Dinis Reis Oliveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dinis Reis Oliveira has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Lena Granhag
A Department of Mechanics and Maritime Sciences , Chalmers University of Technology , Gothenburg , Sweden
4 shared publications Lars Larsson
2 shared publications- Tiago Sotto Mayor
Transport Phenomena Research Center (CEFT), Associate Laboratory in Chemical Engineering (ALiCE) Faculty of Engineering, University of Porto Rua Dr. Roberto Frias, 4200-465 Porto, Portugal
2 shared publications - Ann I. Larsson
University of Gothenburg, Department of Marine Sciences, Tjärnö Marine Laboratory, Strömstad SE 452 96, Sweden
1 shared publication - Irma Yeginbayeva
Department of R&D (Research and Development), Jotun A/S, Sandefjord, Vestfold, Norway
1 shared publication Jennie Andersson
1 shared publication
Latest Publications
- Open Access
- 1 June 2020
- Published by Elsevier in Applied Ocean Research
- Vol. 99
Review and comparison of methods to model ship hull roughness
- 1 June 2020
- Published by Elsevier in Applied Ocean Research
- Vol. 99
Open AccessReview and comparison of methods to model ship hull roughness
- 1 June 2020
- Published by Elsevier in Ocean Engineering
- Vol. 205
A novel indicator for ship hull and propeller performance: Examples from two shipping segments
- 1 June 2020
- Published by Elsevier in Ocean Engineering
- Vol. 205
A novel indicator for ship hull and propeller performance: Examples from two shipping segments
- Open Access
- 15 March 2020
- Published by Taylor & Francis in Biofouling
- Vol. 36 (3) , 332-350
Ship hull in-water cleaning and its effects on fouling-control coatings
Today, ship hull fouling is managed through fouling-control coatings, complemented with in-water cleaning. During cleaning, coating damage and wear must be avoided, for maximum coating lifetime and reduced antifoulant release. When possible, cleaning should target early stages of fouling, using minimal forces. However, such forces, and their effects on coatings, have not yet been fully quantified. In this one-year study, minimal cleaning forces were determined using a newly-designed immersed waterjet. The results show that bi-monthly/monthly cleaning, with maximum wall shear stress up to ∼1.3 kPa and jet stagnation pressure ∼0.17 MPa, did not appear to cause damage or wear on either the biocidal antifouling (AF) or the biocide-free foul-release (FR) coatings. The AF coating required bi-monthly cleanings to keep fouling to incipient slime (time-averaged results), while the FR coating had a similar fouling level even without cleaning. The reported forces may be used in matching cleaning parameters to the adhesion strength of the early stages of fouling.
- 15 March 2020
- Published by Taylor & Francis in Biofouling
- Vol. 36 (3) , 332-350
Open AccessShip hull in-water cleaning and its effects on fouling-control coatings
Today, ship hull fouling is managed through fouling-control coatings, complemented with in-water cleaning. During cleaning, coating damage and wear must be avoided, for maximum coating lifetime and reduced antifoulant release. When possible, cleaning should target early stages of fouling, using minimal forces. However, such forces, and their effects on coatings, have not yet been fully quantified. In this one-year study, minimal cleaning forces were determined using a newly-designed immersed waterjet. The results show that bi-monthly/monthly cleaning, with maximum wall shear stress up to ∼1.3 kPa and jet stagnation pressure ∼0.17 MPa, did not appear to cause damage or wear on either the biocidal antifouling (AF) or the biocide-free foul-release (FR) coatings. The AF coating required bi-monthly cleanings to keep fouling to incipient slime (time-averaged results), while the FR coating had a similar fouling level even without cleaning. The reported forces may be used in matching cleaning parameters to the adhesion strength of the early stages of fouling.
- Open Access
- 7 February 2019
- Published by Taylor & Francis in Biofouling
- Vol. 35 (2) , 244-258
Towards an absolute scale for adhesion strength of ship hull microfouling
In-water ships’ hull cleaning enables significant fuel savings through removal of marine fouling from surfaces. However, cleaning may also shorten the lifetime of hull coatings, with a subsequent increase in the colonization and growth rate of fouling organisms. Deleterious effects of cleaning would be minimized by matching cleaning forces to the adhesion strength of the early stages of fouling, or microfouling. Calibrated waterjets are routinely used to compare different coatings in terms of the adhesion strength of microfouling. However, an absolute scale is lacking for translating such results into cleaning forces, which are of interest for the design and operation of hull cleaning devices. This paper discusses how such forces can be determined using computational fluid dynamics. Semi-empirical formulae are derived for forces under immersed waterjets, where the normal and tangential components of wall forces are given as functions of different flow parameters. Nozzle translation speed is identified as a parameter for future research, as this may affect cleaning efficacy.
- 7 February 2019
- Published by Taylor & Francis in Biofouling
- Vol. 35 (2) , 244-258
Open AccessTowards an absolute scale for adhesion strength of ship hull microfouling
In-water ships’ hull cleaning enables significant fuel savings through removal of marine fouling from surfaces. However, cleaning may also shorten the lifetime of hull coatings, with a subsequent increase in the colonization and growth rate of fouling organisms. Deleterious effects of cleaning would be minimized by matching cleaning forces to the adhesion strength of the early stages of fouling, or microfouling. Calibrated waterjets are routinely used to compare different coatings in terms of the adhesion strength of microfouling. However, an absolute scale is lacking for translating such results into cleaning forces, which are of interest for the design and operation of hull cleaning devices. This paper discusses how such forces can be determined using computational fluid dynamics. Semi-empirical formulae are derived for forces under immersed waterjets, where the normal and tangential components of wall forces are given as functions of different flow parameters. Nozzle translation speed is identified as a parameter for future research, as this may affect cleaning efficacy.
- Open Access
- 19 February 2018
- Published by Taylor & Francis in Biofouling
- Vol. 34 (3) , 262-272
Effect of ship hull form on the resistance penalty from biofouling
Hull biofouling is a well-known problem for the shipping industry, leading to increased resistance and fuel consumption. Considering that the effects of hull form on resistance are known to be higher for a less slender hull, it is hypothesised in this paper that the effect of biofouling roughness on resistance is also dependent on the hull form. To test this hypothesis, previously reported full-scale numerical results on a containership are re-analysed. Form effects on roughness penalties, corresponding to KΔCT = 0.058 ± 0.025, are observed at a low speed (19 knots, Res = 2.29 × 109), which are however cancelled out by traditionally neglected roughness effects on wave-making resistance at a higher speed (24 knots, Res = 2.89 × 109). It is concluded that hull form effects on biofouling penalties can be significant at low speeds, though not generalisable for higher speeds, namely when wave-making resistance corresponds to ≥ 29% of total resistance.
- 19 February 2018
- Published by Taylor & Francis in Biofouling
- Vol. 34 (3) , 262-272
Open AccessEffect of ship hull form on the resistance penalty from biofouling
Hull biofouling is a well-known problem for the shipping industry, leading to increased resistance and fuel consumption. Considering that the effects of hull form on resistance are known to be higher for a less slender hull, it is hypothesised in this paper that the effect of biofouling roughness on resistance is also dependent on the hull form. To test this hypothesis, previously reported full-scale numerical results on a containership are re-analysed. Form effects on roughness penalties, corresponding to KΔCT = 0.058 ± 0.025, are observed at a low speed (19 knots, Res = 2.29 × 109), which are however cancelled out by traditionally neglected roughness effects on wave-making resistance at a higher speed (24 knots, Res = 2.89 × 109). It is concluded that hull form effects on biofouling penalties can be significant at low speeds, though not generalisable for higher speeds, namely when wave-making resistance corresponds to ≥ 29% of total resistance.
- 1 February 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 117, 71-79
Numerical analysis of the flow and heat transfer in cylindrical clothing microclimates – Influence of the microclimate thickness ratio
- 1 February 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 117, 71-79
Numerical analysis of the flow and heat transfer in cylindrical clothing microclimates – Influence of the microclimate thickness ratio
- Open Access
- 17 October 2016
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 4 (4) , 66
Matching Forces Applied in Underwater Hull Cleaning with Adhesion Strength of Marine Organisms
Biofouling is detrimental to the hydrodynamic performance of ships. In spite of advances in hull coating technology, a ship must usually undergo underwater hull cleaning to remove biofouling during her in-service time. However, some cleaning practices may also lead to decreased lifetime of the fouling-control coating. Therefore, cleaning forces should be minimized, according to the adhesion strength of marine organisms present on the hull. In this article, values of adhesion strength found in available literature are discussed in the light of current knowledge on hull cleaning technology. Finally, the following knowledge gaps are identified: (1) data on adhesion strength of naturally-occurring biofouling communities are practically absent; (2) shear forces imparted by current cleaning devices on low-form fouling (microfouling) and corresponding effects on hull coatings are largely unknown. This knowledge would be valuable for both developers and users of cleaning technology.
- 17 October 2016
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 4 (4) , 66
Open AccessMatching Forces Applied in Underwater Hull Cleaning with Adhesion Strength of Marine Organisms
Biofouling is detrimental to the hydrodynamic performance of ships. In spite of advances in hull coating technology, a ship must usually undergo underwater hull cleaning to remove biofouling during her in-service time. However, some cleaning practices may also lead to decreased lifetime of the fouling-control coating. Therefore, cleaning forces should be minimized, according to the adhesion strength of marine organisms present on the hull. In this article, values of adhesion strength found in available literature are discussed in the light of current knowledge on hull cleaning technology. Finally, the following knowledge gaps are identified: (1) data on adhesion strength of naturally-occurring biofouling communities are practically absent; (2) shear forces imparted by current cleaning devices on low-form fouling (microfouling) and corresponding effects on hull coatings are largely unknown. This knowledge would be valuable for both developers and users of cleaning technology.
- Open Access
- 14 September 2015
- Published by Springer Nature in Extreme Physiology & Medicine
- Vol. 4 (S1) , 1-A68
Numerical simulation of the transport phenomena in tilted clothing microclimates
- 14 September 2015
- Published by Springer Nature in Extreme Physiology & Medicine
- Vol. 4 (S1) , 1-A68
Open AccessNumerical simulation of the transport phenomena in tilted clothing microclimates