deneysel veriler ile karşılaştırılması sağlanmış ve iyi uyum gözlemlenmiştir.
- 15 September 2024
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 14 (3) , 1176-1191
Open AccessArmox 500T Zırh Çeliği İçeren Hibrit Zırh Plakalarının 7.62 mm Tam Metal Kaplama Mermi Karşısındaki Balistik Davranışının Deneysel ve Sayısal Olarak Araştırılması
Bu çalışmada, Armox 500T zırh çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinin tekli ve çoklu hibrit zırh yapıları çeşitli kombinasyonlarla bir araya getirilmiş ve balistik performansları araştırılmıştır. Deneysel çalışma, namlu çıkış hızı 847 ± 10 m/s olan 7.62×51 mm tam metal kaplama mermi ile balistik testler gerçekleştirilmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Balistik test levhaları 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmıştır. Deneysel çalışmalarda, monolitik çelik ve hibrit oluşan zırh yapısı balistik koruma sağlamamıştır. Bununla birlikte, metal ve kompozit levhaların hibritleşmesi ile sönümlenen balistik darbe enerji miktarı artırmıştır. Ayrıca, çalışmaya dahil edilen tüm zırh kombinasyonları ağırlık ve kalınlık açısından değerlendirilmiş birbirlerine üstünlükleri belirlenmeye çalışılmıştır. Hibritleşme ile elde edilen enerji sönümleme değerleri, plakaların ağırlığındaki artışa göre daha büyük bir yüzdesel artış sergilemiştir. Zırh kombinasyonlarının sonlu elemanlar analizi neticeleri deneysel veriler ile karşılaştırılması sağlanmış ve iyi uyum gözlemlenmiştir.
- 1 September 2020
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 9 (3) , 935-942
Experimental advancement of filled wood shafts from an inspiration by bone
Considering the enduring mechanical behavior of the lattice structure and compact part of the bone, an analogy between samples made of easily found beechwood and the metacarpal bones of lambs was compared to differentiate their mechanical behaviors, and moreover, to facilitate the beech patterns in various applications with the help of experiments. During the experimental process, beechwood shafts with five different diameters and the same length were tested under three-point bending conditions. Bores inside the beech samples represent the marrow aperture, while the applied polystyrene foam inside the beech samples represents the volume of marrow in a bone. The proposed study presents an investigation of the filled beech shafts by way of three-point bending tests with the biomimetic inspiration of the bone structure to develop passive protection bars for different applications. The experimental results of the filled beech samples were examined to understand the crack and the propagation types by comparing these with the metacarpal bone experiment responses. The proposed investigation approach for the wood specimens subjected to three-point bending conditions is finally discussed, and the advantages are characterized to determine the most reliable beech sample for the protection bars.
- 1 September 2020
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 9 (3) , 935-942
Experimental advancement of filled wood shafts from an inspiration by bone
Considering the enduring mechanical behavior of the lattice structure and compact part of the bone, an analogy between samples made of easily found beechwood and the metacarpal bones of lambs was compared to differentiate their mechanical behaviors, and moreover, to facilitate the beech patterns in various applications with the help of experiments. During the experimental process, beechwood shafts with five different diameters and the same length were tested under three-point bending conditions. Bores inside the beech samples represent the marrow aperture, while the applied polystyrene foam inside the beech samples represents the volume of marrow in a bone. The proposed study presents an investigation of the filled beech shafts by way of three-point bending tests with the biomimetic inspiration of the bone structure to develop passive protection bars for different applications. The experimental results of the filled beech samples were examined to understand the crack and the propagation types by comparing these with the metacarpal bone experiment responses. The proposed investigation approach for the wood specimens subjected to three-point bending conditions is finally discussed, and the advantages are characterized to determine the most reliable beech sample for the protection bars.
- 1 February 2019
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 23 (1) , 76-84
Numerical and experimental approach of various sectioned new concept of the crash-boxes to determine the reliability and crashworthiness of the vehicles during frontal impacts
Araç kazaları incelendiğinde, çarpışma davranışını ve yolcu güvenliğini değerlendirmek hususunda bir perspektif oluşmaktadır. Araç gövdesindeki deformasyonları ve yolcu yaralanmalarını azaltmak için günümüze değin birçok donanım zaten geliştirilmiş bulunmaktadır. Bu donanımlar, aktif ve pasif güvenlik sistemleri olarak ikiye ayrılmaktadır. Bu çalışma, araçların kaza sürecinde çarpışma kutusu adı altında kullanılan pasif güvenlik sistemleri hakkında olup, önden çarpışmalardaki şok etkilerinin azaltılması maksadıyla deneysel olarak incelemelerden oluşmaktadır. Çarpışma kutuları için kare, dairesel ve diğer standart kapalı kesitler imalatın kolaylığı bakımından tercih edilmektedirler. Bu çalışma için ise açık kesitli çarpışma kutuları çalışılmıştır. İmalattaki sınırlandırmalardan dolayı dört yeni tasarımdan bir tanesi tercih edilmiştir. Bu yeni tasarım çarpışma kutusu klasik kullanımdakinden farklı olarak şasi önünde ve ön tamponun hemen arkasında yer almaktadır. W şekilli bir kesite sahip olan çelik sac-metal çarpışma kutusu şok emici bir ünite olarak üretilmiştir. Deneyler için ise 2.88m düşürme yüksekliğine sahip bir test düzeneği kullanılmıştır. Test sürecinde, deney düzeneğinin kapasitesine bağlı olarak 1200kg’ a sahip bir aracın gerçek kaza senaryosunun sekizde biri canlandırabilmektedir. Çarpışma testleri, kabul edilen kaza senaryosunun oranı doğrultusunda 150kg şeklinde olmaktadır. Sönümleyiciler için en uygun sac kalınlığına karar verebilmek maksadıyla 2mm, 1.5mm, 1mm ve 0.8mm kalınlıktaki numuneler kullanılmışlardır. Sonuç olarak ise, 1mm kalınlıktaki St37 malzemeden imal edilmiş w şekilli sac-metal çarpışma kutusunun, önden meydana gelen kazada ortaya çıkan çarpışma enerjisini sönümleyebilecek kadar dayanıklı olduğu anlaşılmıştır.
- 1 February 2019
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 23 (1) , 76-84
Numerical and experimental approach of various sectioned new concept of the crash-boxes to determine the reliability and crashworthiness of the vehicles during frontal impacts
Araç kazaları incelendiğinde, çarpışma davranışını ve yolcu güvenliğini değerlendirmek hususunda bir perspektif oluşmaktadır. Araç gövdesindeki deformasyonları ve yolcu yaralanmalarını azaltmak için günümüze değin birçok donanım zaten geliştirilmiş bulunmaktadır. Bu donanımlar, aktif ve pasif güvenlik sistemleri olarak ikiye ayrılmaktadır. Bu çalışma, araçların kaza sürecinde çarpışma kutusu adı altında kullanılan pasif güvenlik sistemleri hakkında olup, önden çarpışmalardaki şok etkilerinin azaltılması maksadıyla deneysel olarak incelemelerden oluşmaktadır. Çarpışma kutuları için kare, dairesel ve diğer standart kapalı kesitler imalatın kolaylığı bakımından tercih edilmektedirler. Bu çalışma için ise açık kesitli çarpışma kutuları çalışılmıştır. İmalattaki sınırlandırmalardan dolayı dört yeni tasarımdan bir tanesi tercih edilmiştir. Bu yeni tasarım çarpışma kutusu klasik kullanımdakinden farklı olarak şasi önünde ve ön tamponun hemen arkasında yer almaktadır. W şekilli bir kesite sahip olan çelik sac-metal çarpışma kutusu şok emici bir ünite olarak üretilmiştir. Deneyler için ise 2.88m düşürme yüksekliğine sahip bir test düzeneği kullanılmıştır. Test sürecinde, deney düzeneğinin kapasitesine bağlı olarak 1200kg’ a sahip bir aracın gerçek kaza senaryosunun sekizde biri canlandırabilmektedir. Çarpışma testleri, kabul edilen kaza senaryosunun oranı doğrultusunda 150kg şeklinde olmaktadır. Sönümleyiciler için en uygun sac kalınlığına karar verebilmek maksadıyla 2mm, 1.5mm, 1mm ve 0.8mm kalınlıktaki numuneler kullanılmışlardır. Sonuç olarak ise, 1mm kalınlıktaki St37 malzemeden imal edilmiş w şekilli sac-metal çarpışma kutusunun, önden meydana gelen kazada ortaya çıkan çarpışma enerjisini sönümleyebilecek kadar dayanıklı olduğu anlaşılmıştır.
- 1 October 2018
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 22 (5) , 1253-1259
Numerical Analysis of the Lamb Metacarpal Bone: Approximation of Bending Tests
In the development of new strategies for fracture fixation, new methods have to be tested biomechanically under in vitro conditions before clinical trials can be performed. Several recent developments, including tensile, compressive, and bending tests fresh whole bone specimens, offer the possibility to understand animal bones mechanical behavior. Therefore, the aims of the present study were to determine the effects of three point bending tests on the lamb metacarpal bones at different speeds and determine the mechanical properties of bone and to compare these properties with the finite element analysis of the tests. 12 specimens were obtained from 1 year old Ankara curly lambs. Three point bending tests were conducted using three different compression speeds to assess and compare bone fracture properties. From the test results bending moments, stresses, strains and deformations were calculated for three different compression speeds. Finite Element Analysis results were compared to the test results. Because of the use fresh bone specimens of an animal part are used like in vivo tests in biomechanical studies, investigating failure loads of the metacarpus by bending tests and numerical analysis are guiding for clinical operations and computer simulations.
- 1 October 2018
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 22 (5) , 1253-1259
Numerical Analysis of the Lamb Metacarpal Bone: Approximation of Bending Tests
In the development of new strategies for fracture fixation, new methods have to be tested biomechanically under in vitro conditions before clinical trials can be performed. Several recent developments, including tensile, compressive, and bending tests fresh whole bone specimens, offer the possibility to understand animal bones mechanical behavior. Therefore, the aims of the present study were to determine the effects of three point bending tests on the lamb metacarpal bones at different speeds and determine the mechanical properties of bone and to compare these properties with the finite element analysis of the tests. 12 specimens were obtained from 1 year old Ankara curly lambs. Three point bending tests were conducted using three different compression speeds to assess and compare bone fracture properties. From the test results bending moments, stresses, strains and deformations were calculated for three different compression speeds. Finite Element Analysis results were compared to the test results. Because of the use fresh bone specimens of an animal part are used like in vivo tests in biomechanical studies, investigating failure loads of the metacarpus by bending tests and numerical analysis are guiding for clinical operations and computer simulations.
- Open Access
- 7 September 2016
- Published by IntechOpen
The Reliability of Autonomous Vehicles Under Collisions
The Reliability of Autonomous Vehicles Under Collisions | InTechOpen, Published on: 2016-09-07. Authors: Ibrahim Kutay Yilmazcoban
- 7 September 2016
- Published by IntechOpen
Open AccessThe Reliability of Autonomous Vehicles Under Collisions
The Reliability of Autonomous Vehicles Under Collisions | InTechOpen, Published on: 2016-09-07. Authors: Ibrahim Kutay Yilmazcoban
- 1 July 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 130 (1) , 342-346
Ballistic Protection Evaluation of Sequencing the Composite Material Sandwich Panels for the Reliable Combination of Armor Layers
- 1 July 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 130 (1) , 342-346
Ballistic Protection Evaluation of Sequencing the Composite Material Sandwich Panels for the Reliable Combination of Armor Layers