Zengzhen Qian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zengzhen Qian has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Xian-Long Lu
China Electric Power Research Institute
6 shared publications - Bing Yue
School of Engineering and Technology, China University of Geosciences (Beijing), Beijing 100083, China
4 shared publications - Zilu Xie
School of Engineering and Technology, China University of Geosciences, No. 29 Xueyuan Road, Haidian District, Beijing 100083, China
3 shared publications - Hao Wang
School of Engineering and Technology, China University of Geosciences, No. 29 Xueyuan Road, Haidian District, Beijing 100083, China
2 shared publications Wen-Zhi Yang
Senior Civil Engineer, China Electric Power Research Institute, Beijing, PR China
2 shared publications- Hao Huang
State Grid Chongqing Electric Power Company, Chongqing, China
1 shared publication
Latest Publications
- Open Access
Mechanical Properties of Aeolian Sand Synergistically Stabilized with Multi-Source Solid Wastes and Basalt Fiber: Experimental Investigation and Discrete Element Modeling
To improve the tensile capacity and reduce the post-peak brittleness of stabilized aeolian sand, a binder comprising steel slag, ground granulated blast-furnace slag, phosphorus slag, and calcium carbide residue was combined with basalt fibers. Axial splitting tests using a four-factor, five-level orthogonal design and three-dimensional discrete element simulations investigated tensile behavior and reinforcement mechanisms. Basalt fibers increased tensile strength by 6.58–131.82%, slowed post-peak strength degradation, and improved specimen integrity after failure. Factor influence decreased in the order of binder content, water content, fiber content, and fiber length. All four factors exhibited statistically significant main effects on tensile strength at the 0.05 level, with binder content having the greatest influence. The optimum combination within the investigated ranges was 3% water content, 18.05% binder content, 1.5% fiber content, and 12 mm fiber length, yielding a mean tensile strength of 0.195 MPa after 28 d of curing in verification tests. Simulations reproduced the experimental mechanical responses, with tensile cracks dominating both models. Through load sharing and crack bridging, fibers maintained tensile load-transfer paths near cracks and restricted relative particle displacement, delaying crack coalescence and overall failure. These findings clarify the mesoscopic reinforcement mechanisms and support aeolian sand improvement and industrial solid waste utilization.
Open AccessMechanical Properties of Aeolian Sand Synergistically Stabilized with Multi-Source Solid Wastes and Basalt Fiber: Experimental Investigation and Discrete Element Modeling
To improve the tensile capacity and reduce the post-peak brittleness of stabilized aeolian sand, a binder comprising steel slag, ground granulated blast-furnace slag, phosphorus slag, and calcium carbide residue was combined with basalt fibers. Axial splitting tests using a four-factor, five-level orthogonal design and three-dimensional discrete element simulations investigated tensile behavior and reinforcement mechanisms. Basalt fibers increased tensile strength by 6.58–131.82%, slowed post-peak strength degradation, and improved specimen integrity after failure. Factor influence decreased in the order of binder content, water content, fiber content, and fiber length. All four factors exhibited statistically significant main effects on tensile strength at the 0.05 level, with binder content having the greatest influence. The optimum combination within the investigated ranges was 3% water content, 18.05% binder content, 1.5% fiber content, and 12 mm fiber length, yielding a mean tensile strength of 0.195 MPa after 28 d of curing in verification tests. Simulations reproduced the experimental mechanical responses, with tensile cracks dominating both models. Through load sharing and crack bridging, fibers maintained tensile load-transfer paths near cracks and restricted relative particle displacement, delaying crack coalescence and overall failure. These findings clarify the mesoscopic reinforcement mechanisms and support aeolian sand improvement and industrial solid waste utilization.
- Open Access
Comparative Analysis of Chemical Activators and Expansive Agents for Aeolian Sand Stabilization Using Industrial Solid Waste-Based Geopolymers
Aeolian sand is the primary geological material for construction in desert regions, and its stabilization with industrial solid wastes-based geopolymer (ISWG) provides an eco-friendly treatment replacing cement. This study comparatively investigated the enhancement effects of chemical activators and expansive agents on compressive strength of aeolian sand stabilized by ISWG (ASIG). Three chemical activators—NaOH, Ca(OH)2, and CaCl2—along with two expansive agents—desulfurized gypsum and bentonite—were considered. Through X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, mercury intrusion porosimetry and pH values tests, the enhancement mechanisms of the additives on ASIG were elucidated. Results demonstrate that the expansive agent exhibits significantly superior strengthening effects on ASIG compared to the widely applied chemical activators. Chemical activators promoted ISWs dissolution and hydration product synthesis, thereby densifying the hydration product matrix but concurrently enlarged interparticle pores. Desulfurized gypsum incorporation induced morphological changes in ettringite, and excessive desulfurized gypsum generated substantial ettringite that disrupted gel matrix. In contrast, bentonite demonstrated superior pore-filling efficacy while densifying gel matrix through a compaction effect. These findings highlight bentonite superior compatibility with the unique microstructure of aeolian sand compared to conventional alkaline activators or expansive agents, and better effectiveness in enhancing the strength of ASIG.
Open AccessComparative Analysis of Chemical Activators and Expansive Agents for Aeolian Sand Stabilization Using Industrial Solid Waste-Based Geopolymers
Aeolian sand is the primary geological material for construction in desert regions, and its stabilization with industrial solid wastes-based geopolymer (ISWG) provides an eco-friendly treatment replacing cement. This study comparatively investigated the enhancement effects of chemical activators and expansive agents on compressive strength of aeolian sand stabilized by ISWG (ASIG). Three chemical activators—NaOH, Ca(OH)2, and CaCl2—along with two expansive agents—desulfurized gypsum and bentonite—were considered. Through X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, mercury intrusion porosimetry and pH values tests, the enhancement mechanisms of the additives on ASIG were elucidated. Results demonstrate that the expansive agent exhibits significantly superior strengthening effects on ASIG compared to the widely applied chemical activators. Chemical activators promoted ISWs dissolution and hydration product synthesis, thereby densifying the hydration product matrix but concurrently enlarged interparticle pores. Desulfurized gypsum incorporation induced morphological changes in ettringite, and excessive desulfurized gypsum generated substantial ettringite that disrupted gel matrix. In contrast, bentonite demonstrated superior pore-filling efficacy while densifying gel matrix through a compaction effect. These findings highlight bentonite superior compatibility with the unique microstructure of aeolian sand compared to conventional alkaline activators or expansive agents, and better effectiveness in enhancing the strength of ASIG.
- Open Access
- 16 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 29987
Numerical study on bearing performance of rock socketed pile anchored by inclined anchors under uplift and horizontal combined load
Rock-socketed pile anchored by inclined anchors (RPIA) is a novel pile-anchor composite foundation developed to address the challenges of transmission tower installations in mountainous areas. This study investigates the bearing performance of RPIA under uplift-horizontal combined load using a nonlinear numerical model validated through full-scale field tests. Parametric analyses were conducted to examine the effects of inclined anchor length, angle and diameter, as well as connection node depth, on RPIA performance. Analysis reveals that inclined anchors reconstruct the path of potential slip surfaces within soil and rock mass, thereby effectively expanding the participation range of geotechnical bodies. Parametric analysis demonstrates that ultimate load of RPIA decreases with increasing angle, but increases with larger length and diameter of inclined anchor. The trends are further modulated by the relative position of the connection node within the geotechnical body. Longer inclined anchors shift the failure mode of the RPIA from the pull-out of short pile to the yielding of longitudinal rebar, and are suitable for shallower connection nodes to improve horizontal resistance. While shorter inclined anchors require the increment in anchor diameter and depth of connection point. The results of this study provide guidance for the design and promotion of RPIA.
- 16 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 29987
Open AccessNumerical study on bearing performance of rock socketed pile anchored by inclined anchors under uplift and horizontal combined load
Rock-socketed pile anchored by inclined anchors (RPIA) is a novel pile-anchor composite foundation developed to address the challenges of transmission tower installations in mountainous areas. This study investigates the bearing performance of RPIA under uplift-horizontal combined load using a nonlinear numerical model validated through full-scale field tests. Parametric analyses were conducted to examine the effects of inclined anchor length, angle and diameter, as well as connection node depth, on RPIA performance. Analysis reveals that inclined anchors reconstruct the path of potential slip surfaces within soil and rock mass, thereby effectively expanding the participation range of geotechnical bodies. Parametric analysis demonstrates that ultimate load of RPIA decreases with increasing angle, but increases with larger length and diameter of inclined anchor. The trends are further modulated by the relative position of the connection node within the geotechnical body. Longer inclined anchors shift the failure mode of the RPIA from the pull-out of short pile to the yielding of longitudinal rebar, and are suitable for shallower connection nodes to improve horizontal resistance. While shorter inclined anchors require the increment in anchor diameter and depth of connection point. The results of this study provide guidance for the design and promotion of RPIA.
- Open Access
Optimal Design and Application of Universal Cementitious Material Prepared Using Full Industrial Solid Wastes
This study developed a full solid waste-based cementitious material (ISWs-CM) using steel slag (SS), ground granulated blast furnace slag (GGBFS), phosphorus slag (PS), carbide slag (CS), and desulfurized gypsum (DG) to completely replace cement. A two-layer optimization strategy, combining three chemical moduli and simplex lattice experiments, was employed to determine the proportion and to investigate the impact of proportions on the uniaxial compressive strength of mortar. As an application case, the ISWs-CM with the optimal proportion was employed to stabilize aeolian sand, and its effectiveness as a cement substitute and the underlying mechanisms were investigated. The results indicated that the ISW proportion that maximized the strength of the mortar was SS:GGBFS:PS:CS = 5:20:20:40. The strength of the mortar was enhanced when the proportion of GGBFS exhibiting the highest reactivity was increased and also increased initially and then decreased with an increase in CS when the dosage of GGBFS was fixed. The aeolian sand stabilized by ISW-CM exhibited higher strength than that stabilized with cement. The greater number and variety of hydration products resulted in denser connections and encapsulation of sand particles, which highlights the synergistic effect of ISWs and the potential of ISW-CM as a cement replacement across diverse applications including aeolian sand stabilization.
Open AccessOptimal Design and Application of Universal Cementitious Material Prepared Using Full Industrial Solid Wastes
This study developed a full solid waste-based cementitious material (ISWs-CM) using steel slag (SS), ground granulated blast furnace slag (GGBFS), phosphorus slag (PS), carbide slag (CS), and desulfurized gypsum (DG) to completely replace cement. A two-layer optimization strategy, combining three chemical moduli and simplex lattice experiments, was employed to determine the proportion and to investigate the impact of proportions on the uniaxial compressive strength of mortar. As an application case, the ISWs-CM with the optimal proportion was employed to stabilize aeolian sand, and its effectiveness as a cement substitute and the underlying mechanisms were investigated. The results indicated that the ISW proportion that maximized the strength of the mortar was SS:GGBFS:PS:CS = 5:20:20:40. The strength of the mortar was enhanced when the proportion of GGBFS exhibiting the highest reactivity was increased and also increased initially and then decreased with an increase in CS when the dosage of GGBFS was fixed. The aeolian sand stabilized by ISW-CM exhibited higher strength than that stabilized with cement. The greater number and variety of hydration products resulted in denser connections and encapsulation of sand particles, which highlights the synergistic effect of ISWs and the potential of ISW-CM as a cement replacement across diverse applications including aeolian sand stabilization.
- Open Access
- 1 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (7) , 3858
Synergistic Preparation and Mechanistic Investigation of Full Industrial Solid Waste-Based Cementitious Materials for Aeolian Sand Stabilization
Aeolian sand serves as the principal foundation material for construction in desert regions, yet its stabilization predominantly relies on cement, presenting critical carbon emission challenges. This study developed a cementitious material utilizing complementary industrial solid wastes (ISWs)—steel slag (SS), ground granulated blast-furnace slag (GGBFS), phosphorus slag (PS), and carbide slag (CS)—based on clinker three chemical moduli (TCM) and simplex lattice design, aiming to replace cement for aeolian sand stabilization. ISW dosage effects on stabilized sand strength and mechanical properties were investigated, with stabilization mechanisms studied via phase and microstructural analysis. Results demonstrated that GGBFS exerted the most significant positive influence on the strength of stabilized sand. The optimal proportion was determined as SS:GGBFS:PS:CS = 5:35:20:40, achieving strength comparable to cement-stabilized aeolian sand in the literature. The elastic modulus and ductility of stabilized sand exhibited linear positive and exponential negative correlation with uniaxial compressive strength. The hydration products of ISWs, including C(-A)-S-H gel and ettringite similar to clinker, effectively enhanced interparticle bonding strength and pore-filling capacity. ISW proportions governed the composition and distribution of hydration products, thereby modulating microstructural density and strength, ultimately dictating macroscopic performance variations. The conclusions provide an environmentally friendly solution for aeolian sand stabilization in desert regions.
- 1 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (7) , 3858
Open AccessSynergistic Preparation and Mechanistic Investigation of Full Industrial Solid Waste-Based Cementitious Materials for Aeolian Sand Stabilization
Aeolian sand serves as the principal foundation material for construction in desert regions, yet its stabilization predominantly relies on cement, presenting critical carbon emission challenges. This study developed a cementitious material utilizing complementary industrial solid wastes (ISWs)—steel slag (SS), ground granulated blast-furnace slag (GGBFS), phosphorus slag (PS), and carbide slag (CS)—based on clinker three chemical moduli (TCM) and simplex lattice design, aiming to replace cement for aeolian sand stabilization. ISW dosage effects on stabilized sand strength and mechanical properties were investigated, with stabilization mechanisms studied via phase and microstructural analysis. Results demonstrated that GGBFS exerted the most significant positive influence on the strength of stabilized sand. The optimal proportion was determined as SS:GGBFS:PS:CS = 5:35:20:40, achieving strength comparable to cement-stabilized aeolian sand in the literature. The elastic modulus and ductility of stabilized sand exhibited linear positive and exponential negative correlation with uniaxial compressive strength. The hydration products of ISWs, including C(-A)-S-H gel and ettringite similar to clinker, effectively enhanced interparticle bonding strength and pore-filling capacity. ISW proportions governed the composition and distribution of hydration products, thereby modulating microstructural density and strength, ultimately dictating macroscopic performance variations. The conclusions provide an environmentally friendly solution for aeolian sand stabilization in desert regions.
- Open Access
Numerical Simulation of Uplift Behavior of a Rock-Socketed Pier Anchored by Inclined Anchors in Rock Masses
The rock-socketed pier anchored by inclined anchors (RPIA) is a new type of foundation developed by combining a rock-socketed pier and inclined anchors. Current research on RPIA is relatively limited, and the impact of design parameters on its bearing performance remains unclear. To investigate the uplift-bearing performance of RPIA, a finite-element model that considers the nonlinear properties of materials and multidirectional interactions was developed and verified. Based on this model, numerical simulations were performed on twenty-five RPIA that were designed using the L25 orthogonal array proposed by the Taguchi method, and the uplift load–displacement curve for each RPIA was obtained. Based on the interpretation of the elastic limit, uplift resistance, initial stiffness, and the ductility index for each simulated RPIA, the sensitivity of each factor was examined by analyzing the signal-to-noise ratio and variance. The results indicated that rock strength and pier diameter were the main factors determining the uplift performance of the RPIAs, while the angle of inclined anchors is the most influential factor affecting the ductility of RPIA. The primary role of the inclined anchor is to reduce the extraction of the pier after failure of the side resistance between the pier and rock mass, thus significantly enhancing the ductility of the uplift-loaded RPIA. The addition of reinforcements around the connection joints of the pier and anchors may prevent concrete failure and to fully execute the role of inclined anchors.
Open AccessNumerical Simulation of Uplift Behavior of a Rock-Socketed Pier Anchored by Inclined Anchors in Rock Masses
The rock-socketed pier anchored by inclined anchors (RPIA) is a new type of foundation developed by combining a rock-socketed pier and inclined anchors. Current research on RPIA is relatively limited, and the impact of design parameters on its bearing performance remains unclear. To investigate the uplift-bearing performance of RPIA, a finite-element model that considers the nonlinear properties of materials and multidirectional interactions was developed and verified. Based on this model, numerical simulations were performed on twenty-five RPIA that were designed using the L25 orthogonal array proposed by the Taguchi method, and the uplift load–displacement curve for each RPIA was obtained. Based on the interpretation of the elastic limit, uplift resistance, initial stiffness, and the ductility index for each simulated RPIA, the sensitivity of each factor was examined by analyzing the signal-to-noise ratio and variance. The results indicated that rock strength and pier diameter were the main factors determining the uplift performance of the RPIAs, while the angle of inclined anchors is the most influential factor affecting the ductility of RPIA. The primary role of the inclined anchor is to reduce the extraction of the pier after failure of the side resistance between the pier and rock mass, thus significantly enhancing the ductility of the uplift-loaded RPIA. The addition of reinforcements around the connection joints of the pier and anchors may prevent concrete failure and to fully execute the role of inclined anchors.
- Open Access
Effects of Cement Dosage, Curing Time, and Water Dosage on the Strength of Cement-Stabilized Aeolian Sand Based on Macroscopic and Microscopic Tests
Aeolian sand is distributed worldwide, exhibiting poor grading, low cohesion, and loose structure. Infrastructure construction in desert areas sometimes requires stabilization of the sand, with cement as the primary curing agent. This study first employed orthogonal experiments to evaluate critical factors, e.g., curing time, cement dosage, and water dosage, affecting the unconfined compressive strength (UCS) of the aeolian sand stabilized with cement (ASC). Each of the aforementioned factors were set at five levels, namely curing time (7, 14, 28, 60, and 90 days), cement dosage (3%, 5%, 7%, 9%, and 11%), and water dosage (3%, 6%, 9%, 12%, and 15%), respectively. The water and cement dosages were percentages of the mass of the natural aeolian sand. The results indicated that the sensitivity of the influencing factors on the UCS of ASC was cement dosage, curing time, and water dosage in descending order. The UCS of ASC positively correlated with curing time and cement dosage, while it first increased and then decreased with the water dosage increase. The optimal conditions were 90 days’ curing time, 11% cement dosage, and 9% water dosage. The microscopic analyses of ASC using optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) revealed that hydration products enhanced strength by bonding loose particles and filling pores, thereby improving compaction. The quantity and compactness of hydration products in the aeolian–cement reaction system increased with the increases in cement dosage and curing time, and low water dosage inhibited the hydration reaction. This study can provide insights into the stabilization mechanism of aeolian sand, aiding infrastructure development in desert regions.
Open AccessEffects of Cement Dosage, Curing Time, and Water Dosage on the Strength of Cement-Stabilized Aeolian Sand Based on Macroscopic and Microscopic Tests
Aeolian sand is distributed worldwide, exhibiting poor grading, low cohesion, and loose structure. Infrastructure construction in desert areas sometimes requires stabilization of the sand, with cement as the primary curing agent. This study first employed orthogonal experiments to evaluate critical factors, e.g., curing time, cement dosage, and water dosage, affecting the unconfined compressive strength (UCS) of the aeolian sand stabilized with cement (ASC). Each of the aforementioned factors were set at five levels, namely curing time (7, 14, 28, 60, and 90 days), cement dosage (3%, 5%, 7%, 9%, and 11%), and water dosage (3%, 6%, 9%, 12%, and 15%), respectively. The water and cement dosages were percentages of the mass of the natural aeolian sand. The results indicated that the sensitivity of the influencing factors on the UCS of ASC was cement dosage, curing time, and water dosage in descending order. The UCS of ASC positively correlated with curing time and cement dosage, while it first increased and then decreased with the water dosage increase. The optimal conditions were 90 days’ curing time, 11% cement dosage, and 9% water dosage. The microscopic analyses of ASC using optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) revealed that hydration products enhanced strength by bonding loose particles and filling pores, thereby improving compaction. The quantity and compactness of hydration products in the aeolian–cement reaction system increased with the increases in cement dosage and curing time, and low water dosage inhibited the hydration reaction. This study can provide insights into the stabilization mechanism of aeolian sand, aiding infrastructure development in desert regions.
- Open Access
- 29 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3455
Influence of Five Additives on No Loading Swelling Potential of Red Clay
In this study, cement, zeolite powder and three industrial by-products (blast furnace slag, steel slag, and fly ash) were selected as additives to study their effects on the swelling potential of red clay with different curing ages and dosages. At the same time, the mechanism of additives reducing the swelling potential of red clay was analyzed by scanning electron microscope (SEM) and X-ray fluorescence (XRF) tests. The X-ray diffraction (XRD) test was used to detect the clay mineral content of the red clay specimens before and after the modification to determine the change in the clay mineral content of the specimens. The direct shear test was used to explore the influence of additives on the strength of red clay. The results show that with 9% cement content, the no loading swelling potential of specimens can be reduced by 82.5% under 28 days of curing, and the cohesion of the specimens can be greatly increased by 82%. However, the specimens with cement have an increase in no loading swelling potential under the condition of no curing. In contrast, when steel slag is used as an additive to modify the swelling properties of red clay, the swelling potential can be reduced without curing, but the addition of steel slag will reduce the cohesive strength of specimens. XRD testing shows that the clay mineral composition in cement-modified specimens and steel slag-modified specimens experienced a relative change, the relative content of montmorillonite and illite decreased, and the relative content of kaolinite increased. Combined with SEM and XRF test results, it is concluded that cement’s reduction in the swelling potential of red clay depends on pozzolanic reaction products filling the pores in specimens and bonding clay particles, so as to reduce the permeability of red clay and increase the resistance during swelling. The addition of cement can also convert hydrophilic clay minerals into nonhydrophilic clay minerals. Compared with cement, the reduction in swelling potential caused by steel slag mainly depends on the adsorption of ions to reduce the adsorption of water molecules on the surface of clay slices.
- 29 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3455
Open AccessInfluence of Five Additives on No Loading Swelling Potential of Red Clay
In this study, cement, zeolite powder and three industrial by-products (blast furnace slag, steel slag, and fly ash) were selected as additives to study their effects on the swelling potential of red clay with different curing ages and dosages. At the same time, the mechanism of additives reducing the swelling potential of red clay was analyzed by scanning electron microscope (SEM) and X-ray fluorescence (XRF) tests. The X-ray diffraction (XRD) test was used to detect the clay mineral content of the red clay specimens before and after the modification to determine the change in the clay mineral content of the specimens. The direct shear test was used to explore the influence of additives on the strength of red clay. The results show that with 9% cement content, the no loading swelling potential of specimens can be reduced by 82.5% under 28 days of curing, and the cohesion of the specimens can be greatly increased by 82%. However, the specimens with cement have an increase in no loading swelling potential under the condition of no curing. In contrast, when steel slag is used as an additive to modify the swelling properties of red clay, the swelling potential can be reduced without curing, but the addition of steel slag will reduce the cohesive strength of specimens. XRD testing shows that the clay mineral composition in cement-modified specimens and steel slag-modified specimens experienced a relative change, the relative content of montmorillonite and illite decreased, and the relative content of kaolinite increased. Combined with SEM and XRF test results, it is concluded that cement’s reduction in the swelling potential of red clay depends on pozzolanic reaction products filling the pores in specimens and bonding clay particles, so as to reduce the permeability of red clay and increase the resistance during swelling. The addition of cement can also convert hydrophilic clay minerals into nonhydrophilic clay minerals. Compared with cement, the reduction in swelling potential caused by steel slag mainly depends on the adsorption of ions to reduce the adsorption of water molecules on the surface of clay slices.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Compression Load Tests on Composite Foundations of Spread Footing Anchored by Helical Anchors
This study elucidates the compression behavior of a type of composite foundation of spread footing anchored by helical anchors. Three composite foundations were installed at a field site, and compression load testing was carried out on each foundation. Both the site conditions and the load tests were documented comprehensively. The compression load‐settlement curves of composite foundations exhibit an initial linear‐elastic segment, a curve transition, and a final linear region, and their capacities should be interpreted from the load‐settlement curves. Five representative interpretation criteria (Chin, Terzaghi and Peck, slope tangent, tangent intersection, and L1–L2) were employed to determine the capacity of each foundation. Both the helical anchors and the footing share compression loadings on the composite foundation. Soil pressure cells at the center, near the edge, and at the corner of the footing represent a distribution from the lower, middle, and higher ranges of incremental soil pressures underneath the footing. Helical anchors underneath the footing approximately share 60%–80% of total load applied on the composite foundation pier, and higher compression resistance of a composite foundation can be obtained by increasing the footing embedment depth and the number of helical anchors underneath the footing.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessCompression Load Tests on Composite Foundations of Spread Footing Anchored by Helical Anchors
This study elucidates the compression behavior of a type of composite foundation of spread footing anchored by helical anchors. Three composite foundations were installed at a field site, and compression load testing was carried out on each foundation. Both the site conditions and the load tests were documented comprehensively. The compression load‐settlement curves of composite foundations exhibit an initial linear‐elastic segment, a curve transition, and a final linear region, and their capacities should be interpreted from the load‐settlement curves. Five representative interpretation criteria (Chin, Terzaghi and Peck, slope tangent, tangent intersection, and L1–L2) were employed to determine the capacity of each foundation. Both the helical anchors and the footing share compression loadings on the composite foundation. Soil pressure cells at the center, near the edge, and at the corner of the footing represent a distribution from the lower, middle, and higher ranges of incremental soil pressures underneath the footing. Helical anchors underneath the footing approximately share 60%–80% of total load applied on the composite foundation pier, and higher compression resistance of a composite foundation can be obtained by increasing the footing embedment depth and the number of helical anchors underneath the footing.
- 1 February 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 173 (1) , 70-80
Comparative lateral load field tests on straight-sided and belled piers in sloped ground
Comparative lateral load field tests were conducted on two straight-sided and two belled piers in a natural arid loess sloping ground with an inclination angle of 20° in the western Chinese Loess Plateau. The pier-head displacements, sloping ground surface deformations and soil pressure distributions were measured. The lateral load–displacement curves of the straight-sided and belled piers in the sloping ground generally exhibited the same three-phase non-linear behaviour, and their performances were similar to those of laterally loaded drilled shafts in horizontal ground. The ‘interpreted failure load’ of the laterally loaded piers in sloping ground was obtained using the representative lateral interpretation criteria and their extensions. Compared with the normalised lateral load–displacement curves of the drilled shafts in horizontal ground under drained and undrained lateral loadings, the displacement required to completely mobilise the lateral resistance for piers in sloping ground was much smaller. It was found that the use of belling can cause greater load transfer depths and can effectively mobilise more soil to resist lateral load. In addition, for both straight-sided and belled piers, an additional embedment of the shaft in sloping ground can increase lateral resistance to match the level-ground lateral capacity.
- 1 February 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 173 (1) , 70-80
Comparative lateral load field tests on straight-sided and belled piers in sloped ground
Comparative lateral load field tests were conducted on two straight-sided and two belled piers in a natural arid loess sloping ground with an inclination angle of 20° in the western Chinese Loess Plateau. The pier-head displacements, sloping ground surface deformations and soil pressure distributions were measured. The lateral load–displacement curves of the straight-sided and belled piers in the sloping ground generally exhibited the same three-phase non-linear behaviour, and their performances were similar to those of laterally loaded drilled shafts in horizontal ground. The ‘interpreted failure load’ of the laterally loaded piers in sloping ground was obtained using the representative lateral interpretation criteria and their extensions. Compared with the normalised lateral load–displacement curves of the drilled shafts in horizontal ground under drained and undrained lateral loadings, the displacement required to completely mobilise the lateral resistance for piers in sloping ground was much smaller. It was found that the use of belling can cause greater load transfer depths and can effectively mobilise more soil to resist lateral load. In addition, for both straight-sided and belled piers, an additional embedment of the shaft in sloping ground can increase lateral resistance to match the level-ground lateral capacity.