Sewon Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sewon Lee has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Minjae Lee
Gwangju Institute of Science and Technology
10 shared publications - Siheon Seong
Gwangju Institute of Science and Technology
4 shared publications - Sunghyun Bae
School of Electrical Engineering and Computer Science, Gwangju Institute of Science and Technology, Gwangju, South Korea
4 shared publications - Hyein Kang
School of Electrical Engineering and Computer Science, Gwangju Institute of Science and Technology, Gwangju, South Korea
3 shared publications Bonghyuk Park
Electronics and Telecommunications Research Institute, Yuseong-gu, Daejeon, South Korea
1 shared publication- Hyungyu Ju
The School of Electrical and Computer Science, Gwangju Institute of Science and Technology, Gwangju 61005, Korea
1 shared publication
Latest Publications
- Open Access
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 86190-86200
An 8-bit 600-MS/s Three-Comparator SAR ADC With MUX-Delay Exclusion and LSB Averaging
An 8-bit 600-MS/s three-comparator SAR ADC is presented that addresses the MUX-induced delay penalty associated with background comparator-swapping calibration. A MUX-delay exclusion techniques are proposed for the SAR loop, eliminating the MUX-induced overhead of the prior three-comparator SAR architecture and improving the conversion speed. Furthermore, an LSB averaging technique is introduced that reuses calibration data to reduce comparator noise and to mitigate the input parasitic capacitance of the three-comparator structure without additional decisions or sizing overhead. Fabricated in a 28-nm CMOS LP process, the prototype occupies 0.0024 mm2 and consumes 1.07 mW from a 1.0-V supply. Measurement results show an SNDR of 44.67 dB and an SFDR of 59.58 dB, achieving a Walden FoM of 12.8 fJ/conversion-step.
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 86190-86200
Open AccessAn 8-bit 600-MS/s Three-Comparator SAR ADC With MUX-Delay Exclusion and LSB Averaging
An 8-bit 600-MS/s three-comparator SAR ADC is presented that addresses the MUX-induced delay penalty associated with background comparator-swapping calibration. A MUX-delay exclusion techniques are proposed for the SAR loop, eliminating the MUX-induced overhead of the prior three-comparator SAR architecture and improving the conversion speed. Furthermore, an LSB averaging technique is introduced that reuses calibration data to reduce comparator noise and to mitigate the input parasitic capacitance of the three-comparator structure without additional decisions or sizing overhead. Fabricated in a 28-nm CMOS LP process, the prototype occupies 0.0024 mm2 and consumes 1.07 mW from a 1.0-V supply. Measurement results show an SNDR of 44.67 dB and an SFDR of 59.58 dB, achieving a Walden FoM of 12.8 fJ/conversion-step.
- 30 August 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 165
A 13 bit 4MS/s SAR ADC with energy-efficient bidirectional delay generation
- 30 August 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 165
A 13 bit 4MS/s SAR ADC with energy-efficient bidirectional delay generation
- Open Access
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 66458-66467
A 16.8 fJ/c-s 8 b 500 MS/s Asynchronous Three-Comparator SAR ADC With Background Comparator-Swapping Offset Calibration in 28 nm CMOS LPP
This paper presents a novel comparator-swapping background offset calibration method for SAR ADCs, addressing the limitations of previous calibration techniques. The proposed method uses three comparators to eliminate reset time and calibrates offset mismatch based on the LSB conversion, leading to rapid offset convergence and reduced dependence on input signal statistics. By alternating the roles of the comparators and eliminating the need for an additional calibration cycle, the method achieves efficient calibration without the overhead of extra reference comparators. A prototype 8-bit SAR ADC implemented in a 28 nm CMOS LPP process demonstrates the effectiveness of the proposed technique, achieving a measured SNDR of 44.3 dB and SFDR of 58.4 dB at 500 MS/s, with a power consumption of 1.13 mW. The ADC occupies only 0.0033 mm², with a Walden FoM of 16.8 fJ/conversion-step. The results show that the proposed calibration method is competitive with state-of-the-art techniques, offering a highly accurate and efficient solution for background offset mismatch calibration in SAR ADCs.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 66458-66467
Open AccessA 16.8 fJ/c-s 8 b 500 MS/s Asynchronous Three-Comparator SAR ADC With Background Comparator-Swapping Offset Calibration in 28 nm CMOS LPP
This paper presents a novel comparator-swapping background offset calibration method for SAR ADCs, addressing the limitations of previous calibration techniques. The proposed method uses three comparators to eliminate reset time and calibrates offset mismatch based on the LSB conversion, leading to rapid offset convergence and reduced dependence on input signal statistics. By alternating the roles of the comparators and eliminating the need for an additional calibration cycle, the method achieves efficient calibration without the overhead of extra reference comparators. A prototype 8-bit SAR ADC implemented in a 28 nm CMOS LPP process demonstrates the effectiveness of the proposed technique, achieving a measured SNDR of 44.3 dB and SFDR of 58.4 dB at 500 MS/s, with a power consumption of 1.13 mW. The ADC occupies only 0.0033 mm², with a Walden FoM of 16.8 fJ/conversion-step. The results show that the proposed calibration method is competitive with state-of-the-art techniques, offering a highly accurate and efficient solution for background offset mismatch calibration in SAR ADCs.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2558-2567
A 2.72-fJ/Conversion-Step 13-bit SAR ADC With Wide Common-Mode Complementary Split Pre-Amplifier Comparator and Grounded-Finger CDAC
This article presents a compact 13-bit 2-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) designed to enhance energy efficiency under various comparator input common-mode voltage scenarios. The proposed comparator structure features a complementary split pre-amplifier to extend the input common-mode range, resulting in an SNDR drop of approximately 1 dB even at a near 0-V ADC input common-mode voltage of 0.038 V. Furthermore, the proposed grounded-finger capacitive digital-to-analog converter (CDAC) reduces the impact of hard-to-scale fringe capacitance with a regular structure in order to reduce the number of CDAC elements and area. Utilizing these techniques, the prototype SAR ADC implemented in a 65-nm CMOS LP process achieves an uncalibrated integral non-linearity (INL) of 1.07 LSB, an 87.4% reduction in elements, and 70.6-dB SNDR in a 0.0372 mm $^2$ , consuming only 15.1 $\mu$ W at 0.75 V that results in a Walden figure of merit (FoM $_\text{W}$ ) of 2.72 fJ/conversion-step.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2558-2567
A 2.72-fJ/Conversion-Step 13-bit SAR ADC With Wide Common-Mode Complementary Split Pre-Amplifier Comparator and Grounded-Finger CDAC
This article presents a compact 13-bit 2-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) designed to enhance energy efficiency under various comparator input common-mode voltage scenarios. The proposed comparator structure features a complementary split pre-amplifier to extend the input common-mode range, resulting in an SNDR drop of approximately 1 dB even at a near 0-V ADC input common-mode voltage of 0.038 V. Furthermore, the proposed grounded-finger capacitive digital-to-analog converter (CDAC) reduces the impact of hard-to-scale fringe capacitance with a regular structure in order to reduce the number of CDAC elements and area. Utilizing these techniques, the prototype SAR ADC implemented in a 65-nm CMOS LP process achieves an uncalibrated integral non-linearity (INL) of 1.07 LSB, an 87.4% reduction in elements, and 70.6-dB SNDR in a 0.0372 mm $^2$ , consuming only 15.1 $\mu$ W at 0.75 V that results in a Walden figure of merit (FoM $_\text{W}$ ) of 2.72 fJ/conversion-step.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11602-11611
A Fully Differential Direct Sampling Touch Screen Readout With a Touch Vector Calibration for Ultrathin Organic Light-Emitting Diode Display
This article presents a touch screen panel (TSP) readout IC (ROIC) for an ultrathin organic light-emitting diode (OLED) display, where display noise injection is severely increased. We adopted a fully differential (FD) and direct sampling receiver (RX) structure that supports digital in-phase and quadrature (IQ) demodulation to improve tolerance over display noise harmonics intermodulation. Furthermore, we present a touch vector calibration technique that reduces the digital processing burden originating from processing FD touch signals. The proposed IC consists of two chips fabricated in 55 and 130 nm CMOS processes and then packaged into a single package. The signal-to-noise ratio (SNR) is 54.03 dB with a 240 Hz frame rate for the 6.1-inch 16 × 34 ultrathin OLED TSP, while consuming 65.65 mW.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11602-11611
A Fully Differential Direct Sampling Touch Screen Readout With a Touch Vector Calibration for Ultrathin Organic Light-Emitting Diode Display
This article presents a touch screen panel (TSP) readout IC (ROIC) for an ultrathin organic light-emitting diode (OLED) display, where display noise injection is severely increased. We adopted a fully differential (FD) and direct sampling receiver (RX) structure that supports digital in-phase and quadrature (IQ) demodulation to improve tolerance over display noise harmonics intermodulation. Furthermore, we present a touch vector calibration technique that reduces the digital processing burden originating from processing FD touch signals. The proposed IC consists of two chips fabricated in 55 and 130 nm CMOS processes and then packaged into a single package. The signal-to-noise ratio (SNR) is 54.03 dB with a 240 Hz frame rate for the 6.1-inch 16 × 34 ultrathin OLED TSP, while consuming 65.65 mW.
- Open Access
- 21 November 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (22)
Asynchronous SAR ADC with self‐timed track‐and‐hold
This paper presents an asynchronous SAR ADC featuring a self‐timed track‐and‐hold (STH) architecture. The design aims to address the common timing issue of divider‐based clock generation, where the fixed‐time track‐and‐hold (FTH) period often results in incomplete conversions due to prolonged conversion times time due to comparator metastability. To alleviate the degradation of the ENOB induced by these delays, the proposed STH method is introduced so that more conversion period is secured without requiring a high‐speed input clock. Based on measurements, the proposed STH method achieves up to 0.7 bit improvement over the conventional FTH approach as conversion time increases.
- 21 November 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (22)
Open AccessAsynchronous SAR ADC with self‐timed track‐and‐hold
This paper presents an asynchronous SAR ADC featuring a self‐timed track‐and‐hold (STH) architecture. The design aims to address the common timing issue of divider‐based clock generation, where the fixed‐time track‐and‐hold (FTH) period often results in incomplete conversions due to prolonged conversion times time due to comparator metastability. To alleviate the degradation of the ENOB induced by these delays, the proposed STH method is introduced so that more conversion period is secured without requiring a high‐speed input clock. Based on measurements, the proposed STH method achieves up to 0.7 bit improvement over the conventional FTH approach as conversion time increases.
- Open Access
- 22 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 104323-104332
A 13-Bit 1-MS/s SAR ADC With Completion-Aware Background Capacitor Mismatch Calibration
This paper introduces a completion-aware background sequential capacitor mismatch calibration technique for SAR ADC. The proposed method sequentially corrects capacitor mismatch from the lower to the upper bits in the CDAC. This calibration method can automatically detect when calibration is complete, thereby improving power efficiency by terminating calibration activities. This approach mitigates the trade-off between adaptation speed and calibration code variation, thereby enhancing correction speed. Moreover, the sequential calibration demonstrates stability in unpredictable input environments. The ADC developed in this study utilizes 55-nm LP CMOS technology, operates at a speed of 1 MS/s, and consumes 43 μW of power. It achieves peak DNL of +0.83/-0.62 LSB and INL of +1.89/-1.13 LSB. Furthermore, it achieves a mean SNDR of 67.9 dB and SFDR of 82.5 dB, resulting in a FoM of 19.59 fJ/conv.-step.
- 22 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 104323-104332
Open AccessA 13-Bit 1-MS/s SAR ADC With Completion-Aware Background Capacitor Mismatch Calibration
This paper introduces a completion-aware background sequential capacitor mismatch calibration technique for SAR ADC. The proposed method sequentially corrects capacitor mismatch from the lower to the upper bits in the CDAC. This calibration method can automatically detect when calibration is complete, thereby improving power efficiency by terminating calibration activities. This approach mitigates the trade-off between adaptation speed and calibration code variation, thereby enhancing correction speed. Moreover, the sequential calibration demonstrates stability in unpredictable input environments. The ADC developed in this study utilizes 55-nm LP CMOS technology, operates at a speed of 1 MS/s, and consumes 43 μW of power. It achieves peak DNL of +0.83/-0.62 LSB and INL of +1.89/-1.13 LSB. Furthermore, it achieves a mean SNDR of 67.9 dB and SFDR of 82.5 dB, resulting in a FoM of 19.59 fJ/conv.-step.
- Open Access
- 14 April 2023
- Published by MDPI AG in Electronics
- Vol. 12 (8) , 1863
A Three-Step Tapered Bit Period SAR ADC Using Area-Efficient Clock Generation
A three-step tapered bit period asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) is proposed to reduce the total DAC settling time by 47.7% compared to the non-tapered conversion time with less design overhead. Unlike conventional approaches, the SAR settling time analysis with both reference buffer output impedance and hardware overhead is first analyzed in each conversion step, which demonstrates that the three-step tapered bit period approach is the most time- and hardware efficient in our design. Additionally, area-efficient three-step clock generation is proposed by sharing resistors for delay generation, resulting in a small area increase of only 20.4% compared to the non-tapered clock generation. As a result, the proposed technique is used to reduce the reference buffer’s power and increase the sampling frequency. The maximum allowed output impedance of the reference buffer for SFDR > 92 dB becomes larger than that of the non-tapered design by 200 , translated to a sampling frequency increase from 6 MHz to 8 MHz in our design. The proposed three-step tapered bit period using an area-efficient clock generator was designed in a 55 nm CMOS process. The clock generator occupies 0.00081 mm out of 1143 m × 81 m overall size. The power consumption of the 8 MS/s 12-bit SAR ADC with proposed clock generation is 128.91 W when under 1 V supply.- 14 April 2023
- Published by MDPI AG in Electronics
- Vol. 12 (8) , 1863
Open AccessA Three-Step Tapered Bit Period SAR ADC Using Area-Efficient Clock Generation
A three-step tapered bit period asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) is proposed to reduce the total DAC settling time by 47.7% compared to the non-tapered conversion time with less design overhead. Unlike conventional approaches, the SAR settling time analysis with both reference buffer output impedance and hardware overhead is first analyzed in each conversion step, which demonstrates that the three-step tapered bit period approach is the most time- and hardware efficient in our design. Additionally, area-efficient three-step clock generation is proposed by sharing resistors for delay generation, resulting in a small area increase of only 20.4% compared to the non-tapered clock generation. As a result, the proposed technique is used to reduce the reference buffer’s power and increase the sampling frequency. The maximum allowed output impedance of the reference buffer for SFDR > 92 dB becomes larger than that of the non-tapered design by 200 , translated to a sampling frequency increase from 6 MHz to 8 MHz in our design. The proposed three-step tapered bit period using an area-efficient clock generator was designed in a 55 nm CMOS process. The clock generator occupies 0.00081 mm out of 1143 m × 81 m overall size. The power consumption of the 8 MS/s 12-bit SAR ADC with proposed clock generation is 128.91 W when under 1 V supply. - Open Access
Self Capacitance Mismatch Calibration Technique for Fully-Differential Touch Screen Panel Self Capacitance Sensing System
This paper presents a fully-differential touch screen panel (TSP) self-capacitance sensing (SCS) system with a self-capacitance mismatch calibration technique. Due to the self-capacitance mismatch of TSP, the analog front-end (AFE) of the receiver (RX) circuit suffers from dynamic range degradation and gain limitations, which lead to the signal-to-noise ratio (SNR) loss for the TSP SCS system. The proposed calibration introduces the difference in input resistance and the driving amplifier’s strength between the fully-differential input. Thus, the mismatch effect is efficiently relieved in terms of area and power consumption. The proposed calibration restores the SNR by dB even under the worst self-capacitance mismatch case.Open AccessSelf Capacitance Mismatch Calibration Technique for Fully-Differential Touch Screen Panel Self Capacitance Sensing System
This paper presents a fully-differential touch screen panel (TSP) self-capacitance sensing (SCS) system with a self-capacitance mismatch calibration technique. Due to the self-capacitance mismatch of TSP, the analog front-end (AFE) of the receiver (RX) circuit suffers from dynamic range degradation and gain limitations, which lead to the signal-to-noise ratio (SNR) loss for the TSP SCS system. The proposed calibration introduces the difference in input resistance and the driving amplifier’s strength between the fully-differential input. Thus, the mismatch effect is efficiently relieved in terms of area and power consumption. The proposed calibration restores the SNR by dB even under the worst self-capacitance mismatch case. - Open Access
- 5 November 2020
- Published by MDPI AG in Electronics
- Vol. 9 (11) , 1854
A 12-bit 40-MS/s SAR ADC with Calibration-Less Switched Capacitive Reference Driver
This paper presents a switched capacitive reference driver (SCRD) with a low-energy switching scheme. In order to reduce the performance degradation resulting from a signal-dependent voltage drop in a capacitive reference driver (CRD) without increasing the capacitance (CREF) of a CRD, the proposed SCRD utilizes the CRD for LSB conversion cycles. In MSB conversion cycles, a supply voltage is used as a reference voltage to save on area and power consumption. As such, the proposed SCRD significantly relaxes the required CREF, and does not necessitate bit weight calibration or compensation requiring an auxiliary capacitor-based digital-to-analog converter (CDAC). To evaluate the proposed SCRD, a prototype 12-bit 40-MS/s SAR ADC is fabricated in a 65 nm CMOS process. With near Nyquist frequency, the measured spurious-free dynamic range (SFDR) of the SAR ADC with the SCRD is 80.6 dB, which is about a 16 dB improvement from the SFDR of a SAR ADC with a CRD only.
- 5 November 2020
- Published by MDPI AG in Electronics
- Vol. 9 (11) , 1854
Open AccessA 12-bit 40-MS/s SAR ADC with Calibration-Less Switched Capacitive Reference Driver
This paper presents a switched capacitive reference driver (SCRD) with a low-energy switching scheme. In order to reduce the performance degradation resulting from a signal-dependent voltage drop in a capacitive reference driver (CRD) without increasing the capacitance (CREF) of a CRD, the proposed SCRD utilizes the CRD for LSB conversion cycles. In MSB conversion cycles, a supply voltage is used as a reference voltage to save on area and power consumption. As such, the proposed SCRD significantly relaxes the required CREF, and does not necessitate bit weight calibration or compensation requiring an auxiliary capacitor-based digital-to-analog converter (CDAC). To evaluate the proposed SCRD, a prototype 12-bit 40-MS/s SAR ADC is fabricated in a 65 nm CMOS process. With near Nyquist frequency, the measured spurious-free dynamic range (SFDR) of the SAR ADC with the SCRD is 80.6 dB, which is about a 16 dB improvement from the SFDR of a SAR ADC with a CRD only.