Robert Charles Wimpory
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Robert Charles Wimpory has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Mirko Boin
Dept. Microstructure & Residual Stress Analysis (CE‐AME) Helmholtz‐Zentrum Berlin für Materialien und Energie (HZB) Berlin Germany
7 shared publications - Jeremy S. Robinson
School of Engineering, University of Limerick, Limerick, Ireland
4 shared publications - Michael Hofmann
Heinz Maier-Leibnitz Zentrum (MLZ), Technische Universität München (TUM), 85748 Garching bei München, Germany
4 shared publications - Carsten Ohms
European Commission, Joint Research Centre, Westerduinweg 3, 1755 LE Petten, The Netherlands
3 shared publications - Amir Mostafaei
Department of Mechanical, Materials and Aerospace Engineering, Illinois Institute of Technology, Chicago, USA
2 shared publications - Christopher E. Truman
Department of Mechanical Engineering, University of Bristol, Bristol, UK
2 shared publications
Latest Publications
- Open Access
- 24 August 2026
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 59 (5) , 1407-1419
Depth-resolved X-ray residual stress analysis on samples with cylindrically shaped surface topography
Angle- and energy-dispersive diffraction are applied to investigate the influence of the X-ray beam diameter on the results of residual stress analysis on a sample with an inhomogeneous surface topography. For sin 2 ψ measurements on parts of the surface featuring a cylindrical topography, modifications of the fundamental equation of X-ray stress analysis are proposed to correct the experimentally determined residual stresses for the rotational effect caused by the different orientation of the local principal stress coordinate system within the irradiated part of the sample. It is shown that the hoop and longitudinal stress components require different treatments in this respect. For the hoop stress component a correction factor is proposed which considers the variation in the illuminated surface area during the ψ tilt of the sample. Correction of the longitudinal stress component requires knowledge of the hoop stress component, which affects the slope of the sin 2 ψ regression line and thus partially acts as a normal stress component. For cases in which ψ tilting is not possible for geometric reasons, the applicability of the transverse contraction method is discussed. Experimental verification is carried out on a ferritic steel sample into which grooves of the same diameter were milled to different depths, resulting in different central angles.
- 24 August 2026
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 59 (5) , 1407-1419
Open AccessDepth-resolved X-ray residual stress analysis on samples with cylindrically shaped surface topography
Angle- and energy-dispersive diffraction are applied to investigate the influence of the X-ray beam diameter on the results of residual stress analysis on a sample with an inhomogeneous surface topography. For sin 2 ψ measurements on parts of the surface featuring a cylindrical topography, modifications of the fundamental equation of X-ray stress analysis are proposed to correct the experimentally determined residual stresses for the rotational effect caused by the different orientation of the local principal stress coordinate system within the irradiated part of the sample. It is shown that the hoop and longitudinal stress components require different treatments in this respect. For the hoop stress component a correction factor is proposed which considers the variation in the illuminated surface area during the ψ tilt of the sample. Correction of the longitudinal stress component requires knowledge of the hoop stress component, which affects the slope of the sin 2 ψ regression line and thus partially acts as a normal stress component. For cases in which ψ tilting is not possible for geometric reasons, the applicability of the transverse contraction method is discussed. Experimental verification is carried out on a ferritic steel sample into which grooves of the same diameter were milled to different depths, resulting in different central angles.
- 15 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Impact and Control of Residual Stresses in Ceramic Packages
An important challenge in ceramic and hybrid packaging is the joining of different materials within assemblies that demand complex functionality, high performance, and long-term reliability. Often, less attention is given to the fact that manufacturing processes such as co-firing, film deposition, and soldering generate residual stresses between the bonded materials. These stresses can further evolve due to relaxation effects during subsequent processing steps. Understanding the residual stress state is therefore essential, as it directly impacts the quality and performance of the final product throughout its lifecycle. Effective control of these stresses in industrial production requires reliable detection methods that offer both precision and practical applicability. In this context, three measurement techniques for assessing residual stress in ceramic components are presented and compared.
- 15 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Impact and Control of Residual Stresses in Ceramic Packages
An important challenge in ceramic and hybrid packaging is the joining of different materials within assemblies that demand complex functionality, high performance, and long-term reliability. Often, less attention is given to the fact that manufacturing processes such as co-firing, film deposition, and soldering generate residual stresses between the bonded materials. These stresses can further evolve due to relaxation effects during subsequent processing steps. Understanding the residual stress state is therefore essential, as it directly impacts the quality and performance of the final product throughout its lifecycle. Effective control of these stresses in industrial production requires reliable detection methods that offer both precision and practical applicability. In this context, three measurement techniques for assessing residual stress in ceramic components are presented and compared.
- 18 July 2022
- Published by Elsevier in Engineering Structures
- Vol. 267
In-depth residual stress analysis considering manufacturing process and cyclic loading of bolts
- 18 July 2022
- Published by Elsevier in Engineering Structures
- Vol. 267
In-depth residual stress analysis considering manufacturing process and cyclic loading of bolts
- Open Access
Characterizing Changes in Grain Growth, Mechanical Properties, and Transformation Properties in Differently Sintered and Annealed Binder-Jet 3D Printed 14M Ni–Mn–Ga Magnetic Shape Memory Alloys
Ni–Mn–Ga Heusler alloys are multifunctional materials that demonstrate macroscopic strain under an externally applied magnetic field through the motion of martensite twin boundaries within the microstructure. This study sought to comprehensively characterize the microstructural, mechanical, thermal, and magnetic properties near the solidus in binder-jet 3D printed 14M Ni50Mn30Ga20. Neutron diffraction data were analyzed to identify the martensite modulation and observe the grain size evolution in samples sintered at temperatures of 1080 °C and 1090 °C. Large clusters of high neutron-count pixels in samples sintered at 1090 °C were identified, suggesting Bragg diffraction of large grains (near doubling in size) compared to 1080 °C sintered samples. The grain size was confirmed through quantitative stereology of polished surfaces for differently sintered and heat-treated samples. Nanoindentation testing revealed a greater resistance to plasticity and a larger elastic modulus in 1090 °C sintered samples (relative density ~95%) compared to the samples sintered at 1080 °C (relative density ~80%). Martensitic transformation temperatures were lower for samples sintered at 1090 °C than 1080 °C, though a further heat treatment step could be added to tailor the transformation temperature. Microstructurally, twin variants ≤10 μm in width were observed and the presence of magnetic anisotropy was confirmed through magnetic force microscopy. This study indicates that a 10 °C sintering temperature difference can largely affect the microstructure and mechanical properties (including elastic modulus and hardness) while still allowing for the presence of magnetic twin variants in the resulting modulated martensite.
Open AccessCharacterizing Changes in Grain Growth, Mechanical Properties, and Transformation Properties in Differently Sintered and Annealed Binder-Jet 3D Printed 14M Ni–Mn–Ga Magnetic Shape Memory Alloys
Ni–Mn–Ga Heusler alloys are multifunctional materials that demonstrate macroscopic strain under an externally applied magnetic field through the motion of martensite twin boundaries within the microstructure. This study sought to comprehensively characterize the microstructural, mechanical, thermal, and magnetic properties near the solidus in binder-jet 3D printed 14M Ni50Mn30Ga20. Neutron diffraction data were analyzed to identify the martensite modulation and observe the grain size evolution in samples sintered at temperatures of 1080 °C and 1090 °C. Large clusters of high neutron-count pixels in samples sintered at 1090 °C were identified, suggesting Bragg diffraction of large grains (near doubling in size) compared to 1080 °C sintered samples. The grain size was confirmed through quantitative stereology of polished surfaces for differently sintered and heat-treated samples. Nanoindentation testing revealed a greater resistance to plasticity and a larger elastic modulus in 1090 °C sintered samples (relative density ~95%) compared to the samples sintered at 1080 °C (relative density ~80%). Martensitic transformation temperatures were lower for samples sintered at 1090 °C than 1080 °C, though a further heat treatment step could be added to tailor the transformation temperature. Microstructurally, twin variants ≤10 μm in width were observed and the presence of magnetic anisotropy was confirmed through magnetic force microscopy. This study indicates that a 10 °C sintering temperature difference can largely affect the microstructure and mechanical properties (including elastic modulus and hardness) while still allowing for the presence of magnetic twin variants in the resulting modulated martensite.
- Open Access
- 15 March 2022
- Published by Springer Nature in Experimental Mechanics
- Vol. 62 (8) , 1411-1420
Uphill Quenching to Reduce Residual Stress in Aluminium Alloy 7449 Hollow Structures
Background: Uphill quenching (UHQ) of heat treatable aluminium alloy components is a long established but rarely practiced or investigated method of reducing residual stresses. The efficacy of the technique has not been quantified on thin walled structures before and this investigation will address that deficiency.Objective: To quantify the impact of uphill quenching on thin walled structure with regards to residual stress and warpage, and compare and contrast to both quenching into cold water and a 30% polyalkylene glycol (PAG) solution.Methods: Rectilinear hollow boxes were made from the very high strength aerospace aluminium alloy 7449. These were heat treated and aged using a variety of processing methods including uphill quenching from -196 °C to 100 °C using steam. Residual stresses have been characterised using neutron and x-ray diffraction.Results: Compared to conventional quenching into cold water, both PAG and UHQ are shown to significantly lower the residual stresses. However, while PAG quenching results in a large uniform reduction in both residual stress and warpage, UHQ is much more localised and limited to regions adjacent to direct steam impingement. These regions are also warped. The depth of penetration of the stress relief during UHQ is shown to be 5 mm.Conclusions: While uphill quenching is shown to be capable of locally stress relieving an aluminium alloy, it is far less effective compared to PAG quenching.
- 15 March 2022
- Published by Springer Nature in Experimental Mechanics
- Vol. 62 (8) , 1411-1420
Open AccessUphill Quenching to Reduce Residual Stress in Aluminium Alloy 7449 Hollow Structures
Background: Uphill quenching (UHQ) of heat treatable aluminium alloy components is a long established but rarely practiced or investigated method of reducing residual stresses. The efficacy of the technique has not been quantified on thin walled structures before and this investigation will address that deficiency.Objective: To quantify the impact of uphill quenching on thin walled structure with regards to residual stress and warpage, and compare and contrast to both quenching into cold water and a 30% polyalkylene glycol (PAG) solution.Methods: Rectilinear hollow boxes were made from the very high strength aerospace aluminium alloy 7449. These were heat treated and aged using a variety of processing methods including uphill quenching from -196 °C to 100 °C using steam. Residual stresses have been characterised using neutron and x-ray diffraction.Results: Compared to conventional quenching into cold water, both PAG and UHQ are shown to significantly lower the residual stresses. However, while PAG quenching results in a large uniform reduction in both residual stress and warpage, UHQ is much more localised and limited to regions adjacent to direct steam impingement. These regions are also warped. The depth of penetration of the stress relief during UHQ is shown to be 5 mm.Conclusions: While uphill quenching is shown to be capable of locally stress relieving an aluminium alloy, it is far less effective compared to PAG quenching.
- Open Access
- 16 July 2021
- Published by ASME International
Comparison of Residual Stress Measurements on Single Bead-on-Plate Welds of a Martensitic Steel Using Neutron Diffraction
During the welding process, a material is subjected to thermal cycles with rapid heating and cooling rates resulting in residual stress in the weld and the base metal. The residual stress along with the phase transformations may affect the mechanical performance leading to premature failure of components. Therefore, it is critical to have a detailed knowledge of the residual stress
- 16 July 2021
- Published by ASME International
Open AccessComparison of Residual Stress Measurements on Single Bead-on-Plate Welds of a Martensitic Steel Using Neutron Diffraction
During the welding process, a material is subjected to thermal cycles with rapid heating and cooling rates resulting in residual stress in the weld and the base metal. The residual stress along with the phase transformations may affect the mechanical performance leading to premature failure of components. Therefore, it is critical to have a detailed knowledge of the residual stress
- Open Access
- 30 March 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 23 (7)
Scanning Manufacturing Parameters Determining the Residual Stress State in LPBF IN718 Small Parts
The influence of scan strategy on the residual stress (RS) state of an as‐built IN718 alloy produced by means of laser powder bed fusion (LPBF) is investigated. Two scan vector rotations (90°‐alternation and 67°‐rotation), each produced following two different scan vector lengths (long and short), are used to manufacture four rectangular prisms. Neutron diffraction (ND) and laboratory X‐ray diffraction (XRD) techniques are used to map the bulk and surface RS state, respectively. The distortion induced upon removal from the baseplate is measured via profilometry. XRD measurements show that the two long scan vector strategies lead to higher RS when compared with the equivalent short scan vector strategies. Also, the 67°‐rotation strategies generate lower RS than their 90°‐alternation counterparts. Due to the lack of reliable stress‐free references, the ND results are analyzed using von Mises stress. In general, ND results show significant RS spatial non‐uniformity. A comparison between ND and distortion results indicates that the RS component parallel to the building direction (Z‐axis) has a predominant role in the Z‐displacement. The use of a stress balance scheme allows to discuss the variability along the length of the specimens, as well as examine the absolute RS state.
- 30 March 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 23 (7)
Open AccessScanning Manufacturing Parameters Determining the Residual Stress State in LPBF IN718 Small Parts
The influence of scan strategy on the residual stress (RS) state of an as‐built IN718 alloy produced by means of laser powder bed fusion (LPBF) is investigated. Two scan vector rotations (90°‐alternation and 67°‐rotation), each produced following two different scan vector lengths (long and short), are used to manufacture four rectangular prisms. Neutron diffraction (ND) and laboratory X‐ray diffraction (XRD) techniques are used to map the bulk and surface RS state, respectively. The distortion induced upon removal from the baseplate is measured via profilometry. XRD measurements show that the two long scan vector strategies lead to higher RS when compared with the equivalent short scan vector strategies. Also, the 67°‐rotation strategies generate lower RS than their 90°‐alternation counterparts. Due to the lack of reliable stress‐free references, the ND results are analyzed using von Mises stress. In general, ND results show significant RS spatial non‐uniformity. A comparison between ND and distortion results indicates that the RS component parallel to the building direction (Z‐axis) has a predominant role in the Z‐displacement. The use of a stress balance scheme allows to discuss the variability along the length of the specimens, as well as examine the absolute RS state.
- Open Access
- 14 August 2020
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 53 (5) , 1181-1194
Neutron diffraction measurements of weld residual stresses in three-pass slot weld (Alloy 600/82) and assessment of the measurement uncertainty
This paper describes in detail two neutron diffraction residual stress measurements, performed on the ENGIN-X neutron scattering instrument at the ISIS facility in the UK and on the SALSA instrument at the Institut Laue–Langevin in Grenoble, France. The measurements were conducted as part of the NeT Task Group 6 (TG6) international measurement round robin on an Alloy 600/82 multi-pass weldment – a slot in an Alloy 600 plate filled with three Alloy 82 weld beads, simulating a repair weld. This alloy/weld combination is considered challenging to measure, due to the large grain size and texture in the weld, and large gradients in the stress-free lattice parameter between the parent and weld metal. The basic principles of the neutron diffraction technique are introduced and issues affecting the reliability of residual stress characterization are highlighted. Two different analysis strategies are used for estimation of residual stresses from the raw data. Chemical composition studies are used to measure the mixing of parent and weld metal and highlight the steep lattice parameter gradients that arise as a consequence. The inferred residual stresses are then compared with three sets of measurements performed on the same plate by other NeT partners on E3 at the HZB in Berlin, STRESS-SPEC at the FRM II in Munich and KOWARI in Sydney. A robust Bayesian estimation average is calculated from the combined five-instrument data set, allowing reliable best estimates of the residual stress distribution in the vicinity of the weldment. The systematic uncertainties associated with the residual stress measurements are determined separately in the weld and parent materials, and compared with those in the NeT TG4 benchmark. This is a three-pass slot-welded plate fabricated from American Iron and Steel Institute AISI 316L(N) austenitic stainless steel, and is normally considered less challenging to measure using diffraction techniques than all nickel welds. The uncertainties in the stress measurements by neutron diffraction for these two weldments seem to be comparable.
- 14 August 2020
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 53 (5) , 1181-1194
Open AccessNeutron diffraction measurements of weld residual stresses in three-pass slot weld (Alloy 600/82) and assessment of the measurement uncertainty
This paper describes in detail two neutron diffraction residual stress measurements, performed on the ENGIN-X neutron scattering instrument at the ISIS facility in the UK and on the SALSA instrument at the Institut Laue–Langevin in Grenoble, France. The measurements were conducted as part of the NeT Task Group 6 (TG6) international measurement round robin on an Alloy 600/82 multi-pass weldment – a slot in an Alloy 600 plate filled with three Alloy 82 weld beads, simulating a repair weld. This alloy/weld combination is considered challenging to measure, due to the large grain size and texture in the weld, and large gradients in the stress-free lattice parameter between the parent and weld metal. The basic principles of the neutron diffraction technique are introduced and issues affecting the reliability of residual stress characterization are highlighted. Two different analysis strategies are used for estimation of residual stresses from the raw data. Chemical composition studies are used to measure the mixing of parent and weld metal and highlight the steep lattice parameter gradients that arise as a consequence. The inferred residual stresses are then compared with three sets of measurements performed on the same plate by other NeT partners on E3 at the HZB in Berlin, STRESS-SPEC at the FRM II in Munich and KOWARI in Sydney. A robust Bayesian estimation average is calculated from the combined five-instrument data set, allowing reliable best estimates of the residual stress distribution in the vicinity of the weldment. The systematic uncertainties associated with the residual stress measurements are determined separately in the weld and parent materials, and compared with those in the NeT TG4 benchmark. This is a three-pass slot-welded plate fabricated from American Iron and Steel Institute AISI 316L(N) austenitic stainless steel, and is normally considered less challenging to measure using diffraction techniques than all nickel welds. The uncertainties in the stress measurements by neutron diffraction for these two weldments seem to be comparable.
- Open Access
- 30 July 2020
- Published by Cambridge University Press (CUP) in Microscopy and Microanalysis
- Vol. 26 (S2) , 3082-3085
Grain Growth, Porosity, and Hardness Changes in Sintered and Annealed Binder-jet 3D Printed Ni-Mn-Ga Magnetic Shape Memory Alloys
- 30 July 2020
- Published by Cambridge University Press (CUP) in Microscopy and Microanalysis
- Vol. 26 (S2) , 3082-3085
Open AccessGrain Growth, Porosity, and Hardness Changes in Sintered and Annealed Binder-jet 3D Printed Ni-Mn-Ga Magnetic Shape Memory Alloys
- Open Access
Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds
Plates (37 mm thick) of 6005A-T6 aluminum alloy were butt joined by a single-sided and double-sided friction stir welding (FSW). The 3D residual stresses in the joints were determined using neutron diffraction. The microstructures were characterized by a transmission electron microscope (TEM) and electron backscatter diffraction (EBSD). In the single-sided FSW specimen, there were acceptable mechanical properties with a tensile strength of 74.4% of base metal (BM) and low residual stresses with peak magnitudes of approximately 37.5% yield strength of BM were achieved. The hardness is related to the grain size of the nugget zone (NZ), and in this study, precipitations were dissolved due to the high heat input. In the double-sided FSW specimen, there were good mechanical properties with a tensile strength of 80.8% of BM, but high residual stresses with peak magnitudes of approximately 70% yield strength of BM were obtained. The heat input by the second pass provided an aging environment for the first-pass weld zone where the dissolved phases were precipitated and residual stresses were relaxed.
Open AccessResidual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds
Plates (37 mm thick) of 6005A-T6 aluminum alloy were butt joined by a single-sided and double-sided friction stir welding (FSW). The 3D residual stresses in the joints were determined using neutron diffraction. The microstructures were characterized by a transmission electron microscope (TEM) and electron backscatter diffraction (EBSD). In the single-sided FSW specimen, there were acceptable mechanical properties with a tensile strength of 74.4% of base metal (BM) and low residual stresses with peak magnitudes of approximately 37.5% yield strength of BM were achieved. The hardness is related to the grain size of the nugget zone (NZ), and in this study, precipitations were dissolved due to the high heat input. In the double-sided FSW specimen, there were good mechanical properties with a tensile strength of 80.8% of BM, but high residual stresses with peak magnitudes of approximately 70% yield strength of BM were obtained. The heat input by the second pass provided an aging environment for the first-pass weld zone where the dissolved phases were precipitated and residual stresses were relaxed.