Freddy Forero
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Freddy Forero has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Victor Champac
National Institute for Astrophysics, Optics and Electronics (INAOE), Puebla, Mexico
5 shared publications - Michel Renovell
University of Montpellier/CNRS
3 shared publications - Andres Gomez
National Institute for Astrophysics, Optics and Electronics
1 shared publication - Florence Azaïs
LIRMM, CNRS, Universit de Montpellier, Montpellier, France
1 shared publication - Gustavo Aguirre
National Institute for Astrophysics, Optics and Electronics (INAOE), Puebla, Mexico
1 shared publication - Hector Villacorta
Engineering Department, Panamerica University, Aguascalientes 20290, Mexico
1 shared publication
Latest Publications
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (3) , 841-852
Cost-Effective Analytical Models of Resistive Opens Defects in FinFET Technology
FinFET technology has become an attractive candidate for high-performance and power-efficient applications. However, its susceptibility to defects increases due to the complexity of the process fabrications and smaller feature sizes. This article proposes compact and low-cost analytical models to evaluate the delay increase in FinFET-based circuits due to resistive open defects. The models rely on electrical simulations to precharacterize the circuit library. Analytical expressions are developed for the three types of resistive opens that may occur in FinFET-based logic cells using multifin and multifinger structures. These types of resistive opens include: a resistive open at the drain or source of the transistors (RODS), a resistive open affecting the gate of a single transistor, and a resistive open affecting the gates of both nMOS and pMOS transistors. Compact analytical models are also developed to evaluate the delay increase due to the resistive open defects under process variations. Independent and correlated process variations are taken into account. The analytical models have been validated against SPICE electrical simulations. The proposed analytical models can be used to evaluate the detectability of resistive open defects, significantly reducing the cost of dealing with different defect sizes. Potential applications of the developed analytical models are delineated. This work allows us to have higher quality and reliable electronic products.
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (3) , 841-852
Cost-Effective Analytical Models of Resistive Opens Defects in FinFET Technology
FinFET technology has become an attractive candidate for high-performance and power-efficient applications. However, its susceptibility to defects increases due to the complexity of the process fabrications and smaller feature sizes. This article proposes compact and low-cost analytical models to evaluate the delay increase in FinFET-based circuits due to resistive open defects. The models rely on electrical simulations to precharacterize the circuit library. Analytical expressions are developed for the three types of resistive opens that may occur in FinFET-based logic cells using multifin and multifinger structures. These types of resistive opens include: a resistive open at the drain or source of the transistors (RODS), a resistive open affecting the gate of a single transistor, and a resistive open affecting the gates of both nMOS and pMOS transistors. Compact analytical models are also developed to evaluate the delay increase due to the resistive open defects under process variations. Independent and correlated process variations are taken into account. The analytical models have been validated against SPICE electrical simulations. The proposed analytical models can be used to evaluate the detectability of resistive open defects, significantly reducing the cost of dealing with different defect sizes. Potential applications of the developed analytical models are delineated. This work allows us to have higher quality and reliable electronic products.
- Open Access
- 9 December 2022
- Published by Association for Computing Machinery (ACM) in ACM Journal on Emerging Technologies in Computing Systems
- Vol. 19 (1) , 1-19
B-open Defect: A Novel Defect Model in FinFET Technology
This article proposes an electrical analysis of a new defect mechanism, to be named as b-open defect, which may occur in nanometer technologies due to the use of the Self-Aligned Double Patterning (SADP) technique. In metal lines making use of the SADP technique, a single dust particle may cause the simultaneous occurrence of a bridge defect and an open defect. When the two defects impact the same gates, the electrical effects of the bridge and the open combine and exhibit a new specific electrical behavior; we call this new defect behavior a b-open. As a consequence, existing test generation methodologies may miss defect detection. The electrical behavior of the b-open defect is first analyzed graphically and then validated through extensive SPICE simulations. The test pattern conditions to detect the b-open defect are finally determined, and it is shown that the b-open defect requires specific test generation.
- 9 December 2022
- Published by Association for Computing Machinery (ACM) in ACM Journal on Emerging Technologies in Computing Systems
- Vol. 19 (1) , 1-19
Open AccessB-open Defect: A Novel Defect Model in FinFET Technology
This article proposes an electrical analysis of a new defect mechanism, to be named as b-open defect, which may occur in nanometer technologies due to the use of the Self-Aligned Double Patterning (SADP) technique. In metal lines making use of the SADP technique, a single dust particle may cause the simultaneous occurrence of a bridge defect and an open defect. When the two defects impact the same gates, the electrical effects of the bridge and the open combine and exhibit a new specific electrical behavior; we call this new defect behavior a b-open. As a consequence, existing test generation methodologies may miss defect detection. The electrical behavior of the b-open defect is first analyzed graphically and then validated through extensive SPICE simulations. The test pattern conditions to detect the b-open defect are finally determined, and it is shown that the b-open defect requires specific test generation.
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (9) , 2180-2190
Modeling and Detectability of Full Open Gate Defects in FinFET Technology
FinFET technology is an attractive candidate for high-performance and power-efficient application and is currently used for several electronic products. FinFET technology incorporates new technologies in the manufacturing processes that may generate new defect topologies which need to be considered during test generation. This paper analyzes the electrical behavior of full open gate defects, i.e., a transistor gate with infinite resistance. It is shown that classical models, called single open (SO) and interconnect open (IO), that have been proposed in the past for CMOS technology are not sufficient in FinFET technology. The modern FinFET-based logic cells using multifin and multifinger design techniques give rise to new specific defect topologies called ``subset full open gate defect.'' The static and dynamic electrical behaviors of the two new topologies, subset SO (SOsub) and subset IO ( IOsub), are analyzed, and the detectability of the defect in the context of Boolean testing and delay testing is derived. The detectability is analyzed taking into account process variation, temperature, and power supply control.
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (9) , 2180-2190
Modeling and Detectability of Full Open Gate Defects in FinFET Technology
FinFET technology is an attractive candidate for high-performance and power-efficient application and is currently used for several electronic products. FinFET technology incorporates new technologies in the manufacturing processes that may generate new defect topologies which need to be considered during test generation. This paper analyzes the electrical behavior of full open gate defects, i.e., a transistor gate with infinite resistance. It is shown that classical models, called single open (SO) and interconnect open (IO), that have been proposed in the past for CMOS technology are not sufficient in FinFET technology. The modern FinFET-based logic cells using multifin and multifinger design techniques give rise to new specific defect topologies called ``subset full open gate defect.'' The static and dynamic electrical behaviors of the two new topologies, subset SO (SOsub) and subset IO ( IOsub), are analyzed, and the detectability of the defect in the context of Boolean testing and delay testing is derived. The detectability is analyzed taking into account process variation, temperature, and power supply control.
- 26 June 2019
- Published by Springer Nature
- p. 207-231
Analysis of Bridge Defects in STT-MRAM Cells Under Process Variations and a Robust DFT Technique for Their Detection
- 26 June 2019
- Published by Springer Nature
- p. 207-231
Analysis of Bridge Defects in STT-MRAM Cells Under Process Variations and a Robust DFT Technique for Their Detection
- 23 February 2018
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 34 (2) , 123-134
Detectability Challenges of Bridge Defects in FinFET Based Logic Cells
- 23 February 2018
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 34 (2) , 123-134
Detectability Challenges of Bridge Defects in FinFET Based Logic Cells