Hamed Samadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hamed Samadi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
T. W. Coyle
University of Toronto
3 shared publications- Ali Nemati
Department of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran
1 shared publication Ali Shafyei
Isfahan University of Technology
1 shared publicationE. Garcia
Centre for Advanced Coating Technologies, University of Toronto
1 shared publication- Hamidreza Salimijazi
Isfahan University of Technology
1 shared publication Javad Mostaghimi
University of Toronto
1 shared publication
Latest Publications
- 25 May 2016
- Published by Springer Nature in JOM
- Vol. 68 (10) , 2569-2573
Effect of Samarium Oxide on the Electrical Conductivity of Plasma-Sprayed SOFC Anodes
- 25 May 2016
- Published by Springer Nature in JOM
- Vol. 68 (10) , 2569-2573
Effect of Samarium Oxide on the Electrical Conductivity of Plasma-Sprayed SOFC Anodes
- 23 March 2012
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 21 (5) , 825-830
Plasma Sprayed Coating Using Mullite and Mixed Alumina/Silica Powders
- 23 March 2012
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 21 (5) , 825-830
Plasma Sprayed Coating Using Mullite and Mixed Alumina/Silica Powders
- 15 July 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (20) , 3300-3306
Effect of in-flight particle properties on deposition of air plasma sprayed forsterite
- 15 July 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (20) , 3300-3306
Effect of in-flight particle properties on deposition of air plasma sprayed forsterite
- 24 September 2009
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 18 (5-6) , 996-1003
Modeling the Build-Up of Internal Stresses in Multilayer Thick Thermal Barrier Coatings
- 24 September 2009
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 18 (5-6) , 996-1003
Modeling the Build-Up of Internal Stresses in Multilayer Thick Thermal Barrier Coatings
- 1 January 2006
- Published by Wiley
- p. 29-35
Design of Alternative Multilayer Thick Thermal Barrier Coatings
- 1 January 2006
- Published by Wiley
- p. 29-35
Design of Alternative Multilayer Thick Thermal Barrier Coatings
- 11 April 2005
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Development of Alternative Thermal Barrier Coatings for Diesel Engines
The use of thermal barrier coatings (TBCs) to increase the combustion temperature in diesel engines has been pursued for over 20 years. Increased combustion temperature can increase the efficiency of the engine, decrease the CO and (possibly) the NOx emission rate. However, TBCs have not yet met with wide success in diesel engine applications. The most common TBC system is Yttria Partially Stabilized Zirconia (Y-PSZ) which has shown good performance in turbine blade coatings where temperatures approach 1100°C. To reach the desirable temperature of 850-900°C in the combustion chamber from the current temperature of 350-400°C, a coating with a thickness of order 1mm is required, significantly thicker than turbine blade coatings which are on the order of 100μm thick. This results in different temperature and stress profiles in the coating during service than in the case of turbine coatings, and different failure mechanisms. Recent advances in the control of coating structure have led to the development of new PSZ coating microstructures containing grains and pores with sizes in the range of 100-300 nm. Thermal-mechanical properties of such coatings have been characterized and compared with coatings exhibiting the traditional thermal spray structure to asses their suitability as thick TBC for diesel engine applications. Selected coatings have been subjected to engine testing in an instrumented single cylinder diesel test rig. Among possible alternative materials, one of the most promising is mullite. Mullite has excellent thermo-mechanical behavior; however its low coefficient of thermal expansion creates a large mismatch with the substrate. To address this problem, multilayer systems have been developed which minimize the thermal expansion mismatch stresses while maintaining chemical and phase stability. The design considerations for such multilayer systems are discussed.
- 11 April 2005
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Development of Alternative Thermal Barrier Coatings for Diesel Engines
The use of thermal barrier coatings (TBCs) to increase the combustion temperature in diesel engines has been pursued for over 20 years. Increased combustion temperature can increase the efficiency of the engine, decrease the CO and (possibly) the NOx emission rate. However, TBCs have not yet met with wide success in diesel engine applications. The most common TBC system is Yttria Partially Stabilized Zirconia (Y-PSZ) which has shown good performance in turbine blade coatings where temperatures approach 1100°C. To reach the desirable temperature of 850-900°C in the combustion chamber from the current temperature of 350-400°C, a coating with a thickness of order 1mm is required, significantly thicker than turbine blade coatings which are on the order of 100μm thick. This results in different temperature and stress profiles in the coating during service than in the case of turbine coatings, and different failure mechanisms. Recent advances in the control of coating structure have led to the development of new PSZ coating microstructures containing grains and pores with sizes in the range of 100-300 nm. Thermal-mechanical properties of such coatings have been characterized and compared with coatings exhibiting the traditional thermal spray structure to asses their suitability as thick TBC for diesel engine applications. Selected coatings have been subjected to engine testing in an instrumented single cylinder diesel test rig. Among possible alternative materials, one of the most promising is mullite. Mullite has excellent thermo-mechanical behavior; however its low coefficient of thermal expansion creates a large mismatch with the substrate. To address this problem, multilayer systems have been developed which minimize the thermal expansion mismatch stresses while maintaining chemical and phase stability. The design considerations for such multilayer systems are discussed.