WSWalaa Mahmoud Shehata

Walaa Mahmoud Shehata

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Walaa Mahmoud Shehata has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A comparative study of mono ethylene glycol economic production via different techniques

    by Walaa M. Shehata, Taha G. Nady, Fatma K. Gad, Abeer M. Shoaib, Ahmed A. Bhran

    Mono-ethylene glycol (MEG) is a high-volume chemical intermediate used as a raw material for a variety of chemical products. It could also be used as a hydrate inhibitor in natural gas. Recently, the importance of MEG has been increased due to its usage as a supporting emulsifier in diesel engines to reduce NOx and soot emissions, in addition to its usage as an additive to dual fuel diesel engines. The increase consumption of MEG in wide range of applications leads to the search for the most efficient, environmental friendly and cost effective technique to produce more quantities of it. MEG is most commonly manufactured via the hydration of ethylene oxide (EO). In this work, two different technologies of EO hydration to produce MEG are compared; the direct hydration of EO with water and the indirect hydration through the usage of ethylene carbonate (EC) as an intermediate. Comparative economic and environmental impact assessments were performed based on plant-scale simulations (per 600,000 tons per year of MEG produced) of the two hydration technologies using Aspen HYSYS version 11 simulation software. Economic analysis showed that the utilities’ energy consumption for direct hydration process is significantly higher than for indirect hydration by 279 megawatts. On the other hand, the environmental impact assessments showed that GHG emissions from natural gas power generation from utilities from direct hydration are three times greater than GHG emissions from indirect hydration. This leads to indirect hydration of ethylene oxide through ethylene carbonate formation being considered economically and environmentally preferable compared to the direct hydration process of ethylene oxide.


  • Open Access

    Optimum Planning of Carbon Capture and Storage Network Using Goal Programming

    by Fatma M. Ayyad, Walaa M. Shehata, Ahmed A. Bhran, Abdelrahman G. Gadallah, Abeer M. Shoaib

    Carbon capture and storage (CCS) is a critical technology used for mitigating climate change by capturing carbon dioxide emissions from industrial sources and storing them underground to prevent their release into the atmosphere. Despite its potential, optimizing CCS systems for cost-effectiveness and efficiency improvement remains a significant challenge. In this paper, the optimization of CCS systems through the development and application of two mathematical optimization techniques is introduced. The first technique is based on using a superstructure optimization model, while the second technique relies on applying a goal programming optimization model. These models were solved using LINGO software version API 14.0.5099.166 to enhance the efficiency and cost-effectiveness of CCS systems. The first model, seeking to maximize the exchange of CO2 flowrate from sources to sinks, achieved a CO2 capture rate of 93.36% with an annual total cost of USD 1.175 billion. The second model introduced a novel mixed-integer non-linear programming (MINLP) approach for multi-objective optimization, targeting the minimization of total system cost, alternative storage, and unutilized storage while maximizing CO2 load exchange. The application of the second model, when prioritized to maximize CO2 flowrate exchange using the goal programming technique, resulted in a cost reduction of 36.46% and a CO2 capture rate of 75.87%. In contrast, when the second model prioritized minimizing the total annual cost, a 48% cost reduction was achieved, and the CO2 capture rate was decreased by 68.37%. A comparison of the two models’ results is presented. The results showed that the second model, with the priority of maximizing CO2 capture, provides the best economic–environmental objective balance, which offers notable cost reductions while keeping an efficient CO2 capture rate. This study highlights the potential of advanced mathematical modeling in increasing the feasibility of CCS as one of the very important strategies of mitigating climate change and reducing global warming.


  • A multi-objective optimization approach for integrating isomerization hydroprocessing unit with hydrogen network

    by Walaa Mahmoud Shehata

    The isomerization unit improves the light naphtha research octane number with better environmental impacts. Recent developments in increasing the octane number in the isomerization unit are leading to increased demand for refinery hydrogen. However, the disconnected hydrogen network and increasing the octane number in isomerization unit has led to a shortfall of hydrogen to meet the hydrogen demand. The present work is an integrated approach to the isomerization process in refineries and hydrogen network design. Modeling and optimization of the overall hydrogen network objective to minimize the total consumption of fresh hydrogen and maximize the isomerization octane number using a goal programming multi-objective optimization approach is presented. The model is introduced for two cases, reuse/recycling and hydrogen regeneration networks. The global network model is a multi-objective nonlinear programming model, and is optimized using Lingo optimization software version 14. The results showed that by integrating the isomerization model with the hydrogen reuse/recycling network, the fresh hydrogen saving was 20.871 kmol/h compared to 7.772 kmol/h in the case of neglecting the isomerization model. On the other hand, a significant reduction of 447.898 kmol/h in fresh hydrogen was achieved in the hydrogen regeneration network when including the isomerization model compared to that achieved when neglecting the isomerization model (343.261 kmol/h). In addition, the optimum operating conditions, feed specifications and hydrogen consumption of the isomerization unit that gives the maximum research octane number and the minimum fresh hydrogen were determined for both the reuse/recycling and hydrogen regeneration network cases.

  • Open Access

    Energy saving in oilfields by using waste heat in the disposed water

    by Walaa Mahmoud Shehata, Mohamed Galal Helal, Fatma Khalifa Gad

    The present work aims to retrofit an existing Egyptian oilfield plant to improve desalter performance and reduce the power of crude oil shipping pumps. In this work waste heat in disposed water that represents a value is used in heating brackish water injected over desalter and in heating crude oil before shipping. ASPEN HYSYS version 11 simulation software was used. The retrofit of the considered oilfield plant is based on the implementation of two new heat exchangers to recover waste heat in the disposed water. The results showed that the use of waste heat in heating the brackish water in the desalter from 30 to 71.11ºC will increase the operating temperature of the desalter and thus increase the sedimentation and separation rate. On the other hand, using waste heat in heating the crude oil before shipping from 37.78 to 71.11ºC reduces the oil viscosity from 1.536 to 0.9735 cSt. Reducing the viscosity of the crude oil will reduce the pressure drop of the shipping pumps, and therefore the power required to pump the oil will be reduced. The presented retrofit design can be used as a guide in upgrading existing plants and plants under the design phase.

  • A superstructure model for indirect inter-plant water integration for selecting the optimum single-pass and partitioning regenerators

    by Walaa Shehata, Fatma Gad

    Water scarcity and stricter regulations on industrial effluents have led to a different view of water use. Water recycling / reuse is the most common technology used to reduce water and wastewater. The integration of multiple industrial plants, known as the inter-plant integration, has gained a great attention in recent years. Inter- plant water integration is a new technology that can be applied to water integration. This technology can be used to reduce water consumption and water discharge of various water networks in eco-industrial plants. This can be achieved directly or indirectly through the use of regenerators. In this work, a superstructure model for the indirect inter-plant water integration is proposed, for selecting the optimum regenerators of single pass and partitioning regenerators. Mixed integer non-linear program (MINLP) was formulated and solved for optimum solution. A literature case study is used to verify the effectiveness of the proposed model. The results showed that there was a significant decrease in the fresh and the discharge water of the integrated plants.


  • Open Access

    Improving gasoline quality produced from MIDOR light naphtha isomerization unit

    by M.F. Mohamed, W.M. Shehata, A.A. Abdel Halim, F.K. Gad