Samir Ghosh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Samir Ghosh has a total of 96 co-authors. Here are the top co-authors by number of shared publications:
Alireza Samani
Photonic Systems Group, McGill University, Montréal, QC, Canada
9 shared publicationsDavid V. Plant
Photonic Systems Group, McGill University, Montréal, QC, Canada
9 shared publicationsYoshiaki Nakano
Department of Electric Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo, 113-9656, Japan
8 shared publicationsDavid Patel
Photonic Systems Group, McGill University, Montréal, QC, Canada
7 shared publications- Takuo Tanemura
Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656, Japan
6 shared publications Qiuhang Zhong
Department of Electrical and Computer Engineering, McGill University, Montreal, QC, Canada
5 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (21) , 39718
Integrated gain-controlled semiconductor optical amplifier for input-power range extension in 100 Gb/s upstream PON receiver applications
High-speed operation for upstream passive optical network (PON) applications enabled by bias-controlled operation of silicon photonics integrated semiconductor optical amplifiers (SOA) is demonstrated in a continuous-mode back-to-back configuration. The InP-based C-band SOAs are heterogeneously integrated onto a 400 nm thick silicon waveguide using micro-transfer printing technology. Optimized apodized grating couplers are designed and incorporated to minimize fiber-to-chip coupling loss (2.5 dB). The integrated SOAs exhibit small-signal on-chip gains of 15–17 dB at a bias current of 120 mA. When the integrated SOA is employed as a receiver-side preamplifier in a 100 Gb/s four-level pulse-amplitude modulation (PAM-4) upstream PON application, bias optimization across received power levels extends the SOA operating input power range to 22 dB while mitigating pattern-dependent distortion arising from SOA gain saturation. A minimum SOA input power of −23 dBm is achieved at the hard-decision forward error-correction threshold, referenced to the on-chip SOA input and excluding input grating-coupler loss. These results demonstrate the potential of heterogeneously integrated, bias-controlled SOAs as compact preamplifiers for extending the operating input power range of next-generation high-speed upstream PON receivers.
- 12 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (21) , 39718
Open AccessIntegrated gain-controlled semiconductor optical amplifier for input-power range extension in 100 Gb/s upstream PON receiver applications
High-speed operation for upstream passive optical network (PON) applications enabled by bias-controlled operation of silicon photonics integrated semiconductor optical amplifiers (SOA) is demonstrated in a continuous-mode back-to-back configuration. The InP-based C-band SOAs are heterogeneously integrated onto a 400 nm thick silicon waveguide using micro-transfer printing technology. Optimized apodized grating couplers are designed and incorporated to minimize fiber-to-chip coupling loss (2.5 dB). The integrated SOAs exhibit small-signal on-chip gains of 15–17 dB at a bias current of 120 mA. When the integrated SOA is employed as a receiver-side preamplifier in a 100 Gb/s four-level pulse-amplitude modulation (PAM-4) upstream PON application, bias optimization across received power levels extends the SOA operating input power range to 22 dB while mitigating pattern-dependent distortion arising from SOA gain saturation. A minimum SOA input power of −23 dBm is achieved at the hard-decision forward error-correction threshold, referenced to the on-chip SOA input and excluding input grating-coupler loss. These results demonstrate the potential of heterogeneously integrated, bias-controlled SOAs as compact preamplifiers for extending the operating input power range of next-generation high-speed upstream PON receivers.
- Open Access
- 1 September 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (18) , 33904
Scalable transfer printing approach for heterogeneous integration of magneto-optic material onto silicon photonics platform
Nonreciprocal devices such as optical isolators and circulators are sought-after components for photonic integrated circuits (PICs) in order to ensure the stability of integrated lasers. Magneto-optic (MO) properties can be utilized to provide this functionality. MO materials are incompatible with front-end integration on PICs fabricated in complementary metal oxide semiconductor foundries. Post-process heterogeneous integration is therefore the preferred route. In this work, we experimentally demonstrate a micro transfer printing-based approach to integrate MO thin-film materials onto silicon waveguides. MO films were deposited on a silicon-on-insulator chip with a seed layer from which transfer-printable coupons were dry-released and printed onto racetrack resonator-based devices using a thin adhesive layer. We measured an isolation in the range of 14-18 dB for transverse-magnetic polarized light at telecommunication wavelengths for a coupon length of 1.6 mm. This coupon-based integration approach offers unprecedented freedom for future heterogeneously integrated PICs containing thousands of components.
- 1 September 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (18) , 33904
Open AccessScalable transfer printing approach for heterogeneous integration of magneto-optic material onto silicon photonics platform
Nonreciprocal devices such as optical isolators and circulators are sought-after components for photonic integrated circuits (PICs) in order to ensure the stability of integrated lasers. Magneto-optic (MO) properties can be utilized to provide this functionality. MO materials are incompatible with front-end integration on PICs fabricated in complementary metal oxide semiconductor foundries. Post-process heterogeneous integration is therefore the preferred route. In this work, we experimentally demonstrate a micro transfer printing-based approach to integrate MO thin-film materials onto silicon waveguides. MO films were deposited on a silicon-on-insulator chip with a seed layer from which transfer-printable coupons were dry-released and printed onto racetrack resonator-based devices using a thin adhesive layer. We measured an isolation in the range of 14-18 dB for transverse-magnetic polarized light at telecommunication wavelengths for a coupon length of 1.6 mm. This coupon-based integration approach offers unprecedented freedom for future heterogeneously integrated PICs containing thousands of components.
- Open Access
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Scalable transfer printing approach to heterogeneous integration of InP lasers on silicon-on-insulator waveguide platform
InP-based edge-emitting O-band lasers are integrated onto silicon photonics circuit employing micro-transfer printing technology. Blocks of unpatterned InP gain material of typical size 1000 × 60 μ m2 are first transferred onto 400 nm thick silicon rib waveguides with the fabrication steps performed on the target wafer to realize the final lasers. As a result, the InP ridge waveguides are aligned with lithographic accuracy to the underlying Si waveguides resulting in an approach free from any misalignment stemming from the transfer printing process. The fabricated Distributed Bragg Reflector laser shows lasing around 100 mA current injection with minimum 1 mW of output power coupled to a single mode fiber. This integration method paves a reliable route toward scaling-up the integration of active devices such as lasers, modulators, and detectors on 300-mm diameter silicon wafers, which requires high-uniformity across the wafer.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Open AccessScalable transfer printing approach to heterogeneous integration of InP lasers on silicon-on-insulator waveguide platform
InP-based edge-emitting O-band lasers are integrated onto silicon photonics circuit employing micro-transfer printing technology. Blocks of unpatterned InP gain material of typical size 1000 × 60 μ m2 are first transferred onto 400 nm thick silicon rib waveguides with the fabrication steps performed on the target wafer to realize the final lasers. As a result, the InP ridge waveguides are aligned with lithographic accuracy to the underlying Si waveguides resulting in an approach free from any misalignment stemming from the transfer printing process. The fabricated Distributed Bragg Reflector laser shows lasing around 100 mA current injection with minimum 1 mW of output power coupled to a single mode fiber. This integration method paves a reliable route toward scaling-up the integration of active devices such as lasers, modulators, and detectors on 300-mm diameter silicon wafers, which requires high-uniformity across the wafer.
- Open Access
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
Micro-transfer printed high-speed InP-based electro-absorption modulator on silicon-on-insulator
A high-speed InP-based electro-absorption modulator (EAM) on 220 nm silicon-on-insulator (SOI) is designed, fabricated, and measured. The III–V device is heterogeneously integrated to the SOI using transfer printing, with direct bonding. The printing accuracy of the device was within ±0.5 μm. This design evanescently couples light between the III–V waveguide and the SOI via a taper region in the InP ridge for high transmission. This method is a flexible and robust method of transferring an InP EAM to SOI, where multiple device variations have been transferred. At 1550 nm, the printed EAM has a measured electrical bandwidth of up to 40 GHz, an extinction ratio (ER) of 30 dB from 0 to −6 V, and an insertion loss of 6.5 dB, which reduces with longer wavelengths. An ER of 25 dB is obtained over a spectral bandwidth of 30 nm with biasing to −8 V. Open-eye diagrams were measured up to 50 Gbps in a back-to-back measurement. This device is suitable for applications in high-speed communications and sensing, leveraging the added advantage of III–V absorption modulation on a silicon photonics platform.
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
Open AccessMicro-transfer printed high-speed InP-based electro-absorption modulator on silicon-on-insulator
A high-speed InP-based electro-absorption modulator (EAM) on 220 nm silicon-on-insulator (SOI) is designed, fabricated, and measured. The III–V device is heterogeneously integrated to the SOI using transfer printing, with direct bonding. The printing accuracy of the device was within ±0.5 μm. This design evanescently couples light between the III–V waveguide and the SOI via a taper region in the InP ridge for high transmission. This method is a flexible and robust method of transferring an InP EAM to SOI, where multiple device variations have been transferred. At 1550 nm, the printed EAM has a measured electrical bandwidth of up to 40 GHz, an extinction ratio (ER) of 30 dB from 0 to −6 V, and an insertion loss of 6.5 dB, which reduces with longer wavelengths. An ER of 25 dB is obtained over a spectral bandwidth of 30 nm with biasing to −8 V. Open-eye diagrams were measured up to 50 Gbps in a back-to-back measurement. This device is suitable for applications in high-speed communications and sensing, leveraging the added advantage of III–V absorption modulation on a silicon photonics platform.
- 1 January 2023
- Published by Optica Publishing Group
- p. Th5A.3
Next-generation Large-scale PIC Enabled by Micro-transfer Printing Technology
Here, we present micro-transfer printing as a versatile heterogeneous integration technique that allows dense integration of multiple material systems on the same waveguide platform through a parallel and scalable process.
- 1 January 2023
- Published by Optica Publishing Group
- p. Th5A.3
Next-generation Large-scale PIC Enabled by Micro-transfer Printing Technology
Here, we present micro-transfer printing as a versatile heterogeneous integration technique that allows dense integration of multiple material systems on the same waveguide platform through a parallel and scalable process.
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (15) , 1233-1236
Offset-Quantum-Well-Based Integrated Stokes Vector Modulator on InP
We demonstrate an offset-quantum-well based Stokes vector modulator (SVM) on InP with compressively-strained InGaAsP/InGaAsP multiple-quantum-wells (MQWs). Tuning the applied voltages to the phase modulators, arbitrary state-of-polarization (SOP) is generated at the output. A single metal-organic chemical vapor deposition (MOCVD) regrowth step is employed for integrating a pair of passive polarization converters (PCs) and active MQW-based polarization-dependent phase modulator (PD-PM) sections. All components are concatenated in series on an offset-quantum well (OQW) platform. A 3.5 mm long SVM has a PD-PM with half-wave voltage Vπ of 14 V and a VπL of 2.1 V.cm.
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (15) , 1233-1236
Offset-Quantum-Well-Based Integrated Stokes Vector Modulator on InP
We demonstrate an offset-quantum-well based Stokes vector modulator (SVM) on InP with compressively-strained InGaAsP/InGaAsP multiple-quantum-wells (MQWs). Tuning the applied voltages to the phase modulators, arbitrary state-of-polarization (SOP) is generated at the output. A single metal-organic chemical vapor deposition (MOCVD) regrowth step is employed for integrating a pair of passive polarization converters (PCs) and active MQW-based polarization-dependent phase modulator (PD-PM) sections. All components are concatenated in series on an offset-quantum well (OQW) platform. A 3.5 mm long SVM has a PD-PM with half-wave voltage Vπ of 14 V and a VπL of 2.1 V.cm.
- 1 January 2019
- Published by Optica Publishing Group
- p. Th1E.3
Integrated Reconfigurable 4×4 Optical Unitary Converter Using Multiport Directional Couplers
We demonstrate novel silicon photonic 44 reconfigurable optical unitary converter, comprising multiport directional couplers and phase shifter arrays. By optimizing the phase shift with simulated annealing algorithm, reconfigurable mode sorting and switching are experimentally realized.
- 1 January 2019
- Published by Optica Publishing Group
- p. Th1E.3
Integrated Reconfigurable 4×4 Optical Unitary Converter Using Multiport Directional Couplers
We demonstrate novel silicon photonic 44 reconfigurable optical unitary converter, comprising multiport directional couplers and phase shifter arrays. By optimizing the phase shift with simulated annealing algorithm, reconfigurable mode sorting and switching are experimentally realized.
- 1 January 2019
- Published by Optica Publishing Group
- p. W3B.6
4-port Integrated Stokes Vector Receiver Circuit for Multi-level 3D Signal Detection and OSNR Monitoring
A novel Stokes vector (SV) receiver circuit with 4-port configuration integrated on a compact InP chip is fabricated to demonstrate SV retrieval with various intensity and degree-of-polarization as well as application to in-band OSNR monitoring.
- 1 January 2019
- Published by Optica Publishing Group
- p. W3B.6
4-port Integrated Stokes Vector Receiver Circuit for Multi-level 3D Signal Detection and OSNR Monitoring
A novel Stokes vector (SV) receiver circuit with 4-port configuration integrated on a compact InP chip is fabricated to demonstrate SV retrieval with various intensity and degree-of-polarization as well as application to in-band OSNR monitoring.
- 11 April 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (8) , 1798-1801
Reconfigurable all-optical on-chip MIMO three-mode demultiplexing based on multi-plane light conversion
We present, to the best of our knowledge, the first experimental demonstration of reconfigurable all-optical on-chip multi-input-multi-output three-mode demultiplexing based on multi-plane light conversion. The demultiplexer consists of cascaded phase shifter arrays and multimode interference couplers integrated on a compact silicon chip. By optimizing the phase shifters, reconfigurable three-mode demultiplexing is experimentally realized with wavelength-dependent loss of less than 3 dB and modal crosstalk of less than over a 23 nm optical bandwidth. Error-free mode demultiplexing of 40 Gbps non-return-to-zero signal is also demonstrated.- 11 April 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (8) , 1798-1801
Reconfigurable all-optical on-chip MIMO three-mode demultiplexing based on multi-plane light conversion
We present, to the best of our knowledge, the first experimental demonstration of reconfigurable all-optical on-chip multi-input-multi-output three-mode demultiplexing based on multi-plane light conversion. The demultiplexer consists of cascaded phase shifter arrays and multimode interference couplers integrated on a compact silicon chip. By optimizing the phase shifters, reconfigurable three-mode demultiplexing is experimentally realized with wavelength-dependent loss of less than 3 dB and modal crosstalk of less than over a 23 nm optical bandwidth. Error-free mode demultiplexing of 40 Gbps non-return-to-zero signal is also demonstrated.- 10 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 187-194
Decoding of Multilevel Stokes-Vector Modulated Signal by Polarization-Analyzing Circuit on InP
Of-late research on Stokes vector receiver for the short-reach optical communication has gained significant attention due to its capability to decode information in multi-dimension using cost-effective direct-detection technique. Here, we report a compact and robust photonic integrated circuit (PIC) on InP for potentially low-cost direct-detection-based Stokes vector (SV) receiver. It consists of a $1\times4$ multimode interference power splitter with different combination of polarization converters on output arms, so that input SV is projected onto distinct vectors on the Stokes space. By using the fabricated device, we experimentally demonstrate decoding of 2-level and 4-level SV-modulated signals at 3 Gbaud. With the potential of monolithically integrating high-speed InP photodetector array on the same chip, it paves the way to realize compact and low-cost SV receivers for multi-level SV modulation formats in future short-reach optical communication links.- 10 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 187-194
Decoding of Multilevel Stokes-Vector Modulated Signal by Polarization-Analyzing Circuit on InP
Of-late research on Stokes vector receiver for the short-reach optical communication has gained significant attention due to its capability to decode information in multi-dimension using cost-effective direct-detection technique. Here, we report a compact and robust photonic integrated circuit (PIC) on InP for potentially low-cost direct-detection-based Stokes vector (SV) receiver. It consists of a $1\times4$ multimode interference power splitter with different combination of polarization converters on output arms, so that input SV is projected onto distinct vectors on the Stokes space. By using the fabricated device, we experimentally demonstrate decoding of 2-level and 4-level SV-modulated signals at 3 Gbaud. With the potential of monolithically integrating high-speed InP photodetector array on the same chip, it paves the way to realize compact and low-cost SV receivers for multi-level SV modulation formats in future short-reach optical communication links.