Minjae Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Minjae Lee has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Kang-Yoon Lee
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
20 shared publications - Keum Cheol Hwang
Sungkyunkwan University
18 shared publications - Youngoo Yang
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
18 shared publications - Sewon Lee
School of Electrical Engineering and Computer Science, Gwangju Institute of Science and Technology, Buk-gu, Gwangju, South Korea
10 shared publications - YoungGun Pu
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
10 shared publications - Sang-Sun Yoo
SKAIChips, Suwon 16571, Republic of Korea
9 shared publications
Latest Publications
- Open Access
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 86190-86200
An 8-bit 600-MS/s Three-Comparator SAR ADC With MUX-Delay Exclusion and LSB Averaging
An 8-bit 600-MS/s three-comparator SAR ADC is presented that addresses the MUX-induced delay penalty associated with background comparator-swapping calibration. A MUX-delay exclusion techniques are proposed for the SAR loop, eliminating the MUX-induced overhead of the prior three-comparator SAR architecture and improving the conversion speed. Furthermore, an LSB averaging technique is introduced that reuses calibration data to reduce comparator noise and to mitigate the input parasitic capacitance of the three-comparator structure without additional decisions or sizing overhead. Fabricated in a 28-nm CMOS LP process, the prototype occupies 0.0024 mm2 and consumes 1.07 mW from a 1.0-V supply. Measurement results show an SNDR of 44.67 dB and an SFDR of 59.58 dB, achieving a Walden FoM of 12.8 fJ/conversion-step.
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 86190-86200
Open AccessAn 8-bit 600-MS/s Three-Comparator SAR ADC With MUX-Delay Exclusion and LSB Averaging
An 8-bit 600-MS/s three-comparator SAR ADC is presented that addresses the MUX-induced delay penalty associated with background comparator-swapping calibration. A MUX-delay exclusion techniques are proposed for the SAR loop, eliminating the MUX-induced overhead of the prior three-comparator SAR architecture and improving the conversion speed. Furthermore, an LSB averaging technique is introduced that reuses calibration data to reduce comparator noise and to mitigate the input parasitic capacitance of the three-comparator structure without additional decisions or sizing overhead. Fabricated in a 28-nm CMOS LP process, the prototype occupies 0.0024 mm2 and consumes 1.07 mW from a 1.0-V supply. Measurement results show an SNDR of 44.67 dB and an SFDR of 59.58 dB, achieving a Walden FoM of 12.8 fJ/conversion-step.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (3) , 1655-1668
Design and Analysis of a Low-Jitter High-Gain Latch-Based Time Amplifier
This paper presents design and analysis of a latch-based time amplifier (TA). While prior studies have primarily focused on TA gain and output characteristics, this work extends the analysis to include input-referred jitter, input dynamic range, latency, and gain behavior. Analytical equations are derived to facilitate comparisons with other TA architectures, offering insights into the performance trade-off of latch-based TA. The proposed models are validated through both simulations and measurements. A prototype latch-based TA is fabricated in a 28-nm CMOS LP process to demonstrate the effectiveness of the analysis.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (3) , 1655-1668
Design and Analysis of a Low-Jitter High-Gain Latch-Based Time Amplifier
This paper presents design and analysis of a latch-based time amplifier (TA). While prior studies have primarily focused on TA gain and output characteristics, this work extends the analysis to include input-referred jitter, input dynamic range, latency, and gain behavior. Analytical equations are derived to facilitate comparisons with other TA architectures, offering insights into the performance trade-off of latch-based TA. The proposed models are validated through both simulations and measurements. A prototype latch-based TA is fabricated in a 28-nm CMOS LP process to demonstrate the effectiveness of the analysis.
- 30 August 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 165
A 13 bit 4MS/s SAR ADC with energy-efficient bidirectional delay generation
- 30 August 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 165
A 13 bit 4MS/s SAR ADC with energy-efficient bidirectional delay generation
- Open Access
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 66458-66467
A 16.8 fJ/c-s 8 b 500 MS/s Asynchronous Three-Comparator SAR ADC With Background Comparator-Swapping Offset Calibration in 28 nm CMOS LPP
This paper presents a novel comparator-swapping background offset calibration method for SAR ADCs, addressing the limitations of previous calibration techniques. The proposed method uses three comparators to eliminate reset time and calibrates offset mismatch based on the LSB conversion, leading to rapid offset convergence and reduced dependence on input signal statistics. By alternating the roles of the comparators and eliminating the need for an additional calibration cycle, the method achieves efficient calibration without the overhead of extra reference comparators. A prototype 8-bit SAR ADC implemented in a 28 nm CMOS LPP process demonstrates the effectiveness of the proposed technique, achieving a measured SNDR of 44.3 dB and SFDR of 58.4 dB at 500 MS/s, with a power consumption of 1.13 mW. The ADC occupies only 0.0033 mm², with a Walden FoM of 16.8 fJ/conversion-step. The results show that the proposed calibration method is competitive with state-of-the-art techniques, offering a highly accurate and efficient solution for background offset mismatch calibration in SAR ADCs.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 66458-66467
Open AccessA 16.8 fJ/c-s 8 b 500 MS/s Asynchronous Three-Comparator SAR ADC With Background Comparator-Swapping Offset Calibration in 28 nm CMOS LPP
This paper presents a novel comparator-swapping background offset calibration method for SAR ADCs, addressing the limitations of previous calibration techniques. The proposed method uses three comparators to eliminate reset time and calibrates offset mismatch based on the LSB conversion, leading to rapid offset convergence and reduced dependence on input signal statistics. By alternating the roles of the comparators and eliminating the need for an additional calibration cycle, the method achieves efficient calibration without the overhead of extra reference comparators. A prototype 8-bit SAR ADC implemented in a 28 nm CMOS LPP process demonstrates the effectiveness of the proposed technique, achieving a measured SNDR of 44.3 dB and SFDR of 58.4 dB at 500 MS/s, with a power consumption of 1.13 mW. The ADC occupies only 0.0033 mm², with a Walden FoM of 16.8 fJ/conversion-step. The results show that the proposed calibration method is competitive with state-of-the-art techniques, offering a highly accurate and efficient solution for background offset mismatch calibration in SAR ADCs.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2558-2567
A 2.72-fJ/Conversion-Step 13-bit SAR ADC With Wide Common-Mode Complementary Split Pre-Amplifier Comparator and Grounded-Finger CDAC
This article presents a compact 13-bit 2-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) designed to enhance energy efficiency under various comparator input common-mode voltage scenarios. The proposed comparator structure features a complementary split pre-amplifier to extend the input common-mode range, resulting in an SNDR drop of approximately 1 dB even at a near 0-V ADC input common-mode voltage of 0.038 V. Furthermore, the proposed grounded-finger capacitive digital-to-analog converter (CDAC) reduces the impact of hard-to-scale fringe capacitance with a regular structure in order to reduce the number of CDAC elements and area. Utilizing these techniques, the prototype SAR ADC implemented in a 65-nm CMOS LP process achieves an uncalibrated integral non-linearity (INL) of 1.07 LSB, an 87.4% reduction in elements, and 70.6-dB SNDR in a 0.0372 mm $^2$ , consuming only 15.1 $\mu$ W at 0.75 V that results in a Walden figure of merit (FoM $_\text{W}$ ) of 2.72 fJ/conversion-step.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2558-2567
A 2.72-fJ/Conversion-Step 13-bit SAR ADC With Wide Common-Mode Complementary Split Pre-Amplifier Comparator and Grounded-Finger CDAC
This article presents a compact 13-bit 2-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) designed to enhance energy efficiency under various comparator input common-mode voltage scenarios. The proposed comparator structure features a complementary split pre-amplifier to extend the input common-mode range, resulting in an SNDR drop of approximately 1 dB even at a near 0-V ADC input common-mode voltage of 0.038 V. Furthermore, the proposed grounded-finger capacitive digital-to-analog converter (CDAC) reduces the impact of hard-to-scale fringe capacitance with a regular structure in order to reduce the number of CDAC elements and area. Utilizing these techniques, the prototype SAR ADC implemented in a 65-nm CMOS LP process achieves an uncalibrated integral non-linearity (INL) of 1.07 LSB, an 87.4% reduction in elements, and 70.6-dB SNDR in a 0.0372 mm $^2$ , consuming only 15.1 $\mu$ W at 0.75 V that results in a Walden figure of merit (FoM $_\text{W}$ ) of 2.72 fJ/conversion-step.
- Open Access
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 98466-98479
Advancing Baud Rate Receivers: On Multiple CTLE Parameters Background Adaptation
The continuous-time linear equalizer (CTLE) is a key component in receivers for improving the achievable bit error rate. Available CTLE background adaptation methods are limited to adjusting a single parameter, such as the source resistance or capacitance. In contrast, this paper presents a background adaptation method capable of concurrently finding near-optimal source resistance and capacitance values for multiple CTLE configurations in baud rate communication. Moreover, this paper presents a sequential method for adjusting both short and long-tail CTLE parameters, ensuring effective system control. The multiple loop interactions are considered with recent DSP-based receivers main building blocks, such as the clock and data recovery (CDR) and automatic gain control (AGC). A relatively simple logic based on inter-symbol interference (ISI) taps is employed, similar to conventional Mueller-Muller methods, which does not impose significant hardware overhead compared to previous publications. Simulations using real channel models demonstrate the proposed adaptation’s performance across a wide range of insertion loss channels and various modulations.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 98466-98479
Open AccessAdvancing Baud Rate Receivers: On Multiple CTLE Parameters Background Adaptation
The continuous-time linear equalizer (CTLE) is a key component in receivers for improving the achievable bit error rate. Available CTLE background adaptation methods are limited to adjusting a single parameter, such as the source resistance or capacitance. In contrast, this paper presents a background adaptation method capable of concurrently finding near-optimal source resistance and capacitance values for multiple CTLE configurations in baud rate communication. Moreover, this paper presents a sequential method for adjusting both short and long-tail CTLE parameters, ensuring effective system control. The multiple loop interactions are considered with recent DSP-based receivers main building blocks, such as the clock and data recovery (CDR) and automatic gain control (AGC). A relatively simple logic based on inter-symbol interference (ISI) taps is employed, similar to conventional Mueller-Muller methods, which does not impose significant hardware overhead compared to previous publications. Simulations using real channel models demonstrate the proposed adaptation’s performance across a wide range of insertion loss channels and various modulations.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11602-11611
A Fully Differential Direct Sampling Touch Screen Readout With a Touch Vector Calibration for Ultrathin Organic Light-Emitting Diode Display
This article presents a touch screen panel (TSP) readout IC (ROIC) for an ultrathin organic light-emitting diode (OLED) display, where display noise injection is severely increased. We adopted a fully differential (FD) and direct sampling receiver (RX) structure that supports digital in-phase and quadrature (IQ) demodulation to improve tolerance over display noise harmonics intermodulation. Furthermore, we present a touch vector calibration technique that reduces the digital processing burden originating from processing FD touch signals. The proposed IC consists of two chips fabricated in 55 and 130 nm CMOS processes and then packaged into a single package. The signal-to-noise ratio (SNR) is 54.03 dB with a 240 Hz frame rate for the 6.1-inch 16 × 34 ultrathin OLED TSP, while consuming 65.65 mW.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11602-11611
A Fully Differential Direct Sampling Touch Screen Readout With a Touch Vector Calibration for Ultrathin Organic Light-Emitting Diode Display
This article presents a touch screen panel (TSP) readout IC (ROIC) for an ultrathin organic light-emitting diode (OLED) display, where display noise injection is severely increased. We adopted a fully differential (FD) and direct sampling receiver (RX) structure that supports digital in-phase and quadrature (IQ) demodulation to improve tolerance over display noise harmonics intermodulation. Furthermore, we present a touch vector calibration technique that reduces the digital processing burden originating from processing FD touch signals. The proposed IC consists of two chips fabricated in 55 and 130 nm CMOS processes and then packaged into a single package. The signal-to-noise ratio (SNR) is 54.03 dB with a 240 Hz frame rate for the 6.1-inch 16 × 34 ultrathin OLED TSP, while consuming 65.65 mW.
- Open Access
- 21 November 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (22)
Asynchronous SAR ADC with self‐timed track‐and‐hold
This paper presents an asynchronous SAR ADC featuring a self‐timed track‐and‐hold (STH) architecture. The design aims to address the common timing issue of divider‐based clock generation, where the fixed‐time track‐and‐hold (FTH) period often results in incomplete conversions due to prolonged conversion times time due to comparator metastability. To alleviate the degradation of the ENOB induced by these delays, the proposed STH method is introduced so that more conversion period is secured without requiring a high‐speed input clock. Based on measurements, the proposed STH method achieves up to 0.7 bit improvement over the conventional FTH approach as conversion time increases.
- 21 November 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (22)
Open AccessAsynchronous SAR ADC with self‐timed track‐and‐hold
This paper presents an asynchronous SAR ADC featuring a self‐timed track‐and‐hold (STH) architecture. The design aims to address the common timing issue of divider‐based clock generation, where the fixed‐time track‐and‐hold (FTH) period often results in incomplete conversions due to prolonged conversion times time due to comparator metastability. To alleviate the degradation of the ENOB induced by these delays, the proposed STH method is introduced so that more conversion period is secured without requiring a high‐speed input clock. Based on measurements, the proposed STH method achieves up to 0.7 bit improvement over the conventional FTH approach as conversion time increases.