Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hua-Pin Chen has a total of 34 co-authors. Here are the top co-authors by number of shared publications:

  • San-Fu Wang

    National Chin-Yi University of Technology College of Electrical Engineering and Computer Science Taichung and Department of Electronic Engineering, National Chin-Yi University of Technology, Taichung, Taiwan

    12 shared publications
  • Yitsen Ku

    Department of Electrical and Computer Engineering, California State University at Fullerton, Fullerton, CA, USA

    12 shared publications
  • San-Fu Wang

    8 shared publications
  • Yu-Hsi Chen

    Department of Electrical Engineering, National Formosa University, Yunlin, Huwei, Taiwan

    4 shared publications
  • Liang-Yen Chen

    Department of Electrical Engineering, Chang Gung University, Taoyuan, Taiwan

    2 shared publications
  • Yitsen Ku

    Department of Electrical Engineering, California State University Fullerton, Fullerton, CA, USA

    2 shared publications

Latest Publications

  • Open Access

    Chip Implementation of Two New VCII-Based Voltage/Transimpedance-Mode KHN-Equivalent Biquads

    by Hua-Pin Chen, San-Fu Wang, Ming- Jin- Yu, Liang-Yen Chen, Yu-Hsi Chen

    This paper presents two new VCII-based Kerwin-Huelsman-Newcomb (KHN) equivalent biquad circuits, each comprising three second-generation voltage conveyors (VCIIs), two grounded capacitors, and five resistors. Either voltage mode (VM) or trans-impedance mode (TIM) can operate in each proposed circuit configuration. Transfer function analysis using a VM inverting bandpass (IBP) filter yields two additional non-inverting/inverting KHN biquad transfer functions for the two proposed VM/TIM KHN-equivalent biquads. The first proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, a non-inverting low-pass (NLP) filter, and an inverting high-pass (IHP) filter. In contrast, the second proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, an inverting low-pass (ILP) filter, and a non-inverting high-pass (NHP) filter. Each proposed VM/TIM KHN-equivalent biquad features three low-impedance voltage outputs in the designed circuit, eliminating the need for additional voltage buffers (VBs) in the circuit measurements. The two proposed KHN-equivalent biquads are integrated into a single chip, occupying a total area of 1.44 mm2. This technology uses the TSMC 0.18 μm 1P6M CMOS process, with the chip operating at a supply voltage of ±0.9 V. The measured power dissipation of the first KHN-equivalent biquad is 2.7 mW, while the measured power dissipation of the second one is 3.24 mW. The measured spurious-free dynamic range (SFDR) of the first KHN-equivalent biquad is 41.18 dBc, while the measured SFDR of the second one is 40.94 dBc. With an input voltage of 1.2 Vpp, the measured total harmonic distortion (THD) values for both KHN-equivalent biquads are below 1 %. The proposed two KHN-equivalent biquads have the advantages of high density, system integration, efficiency, low cost, low power consumption, and effective utilization of chip layout area. Simulations and on-chip measurements are carried out for both KHN-equivalent biquads to validate the theoretical design and demonstrate their on-chip feasibility.


  • Open Access

    All-Pass Filter IC Design and Its Cascaded Second-Order and Third-Order All-Pass Filters and Quadrature Sinusoidal Oscillator Applications

    by Hua-Pin Chen, San-Fu Wang, Yitsen Ku, Liang-Yen Chen, Tzu-Yi Liu

    This study presents the design and application of a cascaded voltage-mode (VM) first-order all-pass filter (APF) integrated circuit (IC) based on a positive differential current conveyor (DDCC+). The proposed single- and differential-input VM-APF uses two DDCC+ active components and two passive components consisting of a grounded capacitor and a resistor. Both non-inverting APF (NAPF) and inverting APF (IAPF) transfer functions of VM-APF can be implemented without any critical passive component matching condition. The proposed first-order VM-APF can realize both NAPF and IAPF transfer functions with high-input and low-output (HILO) impedance, which makes it suitable for cascading without any voltage buffer. Owing to the VM-APF with HILO impedance configuration, the proposed circuit can quickly cascade nth-order VM-APF without adding additional circuit architectures. The circuit is implemented on-chip based on TSMC 1P6M 180 nm process technology with a supply voltage of ±0.9 V. The first-order VM-APF power consumption is 1.8 mW. Integrating a first-order VM-APF into a single chip can improve system integration efficiency, reduce voltage and power consumption, and shrink circuit size. On-chip measurements verify the cascading feasibility of the proposed first-order VM-APF and demonstrate that the implemented chip can be easily cascaded for second- and third-order VM-APFs and VM APF-based quadrature sinusoidal oscillator applications.


  • Open Access

    Design and Verification of a New Universal Active Filter Based on the Current Feedback Operational Amplifier and Commercial AD844 Integrated Circuit

    by Hua-Pin Chen, I-Chyn Wey, Liang-Yen Chen, Cheng-Yueh Wu, San-Fu Wang

    This paper presents a triple-input and four-output type voltage-mode universal active filter based on three current-feedback operational amplifiers (CFOAs). The filter employs three CFOAs, two grounded capacitors, and six resistors. The filter structure has three high-input and three low-output impedances that simultaneously provide band-reject, high-pass, low-pass, and band-pass filtering functions with single-input and four-output type and also implements an all-pass filtering function by connecting three input signals to one input without the use of voltage inverters or switches. The same circuit configuration enables two unique filtering functions: low-pass notch and high-pass notch. Three CFOAs with three high-input and low-output impedance terminals enable cascading without voltage buffers. The circuit is implemented using three commercial off-the-shelf AD844 integrated circuits, two grounded capacitors, and six resistors and further implemented as a CFOA-based chip using three CFOAs, two grounded capacitors, and six resistors. The CFOA-based chip has lower power consumption and higher integration than the AD844-based filter. The circuit was simulated using OrCAD PSpice to verify the AD844-based filter and Synopsys HSpice for post-layout simulation of the CFOA-based chip. The theoretical analysis is validated and confirmed by measurements on an AD844-based filter and a CFOA-based chip.


  • Open Access

    Two New and Improved Electronically Adjustable Voltage-Mode Multifunction Biquadratic Filters With Independent Control of Band-Pass, High-Pass, and Low-Pass/Regular Notch Filter Gains

    by Hua-Pin Chen, San-Fu Wang, Chih-Yang Chang, Shih-Jun Chen, Yu-Hsi Chen

    In this study, two new and improved electronically adjustable voltage-mode (VM) biquadratic filters using three off-the-shelf LT1228 integrated circuits (ICs), two grounded capacitors (GCs), and six resistors are proposed for independent control of the band-pass (BP), high-pass (HP), and low-pass/regular notch (LPN/RN) filter gains. Each proposed electronically adjustable VM multifunction biquadratic filter has one input and six output voltages, enabling simultaneous realization of one low-pass (LP), two BP, two HP, and one LPN/RN filtering responses from the same configuration. Each filter parameter, namely the pole angular frequency ( $\omega _{o}$ ) and quality factor ( $Q$ ), can be electronically controlled and orthogonally adjusted by the corresponding LT1228 bias current $I_{B}$ . In special cases, the parameters of $\omega _{o}$ and $Q$ can be electronically controlled and independently adjusted. Each electronically adjustable VM multifunction biquadratic filter has one high input impedance and three low output impedances for independent control of BP, HP, and LPN/RN filter gains. Due to its one high input impedance and three low output impedances, each proposed filter is suitable for cascaded VM circuits without external voltage buffers. Pspice simulations are used to verify the theoretical structure analysis of each proposed LT1228-based electronically adjustable VM multifunction biquadratic filter. Furthermore, experimental tests are performed using three off-the-shelf LT1228 ICs, and several passive components to verify and evaluate the performance of each proposed LT1228-based biquadratic filter.


  • Experimental Verification of On-Chip Biquadratic Filter and Oscillator

    by Hua-Pin Chen, San-Fu Wang, Yitsen Ku, Yuan-Cheng Yi, Yu-Hsi Chen

    This paper presents an improved gain-independent tunable voltage-mode (VM) multifunction biquadratic filter (MBF) based on the current-feedback amplifier (CFA), which is easily modification as a quadrature oscillator (QO). Each of the proposed VM-MBF and VM-QO configurations is implemented on a chip employing Taiwan Semiconductor Manufacturing Company (TSMC) 0.18 μm process with three CFAs, two grounded capacitors and five resistors. The proposed VM-MBF and VM-QO configurations are both implemented on integrated circuits (ICs) with chip areas of 0.24 mm 2 and 0.23 mm 2 (without PADs), respectively. Based on a ±0.9 V voltage supply and a rail-to-rail input voltage range of 0.05 V pp ≤ Vin ≤ 1.5 V pp , the VM-MBF chip has a maximum efficiency of 83.33%. For linear evaluation of the VM-MBF chip, the measured input 1-dB compression point (P1dB) is about 8.1 dBm. For nonlinear evaluation of the two-tone test, the measured third-order intercept point (TOI) and third-order intermodulation distortion (IMD3) are about 27.26 dBm and –67.5 dBc, respectively. The measured phase noise (PN) of the VM-MBF chip is –101.06 dBc/Hz at 1 kHz offset. With high-input (HI) and low-output (LO) impedances, the proposed VM-MBF can simultaneously achieve inverting low-pass (ILP), inverting band-pass (IBP) and non-inverting band-stop (NBS) responses with gain-independent controllability. It can be easily modified into a VM-QO with fully decoupled control of both the frequency of oscillation (FO) and condition of oscillation (CO). The simulation and measurement results in the time and frequency domains confirm the theories of the proposed VM-MBF and VM-QO configurations.


  • Open Access

    Synthesis of High-Input Impedance Electronically Tunable Voltage-Mode Second-Order Low-Pass, Band-Pass, and High-Pass Filters Based on LT1228 Integrated Circuits

    by Hua-Pin Chen, Shih-Jun Chen, Chih-Yang Chang

    This paper introduces two new high-input impedance electronically tunable voltage-mode (VM) multifunction second-order architectures with band-pass (BP), low-pass (LP), and high-pass (HP) filters. Both proposed architectures have one input and five outputs, implemented employing three commercial LT1228 integrated circuits (ICs), two grounded capacitors, and five resistors. Both proposed architectures also feature one high-impedance input port and three low-impedance output ports for easy connection to other VM configurations without the need for VM buffers. The two proposed VM LT1228-based second-order multifunction filters simultaneously provide BP, LP, and HP filter transfer functions at Vo1, Vo2, and Vo3 output terminals. The pole angular frequencies and the quality factors of the two proposed VM LT1228-based second-order multifunction filters can be electronically and orthogonally adjusted by the bias currents from their corresponding commercial LT1228 ICs, and can be independently adjusted in special cases. In addition, both proposed VM LT1228-based second-order multifunction filters have two independent gain-controlled BP and LP filter transfer functions at Vo4 and Vo5 output terminals, respectively. Based on the three commercial LT1228 ICs and several passive components, simulations and experimental measurements are provided to verify the theoretical predictions and demonstrate the performance of the two proposed high-input impedance electronically tunable VM LT1228-based second-order multifunction filters. The measured input 1-dB power gain compression point (P1dB), third-order IMD (IMD3), third-order intercept (TOI) point, and spurious-free dynamic range (SFDR) of the first proposed filter were −7.1 dBm, −48.84 dBc, 4.133 dBm, and 45.02 dBc, respectively. The measured input P1dB, IMD3, TOI, and SFDR of the second proposed filter were −7 dBm, −49.65 dBc, 4.316 dBm, and 45.88 dBc, respectively. Both proposed filters use a topology synthesis method based on the VM second-order non-inverting/inverting HP filter transfer functions to generate the BP, LP and HP filter transfer functions simultaneously, making them suitable for applications in three-way crossover networks.


  • Open Access

    A novel voltage-mode universal second-order filter using five single ended OTAs and its quadrature sinusoidal oscillator application

    by San-Fu Wang, Hua-Pin Chen, Yitsen Ku, Yi-Chun Lin

    This study proposes a single-ended operational trans-conductance amplifier (SEOTA)-based triple inputs and single output high-input impedance voltage-mode (VM) universal second-order filter. The proposed universal VM SEOTA-based second-order filter can be realized for the non-inverting low-pass, non-inverting high-pass, non-inverting band-reject, non-inverting all-pass and inverting band-pass filtering functions by appropriately using different triple-input voltage signals. The high-input impedances of the proposed universal VM SEOTA-based configuration enable the second-order filter to be cascaded without additional buffers. The proposed configuration does not employ external resistors and accordingly is an active SEOTAs and capacitors (SEOTA-C) universal second-order filter. The proposed circuit using two grounded capacitors which is more apposite to further develop into an integrated circuit implementation. The resonance angular frequency and quality factor are orthogonal electronically adjustable. By slightly modifying the proposed universal VM SEOTA-based second-order filter configuration, the VM SEOTA-C quadrature sinusoidal oscillator is achieved. The oscillation frequency and the oscillation condition of the quadrature sinusoidal oscillator can be independently and electronically tuned by adjusting the bias currents of two SEOTAs. PSpice simulation results confirmed theoretic anticipation. The result of the experiment of the commercially available SEOTAs, LT1228s, are also used to verify the characteristics of the proposed universal VM SEOTA-based second-order filter and VM SEOTA-based quadrature sinusoidal oscillator.


  • Open Access

    Four Unity/Variable Gain First-Order Cascaded Voltage-Mode All-Pass Filters and Their Fully Uncoupled Quadrature Sinusoidal Oscillator Applications

    by Hua-Pin Chen, San-Fu Wang, Yitsen Ku, Yuan-Cheng Yi, Yi-Fang Li, Yu-Hsi Chen

    This paper presents four new designs for a first-order voltage-mode (VM) all-pass filter (APF) circuit based on two single-output positive differential voltage current conveyors (DVCCs). The first two proposed VMAPFs with unity-gain, high-input (HI) impedance and low-output (LO) impedance use two DVCCs, a grounded capacitor, and a grounded resistor. The last two proposed first-order VMAPFs with HI impedance and variable-gain control are two resistors added to each of the first two VMAPFs. The last two proposed first-order VMAPFs with variable-gain control use two DVCCs, one grounded capacitor, and three grounded resistors and provide HI impedances, so that VMAPFs can be directly cascaded to obtain high-order filters without additional voltage buffers. The four implementation circuits based only on grounded passive components are particularly applicable for integrated circuits (ICs). To confirm the cascading characteristics, an application example of a fully-uncoupled quadrature sinusoidal oscillator (FQSO) is also proposed. PSpice simulation results have confirmed the feasibility of the proposed structures. VMAPF and FQSO circuits are also constructed from commercial AD8130 and AD844 ICs, and their experimentally measured time and frequency responses are compared to theoretical values. The supply voltages for both the AD8130 and AD844 ICs were ±5 V. The measured power dissipation of the proposed first-order VMAPF and second-order FQSO circuits is 0.6 W. The measured input 1-dB compression point for the four VMAPFs is about 19 dB. The measured total harmonic distortion of the four VMAPFs is less than 0.67% when the input voltage reaches 2.5 Vpp. The calculated figures of merit for the four VMAPFs are 628.2 × 103, 603.06 × 103, 516.53 × 103, and 496.42 × 103, respectively.


  • Open Access

    Design of Second-Order Multifunction Filter IC Based on Current Feedback Amplifiers With Independent Voltage Gain Control

    by Hua-Pin Chen, San-Fu Wang, Yitsen Ku, An-Chun Yeh, Yu-Hsi Chen

    This paper presents the integrated circuit (IC) design and implementation of the voltage-mode (VM) second-order gain-controlled multifunction filter (GMF), which consists of three current feedback amplifiers (CFAs), two grounded capacitors and four resistors. The design and implementation of the chip are based on a $0.18~\mu \text{m}$ process technology, and offers the attractive advantages of high efficiency, high reliability, low voltage, low power consumption, small size and good performance. The VM-GMF chip implements low-pass (LP), inverting band-pass (IBP) and band-stop (BS) filtering functions, and can independently control the gain of LP, IBP and BS filtering functions. The chip operates with a wide input voltage of 1.2 $\text{V}_{\mathrm {pp}}$ at ±0.9 V supply voltage, and has a figure-of-merit (FOM) of 66.7%. The on-chip measured input power at 1-dB compression point (IP1dB) is about 7.5 dBm with good linearity and the measured power dissipation (PD) is 5.4 mW with low voltage and low power consumption. The measured phase noise (PN) at an offset frequency of 1 kHz is −100.61 dBc/Hz. The measured value of the third-order intermodulation distortion (IMD3) is −57.38 dBc and the third-order intercept point (TOI) is 21.77 dBm. Simulations and on-chip experimental measurements demonstrate the theoretical analysis of the proposed VM-GMF.