Michel Renovell
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michel Renovell has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
F. Azais
4 shared publications- Freddy Forero
National Institute of Astrophysics, Optics and Electronics (INAOE), Puebla, Mexico
3 shared publications - Serge Bernard
CNRS, LIRMM, Université de Montpellier, Montpellier, France
3 shared publications - Victor Champac
National Institute for Astrophysics, Optics and Electronics (INAOE), Puebla, Mexico
3 shared publications - Vincent Kerzérho
LIRMM, Université de Montpellier, CNRS 4 , 34095 Montpellier
3 shared publications - Yves Bertrand
Institute of Pediatric Hematology and Oncology, Hospices Civils de Lyon, Claude Bernard Lyon I University, Lyon, France
3 shared publications
Latest Publications
- Open Access
Multilinear Regression Analysis between Local Bioimpedance Spectroscopy and Fish Morphological Parameters
Repeated fish handling may cause stress, which biases experiments and so affects the results. In order to reduce this, the present study investigates the benefit of using bioimpedance analysis to estimate morphological parameters. Bioimpedance analysis is a non-lethal and integrative electrical measurement that can be used to estimate several kinds of physiological parameters and is used in medicine and ecological studies. In particular, bioimpedance can monitor the individual growth of fish, which is a prerequisite for most biological and ecological studies, as body size is one of the best predictors for numerous life history traits and ecological parameters. After a short review on the use of bioimpedance measurement in medicine and ecology, we illustrate the potential of bioimpedance spectroscopy, as opposed to single frequency measurement, for experimental studies on fish. Using a monolithic four-contact electrode and a cost-effective portable system, we conducted bioimpedance spectroscopy on 159 sardines. The association between the length, weight, and electrical parameters obtained at different frequencies from the bioimpedance spectroscopy was investigated. Our results show that accounting for more than one frequency substantially improves the prediction of length and weight. We conclude that bioimpedance could potentially be a powerful tool for monitoring fish growth in ecological studies.
Open AccessMultilinear Regression Analysis between Local Bioimpedance Spectroscopy and Fish Morphological Parameters
Repeated fish handling may cause stress, which biases experiments and so affects the results. In order to reduce this, the present study investigates the benefit of using bioimpedance analysis to estimate morphological parameters. Bioimpedance analysis is a non-lethal and integrative electrical measurement that can be used to estimate several kinds of physiological parameters and is used in medicine and ecological studies. In particular, bioimpedance can monitor the individual growth of fish, which is a prerequisite for most biological and ecological studies, as body size is one of the best predictors for numerous life history traits and ecological parameters. After a short review on the use of bioimpedance measurement in medicine and ecology, we illustrate the potential of bioimpedance spectroscopy, as opposed to single frequency measurement, for experimental studies on fish. Using a monolithic four-contact electrode and a cost-effective portable system, we conducted bioimpedance spectroscopy on 159 sardines. The association between the length, weight, and electrical parameters obtained at different frequencies from the bioimpedance spectroscopy was investigated. Our results show that accounting for more than one frequency substantially improves the prediction of length and weight. We conclude that bioimpedance could potentially be a powerful tool for monitoring fish growth in ecological studies.
- Open Access
- 9 December 2022
- Published by Association for Computing Machinery (ACM) in ACM Journal on Emerging Technologies in Computing Systems
- Vol. 19 (1) , 1-19
B-open Defect: A Novel Defect Model in FinFET Technology
This article proposes an electrical analysis of a new defect mechanism, to be named as b-open defect, which may occur in nanometer technologies due to the use of the Self-Aligned Double Patterning (SADP) technique. In metal lines making use of the SADP technique, a single dust particle may cause the simultaneous occurrence of a bridge defect and an open defect. When the two defects impact the same gates, the electrical effects of the bridge and the open combine and exhibit a new specific electrical behavior; we call this new defect behavior a b-open. As a consequence, existing test generation methodologies may miss defect detection. The electrical behavior of the b-open defect is first analyzed graphically and then validated through extensive SPICE simulations. The test pattern conditions to detect the b-open defect are finally determined, and it is shown that the b-open defect requires specific test generation.
- 9 December 2022
- Published by Association for Computing Machinery (ACM) in ACM Journal on Emerging Technologies in Computing Systems
- Vol. 19 (1) , 1-19
Open AccessB-open Defect: A Novel Defect Model in FinFET Technology
This article proposes an electrical analysis of a new defect mechanism, to be named as b-open defect, which may occur in nanometer technologies due to the use of the Self-Aligned Double Patterning (SADP) technique. In metal lines making use of the SADP technique, a single dust particle may cause the simultaneous occurrence of a bridge defect and an open defect. When the two defects impact the same gates, the electrical effects of the bridge and the open combine and exhibit a new specific electrical behavior; we call this new defect behavior a b-open. As a consequence, existing test generation methodologies may miss defect detection. The electrical behavior of the b-open defect is first analyzed graphically and then validated through extensive SPICE simulations. The test pattern conditions to detect the b-open defect are finally determined, and it is shown that the b-open defect requires specific test generation.
- 1 January 2022
- Published by Elsevier in Aquaculture
- Vol. 547
Study differentiating fish oocyte developmental stages using bioimpedance spectroscopy
- 1 January 2022
- Published by Elsevier in Aquaculture
- Vol. 547
Study differentiating fish oocyte developmental stages using bioimpedance spectroscopy
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (9) , 2180-2190
Modeling and Detectability of Full Open Gate Defects in FinFET Technology
FinFET technology is an attractive candidate for high-performance and power-efficient application and is currently used for several electronic products. FinFET technology incorporates new technologies in the manufacturing processes that may generate new defect topologies which need to be considered during test generation. This paper analyzes the electrical behavior of full open gate defects, i.e., a transistor gate with infinite resistance. It is shown that classical models, called single open (SO) and interconnect open (IO), that have been proposed in the past for CMOS technology are not sufficient in FinFET technology. The modern FinFET-based logic cells using multifin and multifinger design techniques give rise to new specific defect topologies called ``subset full open gate defect.'' The static and dynamic electrical behaviors of the two new topologies, subset SO (SOsub) and subset IO ( IOsub), are analyzed, and the detectability of the defect in the context of Boolean testing and delay testing is derived. The detectability is analyzed taking into account process variation, temperature, and power supply control.
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (9) , 2180-2190
Modeling and Detectability of Full Open Gate Defects in FinFET Technology
FinFET technology is an attractive candidate for high-performance and power-efficient application and is currently used for several electronic products. FinFET technology incorporates new technologies in the manufacturing processes that may generate new defect topologies which need to be considered during test generation. This paper analyzes the electrical behavior of full open gate defects, i.e., a transistor gate with infinite resistance. It is shown that classical models, called single open (SO) and interconnect open (IO), that have been proposed in the past for CMOS technology are not sufficient in FinFET technology. The modern FinFET-based logic cells using multifin and multifinger design techniques give rise to new specific defect topologies called ``subset full open gate defect.'' The static and dynamic electrical behaviors of the two new topologies, subset SO (SOsub) and subset IO ( IOsub), are analyzed, and the detectability of the defect in the context of Boolean testing and delay testing is derived. The detectability is analyzed taking into account process variation, temperature, and power supply control.
- 23 February 2018
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 34 (2) , 123-134
Detectability Challenges of Bridge Defects in FinFET Based Logic Cells
- 23 February 2018
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 34 (2) , 123-134
Detectability Challenges of Bridge Defects in FinFET Based Logic Cells
- 6 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 16 (3) , 417-430
Influence of Body-Biasing, Supply Voltage, and Temperature on the Detection of Resistive Short Defects in FDSOI Technology
This paper presents an in-depth analysis of the impact of body-biasing, supply voltage and temperature on the detection of resistive short defects in FDSOI technology. Three types of short defects are considered for our investigation, namely resistive short to ground terminal (GND), resistive short to power supply terminal (VDD) and inter-gate resistive bridging defect. The two implementation options offered by the technology, i.e. Low VT (LVT) and Regular VT (RVT) devices are also studied. Defect detectability is evaluated in the context of logic test using the concept of critical resistance. The optimal body-biasing, supply voltage and temperature settings to achieve the maximum defect coverage are determined through HSPICE simulations using a didactic circuit implemented with 28nm UTBB FDSOI gate library. An analytical analysis is also proposed based on the ON-resistance model of P and N networks, which permits to evaluate the value of the critical resistance without performing fault simulations. In addition, this work quantifies the individual as well as the combined improvements in detection brought by body-biasing, supply voltage and temperature settings for the different defect types and different implementations.
- 6 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 16 (3) , 417-430
Influence of Body-Biasing, Supply Voltage, and Temperature on the Detection of Resistive Short Defects in FDSOI Technology
This paper presents an in-depth analysis of the impact of body-biasing, supply voltage and temperature on the detection of resistive short defects in FDSOI technology. Three types of short defects are considered for our investigation, namely resistive short to ground terminal (GND), resistive short to power supply terminal (VDD) and inter-gate resistive bridging defect. The two implementation options offered by the technology, i.e. Low VT (LVT) and Regular VT (RVT) devices are also studied. Defect detectability is evaluated in the context of logic test using the concept of critical resistance. The optimal body-biasing, supply voltage and temperature settings to achieve the maximum defect coverage are determined through HSPICE simulations using a didactic circuit implemented with 28nm UTBB FDSOI gate library. An analytical analysis is also proposed based on the ON-resistance model of P and N networks, which permits to evaluate the value of the critical resistance without performing fault simulations. In addition, this work quantifies the individual as well as the combined improvements in detection brought by body-biasing, supply voltage and temperature settings for the different defect types and different implementations.
- Open Access
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10817735,p. 177-182
MIRID: Mixed-Mode IR-Drop Induced Delay Simulator
IR-drop effects are increasingly relevant in context of both design and test. We introduce the event-driven simulator MIRID that calculates the impact of IR-drop to the circuit timing. MIRID performs the simulation on two abstraction levels: timing effects in the gate-level net-list, current and voltage waveform propagation in the electrical model of the power-distribution network (PDN). Switching events at the logic gates are forwarded to the electrical model, where induced currents and their impact on the neighboring PDN nodes are computed. From this information, values of voltages at the Vdd and ground terminals of logic gates are determined, which in turn are used to calculate accurate switching delays of the gates. MIRID supports a generic interface to electrical models, allowing for a seamless integration of arbitrary models of PDN and gate timing. We report experiments based on a simple PDN model that was introduced previously and incorporates a pre-characterized library. The simulation accuracy is validated by matching the results from MIRID and SPICE.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10817735,p. 177-182
Open AccessMIRID: Mixed-Mode IR-Drop Induced Delay Simulator
IR-drop effects are increasingly relevant in context of both design and test. We introduce the event-driven simulator MIRID that calculates the impact of IR-drop to the circuit timing. MIRID performs the simulation on two abstraction levels: timing effects in the gate-level net-list, current and voltage waveform propagation in the electrical model of the power-distribution network (PDN). Switching events at the logic gates are forwarded to the electrical model, where induced currents and their impact on the neighboring PDN nodes are computed. From this information, values of voltages at the Vdd and ground terminals of logic gates are determined, which in turn are used to calculate accurate switching delays of the gates. MIRID supports a generic interface to electrical models, allowing for a seamless integration of arbitrary models of PDN and gate timing. We report experiments based on a simple PDN model that was introduced previously and incorporates a pre-characterized library. The simulation accuracy is validated by matching the results from MIRID and SPICE.
- Open Access
- 8 February 2011
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 27 (3) , 335-350
Digital Test Method for Embedded Converters with Unknown-Phase Harmonics
- 8 February 2011
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 27 (3) , 335-350
Open AccessDigital Test Method for Embedded Converters with Unknown-Phase Harmonics
- 1 April 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 199-203
LH-Bist for digital correction of ADC offset
In this paper, we show that it is possible to use built-in-self-test circuitry to correct some errors of the ADC under test. We take the example of the LH-BIST architecture we have previously developed to measure the ADC offset value. The interest of LH-BIST architecture is that one of its registers is directly connected to the output of the convert. Hence, this register can be use to digitally modify the running code of ADC according to offset value extract by this very LH-BIST circuitry.
- 1 April 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 199-203
LH-Bist for digital correction of ADC offset
In this paper, we show that it is possible to use built-in-self-test circuitry to correct some errors of the ADC under test. We take the example of the LH-BIST architecture we have previously developed to measure the ADC offset value. The interest of LH-BIST architecture is that one of its registers is directly connected to the output of the convert. Hence, this register can be use to digitally modify the running code of ADC according to offset value extract by this very LH-BIST circuitry.
- 10 October 2007
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 23 (6) , 497-512
Built-In Self-Test of Field Programmable Analog Arrays based on Transient Response Analysis
- 10 October 2007
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 23 (6) , 497-512
Built-In Self-Test of Field Programmable Analog Arrays based on Transient Response Analysis