MÖMehmet Özer

Mehmet Özer

*This is an algorithmically generated author record based on publicly available information.

Mehmet Özer has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Low velocity impact responses of symmetric and asymmetric curved foam core sandwich panels

    by Fatih Balıkoğlu, Tayfur Kerem Demircioğlu, Berkan Hızarcı, Mehmet Özer

    This work aims to experimentally examine the effects of various fibre reinforcements and curvature on the low-speed impact load responses of curved sandwich composites. Plain woven E-glass, S-glass, carbon fibre and twill woven carbon fibre reinforcements with the same areal weight were used as face sheets and PVC foam as core material in the fabrication of sandwich composites. A low-speed impact testing apparatus including a hemispherical impactor was used to conduct low-speed impact tests at various energy levels. Impact energy levels were determined for rebound, penetration, and total perforation of the specimens. Twill woven carbon exhibited superior performance for low-velocity impact damage resistance and tolerance in comparison with plain woven carbon and glass fibres. The absorbed impact energy decreased with the asymmetrical arrangement, and the sandwich specimens with twill-woven face sheets showed the best performance among the symmetrical and asymmetrical panels.


  • HARDOX 450, ALUMİNYUM BALPETEĞİ VE ARAMİD/EPOKSİ TABAKALI HİBRİT ZIRH PLAKALARININ BALİSTİK DAVRANIŞININ İNCELENMESİ

    by Mehmet Özer, Kaan Ferikel, İbRahim Kutay Yılmazçoban, Tayfur Kerem Demircioğlu, Fatih Balikoglu, Can Çivi

    Bu çalışmada, Hardox 450 çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinden oluşan tekli ve çoklu hibrit zırh yapılarının balistik performansı araştırılmıştır. Test levhalarına 833 ± 15 m/s namlu çıkış hızına sahip 7.62 tam metal kaplama mermi ile deneysel balistik testler gerçekleştirilmiştir. Balistik test uygulanacak levhalar 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Test levhaları dört kenarından sabitlenmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Deneysel çalışmalarda, vurma yüzeyine göre sırasıyla 4 mm Hardox 450, 24 kat Aramid /epoksi laminat kompozit ve 10 mm Alüminyum bal peteğinden oluşan hibrit zırh yapısı darbe enerjisine balistik direnç gösterememiştir. Öte yandan tekli yapı olarak kullanılan 6 mm Hardox 450 zırh plakası darbe enerjisine balistik direnç sergilemiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmış; arka yüzey çöküntü miktarı ve sönümlenen enerji miktarları karşılaştırmalı olarak verilmiştir.


  • Open Access

    Armox 500T Zırh Çeliği İçeren Hibrit Zırh Plakalarının 7.62 mm Tam Metal Kaplama Mermi Karşısındaki Balistik Davranışının Deneysel ve Sayısal Olarak Araştırılması

    by Mehmet Özer, Kaan Ferikel, İbRahim Kutay Yılmazçoban, Tayfur Kerem Demircioğlu, Fatih Balikoglu, Can Çivi

    Bu çalışmada, Armox 500T zırh çeliği, Aramid /epoksi laminat kompozit ve Alüminyum bal peteği malzemelerinin tekli ve çoklu hibrit zırh yapıları çeşitli kombinasyonlarla bir araya getirilmiş ve balistik performansları araştırılmıştır. Deneysel çalışma, namlu çıkış hızı 847 ± 10 m/s olan 7.62×51 mm tam metal kaplama mermi ile balistik testler gerçekleştirilmiştir. Balistik darbe levhanın vurma yüzeyine dik gelecek şekilde atış yapılarak gerçekleştirilmiştir. Balistik test levhaları 250×250 mm boyutlarına sahip olup kalınlıkları ise malzeme konfigürasyonuna göre farklılık göstermiştir. Sonlu elemanlar analizi LS-Dyna programında açık zaman entegrasyonu yöntemi ile yapılmıştır. Deneysel çalışmalarda, monolitik çelik ve hibrit oluşan zırh yapısı balistik koruma sağlamamıştır. Bununla birlikte, metal ve kompozit levhaların hibritleşmesi ile sönümlenen balistik darbe enerji miktarı artırmıştır. Ayrıca, çalışmaya dahil edilen tüm zırh kombinasyonları ağırlık ve kalınlık açısından değerlendirilmiş birbirlerine üstünlükleri belirlenmeye çalışılmıştır. Hibritleşme ile elde edilen enerji sönümleme değerleri, plakaların ağırlığındaki artışa göre daha büyük bir yüzdesel artış sergilemiştir. Zırh kombinasyonlarının sonlu elemanlar analizi neticeleri deneysel veriler ile karşılaştırılması sağlanmış ve iyi uyum gözlemlenmiştir.


  • Experimental study on resin pin-reinforced marine sandwich composites under quasi-static indentation load

    by Fatih Balikoğlu, Tayfur Kerem Demi̇rci̇oğlu, Mehmet Özer, Ali Işiktaş

    This study aims to experimentally examine the indentation behaviour of marine sandwich composites with pin-reinforced polyvinyl chloride foam core and E-glass face sheets. The effects of indenter diameter, resin pin diameter, and arrangement on force-displacement, maximum contact force, and absorbed energy values of sandwich panels were evaluated by the indentation tests. Throughout the experiments, the contact forces increased as the pin diameter increased. The contact forces reduced as the distance between pin diameters increased. Additionally, the values of absorbed energy increased as the diameters of the resin pin and indenter increased. Placing the pins more closely together additionally allows the material to absorb more energy in the event of indentation. A visual inspection took place on the post-indentation cross-sections of the sandwich specimens to detect any damage modes. Damage modes varied depending on the size of the indenter and the hole pattern in the foam core.

  • Open Access

    Boriding Effect on the Hardness of AISI 1020, AISI 1060, AISI 4140 Steels and Application of Artificial Neural Network for Prediction of Borided Layer

    by Mehmet Özer, Fatih Balikoglu, Tayfur Kerem Demircioğlu, Yunus Emre Nehri

    Artificial neural network approach was used to predict the thicknesses of total (FeB+Fe2B), FeB and Fe2B borides layers of AISI 1020, AISI 1060, and AISI 4140 steels. Boronizing heat treatment was conducted in a solid medium comprising of EKabor®2 powders at 840–960 ˚C at 40 ˚C intervals for 2, 4, 6, and 8 hours. Optical microscope analysis of the borided layer revealed the saw-tooth (columnar) and planar morphology. The depth of the total (FeB+Fe2B), FeB and Fe2B boride layers was accurately predicted. For total boride layers generated by the artificial neural network model, the average error varied between 0.04 and 7.64 µm. Micro hardness values increased by 423% in AISI 1020, 336% in AISI 1060, and 411% in AISI 41040 after the boronizing process.