San-Fu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
San-Fu Wang has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Hua-Pin Chen
Department of Electronic Engineering, Ming Chi University of Technology, Taishan, New Taipei, Taiwan
12 shared publications - Yitsen Ku
Department of Electrical and Computer Engineering, California State University at Fullerton, Fullerton, CA, USA
10 shared publications - Hsiao-Hsing Chou
Department of Computer Science and Information Engineering, National Taichung University of Science and Technology, Taichung, Taiwan
4 shared publications - Yang-Hsin Fan
Department of Computer Science and Information Engineering, National Taitung University, Taitung 95092, Taiwan
3 shared publications - Hsin-Liang Chen
Department of Electrical and Computer Engineering, Tamkang University, 151, Yingzhuan Rd., Tamsui Dist., New Taipei City 251301, Taiwan
2 shared publications Hua-Pin Chen
Department of Electronic Engineering, Ming Chi University of Technology, Taishan, New Taipei City, Taiwan, R.O.C
2 shared publications
Latest Publications
- 14 October 2026
- Published by Emerald Publishing in Microelectronics International
- p. 1-11
A wide-input 7–40 V low-dropout regulator and bandgap-referenced precision output
Purpose: This paper aims to present a robust wide-input low-dropout regulator (LDO) for automotive and industrial power-management applications. The proposed LDO operates across a wide input voltage range from 7 to 40 V, delivering a regulated 5 V output for low-current analog and mixed-signal subsystems. The main design objectives are to improve high-voltage tolerance, startup reliability and reference stability under harsh supply and temperature conditions. Design/methodology/approach: The proposed architecture combines a hybrid high-voltage/low-voltage (HV/LV) MOS isolation strategy with a digitally supervised startup and reference-handover mechanism. High-voltage MOS devices are selectively used at input-stressed nodes to isolate excessive voltage stress, while most analog control and reference circuits are implemented with low-voltage devices to improve transconductance and design efficiency. During startup, a constant-gm bias circuit provides a temporary reference to initiate regulation. Once the output voltage reaches a stable operating level, a comparator and a 4-bit digital counter control the handover from the constant-gm reference to the bandgap reference. An on-chip 550 kHz clock generator is integrated to support the digital counter without requiring external timing signals. Findings: The proposed LDO was implemented using a 0.25-µm 1P3M CMOS process and verified through circuit-level SPICE simulations. The regulator achieves stable operation across a 7 to 40 V input-voltage range, delivers a regulated 5 V output and supports a maximum load current of 25 µA. The bandgap reference provides an approximately 1.2 V reference voltage for steady-state operation. Full process−voltage−temperature simulations were performed across TT, SS, FF, SF and FS process corners, an input-voltage range of 7 to 40 V and a temperature range from −40°C to 125°C. In addition, 200-run Monte Carlo simulations were conducted to evaluate the effects of device mismatch on reference voltage, output voltage and startup transition timing. The results confirm stable regulation, deterministic startup behavior and successful prevention of zero-current equilibrium under slow input-ramp conditions. Key simulated performance metrics: They include a dropout voltage of 1.0 V at a 25 µA load, line regulation of ±0.2% over the 7–40 V input range, load regulation of ±0.5% across the 0–25 µA load range and a temperature coefficient of 200 ppm/°C from −40°C to 125°C. Originality/value: The main contribution of this work is not limited to extending the input-voltage range of an LDO, but lies in the system-level integration of high-voltage isolation, low-voltage control circuitry and digitally supervised reference handover. Compared with conventional wide-input LDO designs that mainly emphasize regulation accuracy or transient response, the proposed design explicitly addresses startup determinism and high-voltage domain isolation in a self-powered architecture. The hybrid HV/LV MOS strategy improves practical implementation efficiency, while the digitally supervised startup mechanism ensures reliable activation before the bandgap reference takes over. These features make the proposed LDO suitable for low-current automotive and industrial power-management systems requiring wide-input tolerance, stable startup and robust operation under process, voltage and temperature variations.
- 14 October 2026
- Published by Emerald Publishing in Microelectronics International
- p. 1-11
A wide-input 7–40 V low-dropout regulator and bandgap-referenced precision output
Purpose: This paper aims to present a robust wide-input low-dropout regulator (LDO) for automotive and industrial power-management applications. The proposed LDO operates across a wide input voltage range from 7 to 40 V, delivering a regulated 5 V output for low-current analog and mixed-signal subsystems. The main design objectives are to improve high-voltage tolerance, startup reliability and reference stability under harsh supply and temperature conditions. Design/methodology/approach: The proposed architecture combines a hybrid high-voltage/low-voltage (HV/LV) MOS isolation strategy with a digitally supervised startup and reference-handover mechanism. High-voltage MOS devices are selectively used at input-stressed nodes to isolate excessive voltage stress, while most analog control and reference circuits are implemented with low-voltage devices to improve transconductance and design efficiency. During startup, a constant-gm bias circuit provides a temporary reference to initiate regulation. Once the output voltage reaches a stable operating level, a comparator and a 4-bit digital counter control the handover from the constant-gm reference to the bandgap reference. An on-chip 550 kHz clock generator is integrated to support the digital counter without requiring external timing signals. Findings: The proposed LDO was implemented using a 0.25-µm 1P3M CMOS process and verified through circuit-level SPICE simulations. The regulator achieves stable operation across a 7 to 40 V input-voltage range, delivers a regulated 5 V output and supports a maximum load current of 25 µA. The bandgap reference provides an approximately 1.2 V reference voltage for steady-state operation. Full process−voltage−temperature simulations were performed across TT, SS, FF, SF and FS process corners, an input-voltage range of 7 to 40 V and a temperature range from −40°C to 125°C. In addition, 200-run Monte Carlo simulations were conducted to evaluate the effects of device mismatch on reference voltage, output voltage and startup transition timing. The results confirm stable regulation, deterministic startup behavior and successful prevention of zero-current equilibrium under slow input-ramp conditions. Key simulated performance metrics: They include a dropout voltage of 1.0 V at a 25 µA load, line regulation of ±0.2% over the 7–40 V input range, load regulation of ±0.5% across the 0–25 µA load range and a temperature coefficient of 200 ppm/°C from −40°C to 125°C. Originality/value: The main contribution of this work is not limited to extending the input-voltage range of an LDO, but lies in the system-level integration of high-voltage isolation, low-voltage control circuitry and digitally supervised reference handover. Compared with conventional wide-input LDO designs that mainly emphasize regulation accuracy or transient response, the proposed design explicitly addresses startup determinism and high-voltage domain isolation in a self-powered architecture. The hybrid HV/LV MOS strategy improves practical implementation efficiency, while the digitally supervised startup mechanism ensures reliable activation before the bandgap reference takes over. These features make the proposed LDO suitable for low-current automotive and industrial power-management systems requiring wide-input tolerance, stable startup and robust operation under process, voltage and temperature variations.
- Open Access
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 73056-73075
Chip Implementation of Two New VCII-Based Voltage/Transimpedance-Mode KHN-Equivalent Biquads
This paper presents two new VCII-based Kerwin-Huelsman-Newcomb (KHN) equivalent biquad circuits, each comprising three second-generation voltage conveyors (VCIIs), two grounded capacitors, and five resistors. Either voltage mode (VM) or trans-impedance mode (TIM) can operate in each proposed circuit configuration. Transfer function analysis using a VM inverting bandpass (IBP) filter yields two additional non-inverting/inverting KHN biquad transfer functions for the two proposed VM/TIM KHN-equivalent biquads. The first proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, a non-inverting low-pass (NLP) filter, and an inverting high-pass (IHP) filter. In contrast, the second proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, an inverting low-pass (ILP) filter, and a non-inverting high-pass (NHP) filter. Each proposed VM/TIM KHN-equivalent biquad features three low-impedance voltage outputs in the designed circuit, eliminating the need for additional voltage buffers (VBs) in the circuit measurements. The two proposed KHN-equivalent biquads are integrated into a single chip, occupying a total area of 1.44 mm2. This technology uses the TSMC 0.18 μm 1P6M CMOS process, with the chip operating at a supply voltage of ±0.9 V. The measured power dissipation of the first KHN-equivalent biquad is 2.7 mW, while the measured power dissipation of the second one is 3.24 mW. The measured spurious-free dynamic range (SFDR) of the first KHN-equivalent biquad is 41.18 dBc, while the measured SFDR of the second one is 40.94 dBc. With an input voltage of 1.2 Vpp, the measured total harmonic distortion (THD) values for both KHN-equivalent biquads are below 1 %. The proposed two KHN-equivalent biquads have the advantages of high density, system integration, efficiency, low cost, low power consumption, and effective utilization of chip layout area. Simulations and on-chip measurements are carried out for both KHN-equivalent biquads to validate the theoretical design and demonstrate their on-chip feasibility.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 73056-73075
Open AccessChip Implementation of Two New VCII-Based Voltage/Transimpedance-Mode KHN-Equivalent Biquads
This paper presents two new VCII-based Kerwin-Huelsman-Newcomb (KHN) equivalent biquad circuits, each comprising three second-generation voltage conveyors (VCIIs), two grounded capacitors, and five resistors. Either voltage mode (VM) or trans-impedance mode (TIM) can operate in each proposed circuit configuration. Transfer function analysis using a VM inverting bandpass (IBP) filter yields two additional non-inverting/inverting KHN biquad transfer functions for the two proposed VM/TIM KHN-equivalent biquads. The first proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, a non-inverting low-pass (NLP) filter, and an inverting high-pass (IHP) filter. In contrast, the second proposed VM/TIM KHN-equivalent biquad can simultaneously implement an IBP filter, an inverting low-pass (ILP) filter, and a non-inverting high-pass (NHP) filter. Each proposed VM/TIM KHN-equivalent biquad features three low-impedance voltage outputs in the designed circuit, eliminating the need for additional voltage buffers (VBs) in the circuit measurements. The two proposed KHN-equivalent biquads are integrated into a single chip, occupying a total area of 1.44 mm2. This technology uses the TSMC 0.18 μm 1P6M CMOS process, with the chip operating at a supply voltage of ±0.9 V. The measured power dissipation of the first KHN-equivalent biquad is 2.7 mW, while the measured power dissipation of the second one is 3.24 mW. The measured spurious-free dynamic range (SFDR) of the first KHN-equivalent biquad is 41.18 dBc, while the measured SFDR of the second one is 40.94 dBc. With an input voltage of 1.2 Vpp, the measured total harmonic distortion (THD) values for both KHN-equivalent biquads are below 1 %. The proposed two KHN-equivalent biquads have the advantages of high density, system integration, efficiency, low cost, low power consumption, and effective utilization of chip layout area. Simulations and on-chip measurements are carried out for both KHN-equivalent biquads to validate the theoretical design and demonstrate their on-chip feasibility.
- Open Access
- 24 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 78040-78057
All-Pass Filter IC Design and Its Cascaded Second-Order and Third-Order All-Pass Filters and Quadrature Sinusoidal Oscillator Applications
This study presents the design and application of a cascaded voltage-mode (VM) first-order all-pass filter (APF) integrated circuit (IC) based on a positive differential current conveyor (DDCC+). The proposed single- and differential-input VM-APF uses two DDCC+ active components and two passive components consisting of a grounded capacitor and a resistor. Both non-inverting APF (NAPF) and inverting APF (IAPF) transfer functions of VM-APF can be implemented without any critical passive component matching condition. The proposed first-order VM-APF can realize both NAPF and IAPF transfer functions with high-input and low-output (HILO) impedance, which makes it suitable for cascading without any voltage buffer. Owing to the VM-APF with HILO impedance configuration, the proposed circuit can quickly cascade nth-order VM-APF without adding additional circuit architectures. The circuit is implemented on-chip based on TSMC 1P6M 180 nm process technology with a supply voltage of ±0.9 V. The first-order VM-APF power consumption is 1.8 mW. Integrating a first-order VM-APF into a single chip can improve system integration efficiency, reduce voltage and power consumption, and shrink circuit size. On-chip measurements verify the cascading feasibility of the proposed first-order VM-APF and demonstrate that the implemented chip can be easily cascaded for second- and third-order VM-APFs and VM APF-based quadrature sinusoidal oscillator applications.
- 24 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 78040-78057
Open AccessAll-Pass Filter IC Design and Its Cascaded Second-Order and Third-Order All-Pass Filters and Quadrature Sinusoidal Oscillator Applications
This study presents the design and application of a cascaded voltage-mode (VM) first-order all-pass filter (APF) integrated circuit (IC) based on a positive differential current conveyor (DDCC+). The proposed single- and differential-input VM-APF uses two DDCC+ active components and two passive components consisting of a grounded capacitor and a resistor. Both non-inverting APF (NAPF) and inverting APF (IAPF) transfer functions of VM-APF can be implemented without any critical passive component matching condition. The proposed first-order VM-APF can realize both NAPF and IAPF transfer functions with high-input and low-output (HILO) impedance, which makes it suitable for cascading without any voltage buffer. Owing to the VM-APF with HILO impedance configuration, the proposed circuit can quickly cascade nth-order VM-APF without adding additional circuit architectures. The circuit is implemented on-chip based on TSMC 1P6M 180 nm process technology with a supply voltage of ±0.9 V. The first-order VM-APF power consumption is 1.8 mW. Integrating a first-order VM-APF into a single chip can improve system integration efficiency, reduce voltage and power consumption, and shrink circuit size. On-chip measurements verify the cascading feasibility of the proposed first-order VM-APF and demonstrate that the implemented chip can be easily cascaded for second- and third-order VM-APFs and VM APF-based quadrature sinusoidal oscillator applications.
- Open Access
Design and Verification of a New Universal Active Filter Based on the Current Feedback Operational Amplifier and Commercial AD844 Integrated Circuit
This paper presents a triple-input and four-output type voltage-mode universal active filter based on three current-feedback operational amplifiers (CFOAs). The filter employs three CFOAs, two grounded capacitors, and six resistors. The filter structure has three high-input and three low-output impedances that simultaneously provide band-reject, high-pass, low-pass, and band-pass filtering functions with single-input and four-output type and also implements an all-pass filtering function by connecting three input signals to one input without the use of voltage inverters or switches. The same circuit configuration enables two unique filtering functions: low-pass notch and high-pass notch. Three CFOAs with three high-input and low-output impedance terminals enable cascading without voltage buffers. The circuit is implemented using three commercial off-the-shelf AD844 integrated circuits, two grounded capacitors, and six resistors and further implemented as a CFOA-based chip using three CFOAs, two grounded capacitors, and six resistors. The CFOA-based chip has lower power consumption and higher integration than the AD844-based filter. The circuit was simulated using OrCAD PSpice to verify the AD844-based filter and Synopsys HSpice for post-layout simulation of the CFOA-based chip. The theoretical analysis is validated and confirmed by measurements on an AD844-based filter and a CFOA-based chip.
Open AccessDesign and Verification of a New Universal Active Filter Based on the Current Feedback Operational Amplifier and Commercial AD844 Integrated Circuit
This paper presents a triple-input and four-output type voltage-mode universal active filter based on three current-feedback operational amplifiers (CFOAs). The filter employs three CFOAs, two grounded capacitors, and six resistors. The filter structure has three high-input and three low-output impedances that simultaneously provide band-reject, high-pass, low-pass, and band-pass filtering functions with single-input and four-output type and also implements an all-pass filtering function by connecting three input signals to one input without the use of voltage inverters or switches. The same circuit configuration enables two unique filtering functions: low-pass notch and high-pass notch. Three CFOAs with three high-input and low-output impedance terminals enable cascading without voltage buffers. The circuit is implemented using three commercial off-the-shelf AD844 integrated circuits, two grounded capacitors, and six resistors and further implemented as a CFOA-based chip using three CFOAs, two grounded capacitors, and six resistors. The CFOA-based chip has lower power consumption and higher integration than the AD844-based filter. The circuit was simulated using OrCAD PSpice to verify the AD844-based filter and Synopsys HSpice for post-layout simulation of the CFOA-based chip. The theoretical analysis is validated and confirmed by measurements on an AD844-based filter and a CFOA-based chip.
- Open Access
- 24 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 97400-97407
Ultra-Low Percentage Flicker High-Efficiency Direct AC LED Driver Using Constant Power Technology
According to California’s 2016 Building Energy Efficiency Standards, the percentage flicker of light-emitting diode (LED) lighting fixtures should be below 30 %. However, the percentage flicker of commercially available linear power supplies is generally between 25 % and 99.9 %; thus, some LED lighting fixtures that use linear power supplies have been unable to enter the European or American markets. The traditional method of effectively reducing flicker involves increasing the capacitance of the electrolytic capacitor of the power supply, which causes an increase in the height of the lamp board components as well as shadowing and dark band phenomena. This paper presents a power supply circuit that uses only electrolytic capacitors with low capacitance and exhibits constant power, constant light output, and a lamp board thickness of only 8 mm; it can achieve a percentage flicker of less than 10 %, which exceeds international standards. Power efficiency is a crucial performance indicator of linear power supplies. Because linear power supplies are mostly integrated circuits (ICs) with extremely small package volumes, higher power efficiency results in lower heat loss. The international standard for the power efficiency of linear power supplies is approximately 75 %. A multistage switching mechanism is used in the proposed power supply to achieve an overall efficiency of > 88 %. Under an input power of 12 W, a 10 % increase in efficiency reduces the heat by 1.2 W, which can considerably reduce the difficulty and cost of heat dissipation in IC packages. By combining the aforementioned technologies, the proposed power supply can achieve high efficiency and low percentage flicker, thereby improving the shortcomings of traditional linear power supplies. Currently, the driver-on-board (DOB) module of the proposed power supply is in the trial production phase, and its market entry will be accelerated to expand the market share of linear power supplies.
- 24 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 97400-97407
Open AccessUltra-Low Percentage Flicker High-Efficiency Direct AC LED Driver Using Constant Power Technology
According to California’s 2016 Building Energy Efficiency Standards, the percentage flicker of light-emitting diode (LED) lighting fixtures should be below 30 %. However, the percentage flicker of commercially available linear power supplies is generally between 25 % and 99.9 %; thus, some LED lighting fixtures that use linear power supplies have been unable to enter the European or American markets. The traditional method of effectively reducing flicker involves increasing the capacitance of the electrolytic capacitor of the power supply, which causes an increase in the height of the lamp board components as well as shadowing and dark band phenomena. This paper presents a power supply circuit that uses only electrolytic capacitors with low capacitance and exhibits constant power, constant light output, and a lamp board thickness of only 8 mm; it can achieve a percentage flicker of less than 10 %, which exceeds international standards. Power efficiency is a crucial performance indicator of linear power supplies. Because linear power supplies are mostly integrated circuits (ICs) with extremely small package volumes, higher power efficiency results in lower heat loss. The international standard for the power efficiency of linear power supplies is approximately 75 %. A multistage switching mechanism is used in the proposed power supply to achieve an overall efficiency of > 88 %. Under an input power of 12 W, a 10 % increase in efficiency reduces the heat by 1.2 W, which can considerably reduce the difficulty and cost of heat dissipation in IC packages. By combining the aforementioned technologies, the proposed power supply can achieve high efficiency and low percentage flicker, thereby improving the shortcomings of traditional linear power supplies. Currently, the driver-on-board (DOB) module of the proposed power supply is in the trial production phase, and its market entry will be accelerated to expand the market share of linear power supplies.
- Open Access
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1991
A New Control Scheme for the Buck Converter
In this paper, a new control scheme for buck converters was proposed. The buck converter utilizes the dual control loop to improve transient response and has the constant switching frequency. The control scheme is mainly as follows: (a) The switch-ON time is regulated by the constant frequency mechanism. (b) The switch-OFF time is regulated by the output voltage. The spec/features of the proposed converter are listed as: (1) The buck converter has an output of 1.0–2.5 V for the input of 3.0–3.6 V. The load current ranges from 100 mA to 500 mA. (2) The actual current sensor is not required. (3) The simulation results show that the recovery time is less than 1.6 μs during load changes. (4) The variation in switching frequency is smaller than 1.05% over the output range of 1.0–2.5 V. (5) This circuit can be fabricated in future by UMC 0.18 μm 1P6M CMOS processes. This paper depicts the control scheme, theoretical analysis, and implementation.
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1991
Open AccessA New Control Scheme for the Buck Converter
In this paper, a new control scheme for buck converters was proposed. The buck converter utilizes the dual control loop to improve transient response and has the constant switching frequency. The control scheme is mainly as follows: (a) The switch-ON time is regulated by the constant frequency mechanism. (b) The switch-OFF time is regulated by the output voltage. The spec/features of the proposed converter are listed as: (1) The buck converter has an output of 1.0–2.5 V for the input of 3.0–3.6 V. The load current ranges from 100 mA to 500 mA. (2) The actual current sensor is not required. (3) The simulation results show that the recovery time is less than 1.6 μs during load changes. (4) The variation in switching frequency is smaller than 1.05% over the output range of 1.0–2.5 V. (5) This circuit can be fabricated in future by UMC 0.18 μm 1P6M CMOS processes. This paper depicts the control scheme, theoretical analysis, and implementation.
- Open Access
Four Unity/Variable Gain First-Order Cascaded Voltage-Mode All-Pass Filters and Their Fully Uncoupled Quadrature Sinusoidal Oscillator Applications
This paper presents four new designs for a first-order voltage-mode (VM) all-pass filter (APF) circuit based on two single-output positive differential voltage current conveyors (DVCCs). The first two proposed VMAPFs with unity-gain, high-input (HI) impedance and low-output (LO) impedance use two DVCCs, a grounded capacitor, and a grounded resistor. The last two proposed first-order VMAPFs with HI impedance and variable-gain control are two resistors added to each of the first two VMAPFs. The last two proposed first-order VMAPFs with variable-gain control use two DVCCs, one grounded capacitor, and three grounded resistors and provide HI impedances, so that VMAPFs can be directly cascaded to obtain high-order filters without additional voltage buffers. The four implementation circuits based only on grounded passive components are particularly applicable for integrated circuits (ICs). To confirm the cascading characteristics, an application example of a fully-uncoupled quadrature sinusoidal oscillator (FQSO) is also proposed. PSpice simulation results have confirmed the feasibility of the proposed structures. VMAPF and FQSO circuits are also constructed from commercial AD8130 and AD844 ICs, and their experimentally measured time and frequency responses are compared to theoretical values. The supply voltages for both the AD8130 and AD844 ICs were ±5 V. The measured power dissipation of the proposed first-order VMAPF and second-order FQSO circuits is 0.6 W. The measured input 1-dB compression point for the four VMAPFs is about 19 dB. The measured total harmonic distortion of the four VMAPFs is less than 0.67% when the input voltage reaches 2.5 Vpp. The calculated figures of merit for the four VMAPFs are 628.2 × 103, 603.06 × 103, 516.53 × 103, and 496.42 × 103, respectively.
Open AccessFour Unity/Variable Gain First-Order Cascaded Voltage-Mode All-Pass Filters and Their Fully Uncoupled Quadrature Sinusoidal Oscillator Applications
This paper presents four new designs for a first-order voltage-mode (VM) all-pass filter (APF) circuit based on two single-output positive differential voltage current conveyors (DVCCs). The first two proposed VMAPFs with unity-gain, high-input (HI) impedance and low-output (LO) impedance use two DVCCs, a grounded capacitor, and a grounded resistor. The last two proposed first-order VMAPFs with HI impedance and variable-gain control are two resistors added to each of the first two VMAPFs. The last two proposed first-order VMAPFs with variable-gain control use two DVCCs, one grounded capacitor, and three grounded resistors and provide HI impedances, so that VMAPFs can be directly cascaded to obtain high-order filters without additional voltage buffers. The four implementation circuits based only on grounded passive components are particularly applicable for integrated circuits (ICs). To confirm the cascading characteristics, an application example of a fully-uncoupled quadrature sinusoidal oscillator (FQSO) is also proposed. PSpice simulation results have confirmed the feasibility of the proposed structures. VMAPF and FQSO circuits are also constructed from commercial AD8130 and AD844 ICs, and their experimentally measured time and frequency responses are compared to theoretical values. The supply voltages for both the AD8130 and AD844 ICs were ±5 V. The measured power dissipation of the proposed first-order VMAPF and second-order FQSO circuits is 0.6 W. The measured input 1-dB compression point for the four VMAPFs is about 19 dB. The measured total harmonic distortion of the four VMAPFs is less than 0.67% when the input voltage reaches 2.5 Vpp. The calculated figures of merit for the four VMAPFs are 628.2 × 103, 603.06 × 103, 516.53 × 103, and 496.42 × 103, respectively.
- Open Access
- 5 May 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1484
Design of the Buck Converter without Inductor Current Sensor
This paper proposes a novel control scheme for the buck converter without an inductor current sensor. The architecture of the proposed buck converter is simple and suitable for integration and mass production. It employs an output-voltage-measurement method to determine the switch ON time; therefore, the current sensor is not required. The design specification targets the application with a standard battery power source to generate the low voltages for low-power MCU or ASIC. The load current range aims for several hundred milliamps. The proposed control scheme is analyzed and simulated by SIMPLIS. The control scheme, theoretical analysis, circuit realization, contributions, advantages, and simulation results are presented in this paper. Furthermore, the circuit can be fabricated by a 0.35 μm CMOS process.
- 5 May 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1484
Open AccessDesign of the Buck Converter without Inductor Current Sensor
This paper proposes a novel control scheme for the buck converter without an inductor current sensor. The architecture of the proposed buck converter is simple and suitable for integration and mass production. It employs an output-voltage-measurement method to determine the switch ON time; therefore, the current sensor is not required. The design specification targets the application with a standard battery power source to generate the low voltages for low-power MCU or ASIC. The load current range aims for several hundred milliamps. The proposed control scheme is analyzed and simulated by SIMPLIS. The control scheme, theoretical analysis, circuit realization, contributions, advantages, and simulation results are presented in this paper. Furthermore, the circuit can be fabricated by a 0.35 μm CMOS process.
- Open Access
- 15 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (8) , 1256
A Novel Buck Converter with Dual Loops Control Mechanism
This paper presents a novel buck converter with dual-loop control technology, which does not need to detect the inductor current directly. The structure of the control loops is easy to implement, one loop controls the output voltage, and the other controls the switching frequency. With the dual loops control mechanism, the output voltage and switching frequency can be accurately controlled only by measuring the output and input voltage, without sensing the inductor current. The buck converter can generate an output voltage of 1.0–2.5 V when the input voltage and load current are 3.0–3.6 V and 100–500 mA, respectively. The design was verified by SIMPLIS. The simulation results show that the switching frequency variation is less than 1% at the output voltage of 1.0–2.5 V. The recovery time is less than 1.5 μs during the load change. The circuit can be fabricated by using the TSMC 0.35μm 2P4M CMOS processes. The control scheme, theoretical analysis and circuit implementation are presented in this paper.
- 15 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (8) , 1256
Open AccessA Novel Buck Converter with Dual Loops Control Mechanism
This paper presents a novel buck converter with dual-loop control technology, which does not need to detect the inductor current directly. The structure of the control loops is easy to implement, one loop controls the output voltage, and the other controls the switching frequency. With the dual loops control mechanism, the output voltage and switching frequency can be accurately controlled only by measuring the output and input voltage, without sensing the inductor current. The buck converter can generate an output voltage of 1.0–2.5 V when the input voltage and load current are 3.0–3.6 V and 100–500 mA, respectively. The design was verified by SIMPLIS. The simulation results show that the switching frequency variation is less than 1% at the output voltage of 1.0–2.5 V. The recovery time is less than 1.5 μs during the load change. The circuit can be fabricated by using the TSMC 0.35μm 2P4M CMOS processes. The control scheme, theoretical analysis and circuit implementation are presented in this paper.
- Open Access
- 3 September 2021
- Published by MDPI AG in Electronics
- Vol. 10 (17) , 2143
Adaptive On-Time Control Buck Converter with a Novel Virtual Inductor Current Circuit
This study presents a new virtual inductor current circuit to reduce circuit complexity, which is not necessary to sense inductance current directly. The buck converter was designed to produce an output voltage of 1.0–2.5 V for a 3.0–3.6 V input voltage. The load current range was from 100 mA to 500 mA. It was simulated and verified by SIMPLIS and MathCAD. The simulation results of this buck converter show that the voltage error is within 1%, and the recovery time is smaller than 2 ms for step-up and step-down load transients. Additionally, it achieves less than 26 mV overshoot at full-load step transient response. The circuit topology would be able to fabricate using TSMC 0.35 mm 2P4M CMOS technology. The control mechanism, implementation, and design procedure are presented in this paper.
- 3 September 2021
- Published by MDPI AG in Electronics
- Vol. 10 (17) , 2143
Open AccessAdaptive On-Time Control Buck Converter with a Novel Virtual Inductor Current Circuit
This study presents a new virtual inductor current circuit to reduce circuit complexity, which is not necessary to sense inductance current directly. The buck converter was designed to produce an output voltage of 1.0–2.5 V for a 3.0–3.6 V input voltage. The load current range was from 100 mA to 500 mA. It was simulated and verified by SIMPLIS and MathCAD. The simulation results of this buck converter show that the voltage error is within 1%, and the recovery time is smaller than 2 ms for step-up and step-down load transients. Additionally, it achieves less than 26 mV overshoot at full-load step transient response. The circuit topology would be able to fabricate using TSMC 0.35 mm 2P4M CMOS technology. The control mechanism, implementation, and design procedure are presented in this paper.